DIYbanter

DIYbanter (https://www.diybanter.com/)
-   Woodworking (https://www.diybanter.com/woodworking/)
-   -   How to install new drive belt...Ryobi BE-321 3x21 belt sander (https://www.diybanter.com/woodworking/107829-how-install-new-drive-belt-ryobi-321-3x21-belt-sander.html)

jbclem May 30th 05 11:00 PM

How to install new drive belt...Ryobi BE-321 3x21 belt sander
 
I have a new drive belt for my Ryobi 3x21 belt sander and there is no obvious way to
loosen or move either of the two pulleys it fits over. I'm not sure if it's a matter of
push and shove or if I need to disassemble/remove a pulley. Both pulleys seem to be on
straight shafts with no provision for adjusting one of them.

Any suggestions?

John



Lee DeRaud May 31st 05 12:02 AM

On Mon, 30 May 2005 15:00:29 -0700, "jbclem"
wrote:

I have a new drive belt for my Ryobi 3x21 belt sander and there is no obvious way to
loosen or move either of the two pulleys it fits over. I'm not sure if it's a matter of
push and shove or if I need to disassemble/remove a pulley. Both pulleys seem to be on
straight shafts with no provision for adjusting one of them.

Any suggestions?


Uh, "tension release lever"? (On the 3x18 model, it's right side,
between the pulleys, pull out to release, push in to retension.)

Lee

Edwin Pawlowski May 31st 05 12:23 AM


"Lee DeRaud" wrote in message
On Mon, 30 May 2005 15:00:29 -0700, "jbclem"
wrote:

I have a new drive belt for my Ryobi 3x21 belt sander and there is no
obvious way to
loosen or move either of the two pulleys it fits over. I'm not sure if
it's a matter of
push and shove or if I need to disassemble/remove a pulley. Both pulleys
seem to be on
straight shafts with no provision for adjusting one of them.

Any suggestions?


Uh, "tension release lever"? (On the 3x18 model, it's right side,
between the pulleys, pull out to release, push in to retension.)

Lee


I'm confused. The OP asks about a drive belt but gives a description that
sounds much like a sanding belt. You give instruction for the sanding belt.
Just what is being replaced? When I hear the term "drive belt" I think of
a belt from the motor pulley to the wheel pulley.



CW May 31st 05 12:36 AM

Keyword: DRIVE belt.

"Lee DeRaud" wrote in message
...

Uh, "tension release lever"? (On the 3x18 model, it's right side,
between the pulleys, pull out to release, push in to retension.)

Lee




SouthForkSam May 31st 05 04:31 AM

When I changed my belt on the same model, I pulled the washer and nut
off of the main drive pulley, aligned the teeth with the cogs and
worked it on. Then I put the washer and bolt back on. Does that make
sense?


Lobby Dosser May 31st 05 04:44 AM

"jbclem" wrote:

I have a new drive belt for my Ryobi 3x21 belt sander and there is no
obvious way to loosen or move either of the two pulleys it fits over.
I'm not sure if it's a matter of push and shove or if I need to
disassemble/remove a pulley. Both pulleys seem to be on straight
shafts with no provision for adjusting one of them.

Any suggestions?

John



Well, the manual is no help and nether is the Ryobi site. Try looking at
the parts diagram he

http://m-and-d.com/ryobi_tools.html Box in center of the page will lead
you to the proper parts diagram. You might have a better chance of
figuring it out.

My manual has instructions for idiots in four languages, but no parts
diagram. Please post results!

LD.

jbclem May 31st 05 09:50 AM

You are right Sam. I took off the alignment washer and nut and also the main drive
pulley. Then I fit the belt over both pulleys (the main pulley being loose still), and
to be able to work the main pulley back on the shaft I had to push the shaft/roller down
out of position so that when I pushed the main drive pulley(and the belt) back over the
shaft the main pulley was partially descended into the hole the roller occupied. That
was the angle of least resistance and was the easiest way to get the pulley (pulled
tight by the belt) back onto the shaft. Once the main pulley was partway onto the shaft
I then knocked the other end of the shaft/roller and that pushed the shaft all the way
into and through the main pulley. Then the alignment washer and nut and bingo!

Didn't take but 5 minutes, next time will only take 2.

John







"SouthForkSam" wrote in message
oups.com...
When I changed my belt on the same model, I pulled the washer and nut
off of the main drive pulley, aligned the teeth with the cogs and
worked it on. Then I put the washer and bolt back on. Does that make
sense?




Lee DeRaud May 31st 05 10:24 PM

On Mon, 30 May 2005 23:23:42 GMT, "Edwin Pawlowski"
wrote:


"Lee DeRaud" wrote in message
On Mon, 30 May 2005 15:00:29 -0700, "jbclem"
wrote:

I have a new drive belt for my Ryobi 3x21 belt sander and there is no
obvious way to
loosen or move either of the two pulleys it fits over. I'm not sure if
it's a matter of
push and shove or if I need to disassemble/remove a pulley. Both pulleys
seem to be on
straight shafts with no provision for adjusting one of them.

Any suggestions?


Uh, "tension release lever"? (On the 3x18 model, it's right side,
between the pulleys, pull out to release, push in to retension.)

Lee


I'm confused. The OP asks about a drive belt but gives a description that
sounds much like a sanding belt. You give instruction for the sanding belt.


Yeah, he confused me too. Ignore all after.

Lee


All times are GMT +1. The time now is 08:18 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter