I have a project that I have just finished sanding. What is the best way to
remove the sawdust before finishing it? I seem to remeber reading something
recently to stay away from tack cloths as they leave a residue?

Thanks.

Stacey

I NEVER use tack cloths any longer. A good shop vac with a round brush
attachment (I wrap tape around the brush to stiffen them) is what I use.
Sometimes I also blow out the pores with a heavy blast of compressed
air (with the doors open with cross ventilation so the dust goes
bye-bye), followed by the aforementioned vacuum treatment. I use fast
drying finishes and have no trouble with dust. Cloths can leave bits of
lint. Tack cloths can mess up your finish.

Dave

Stacey wrote:

I have a project that I have just finished sanding. What is the best way to
remove the sawdust before finishing it? I seem to remeber reading something
recently to stay away from tack cloths as they leave a residue?

Thanks.

Stacey

Compressed air from a tank isn't such a good idea. Lubircating oil, and
moisture can be sprayed onto your project, and that will definately stain
wood, or screw up finishes. Go with dave's aforementioned vacuum treatment.

SCB.

Good point; you have to spray ONLY clean air!

Dave

SatansCabanaBoy wrote:

Compressed air from a tank isn't such a good idea. Lubircating oil, and
moisture can be sprayed onto your project, and that will definately stain
wood, or screw up finishes. Go with dave's aforementioned vacuum treatment.

SCB.

Is it true this is less of a problem (or no problem) with oiless
compressors? Is there a reliable, inexpensive way to filter otherwise?

"David" wrote in message
...
Good point; you have to spray ONLY clean air!

Dave

SatansCabanaBoy wrote:

Compressed air from a tank isn't such a good idea. Lubircating oil, and
moisture can be sprayed onto your project, and that will definately stain
wood, or screw up finishes. Go with dave's aforementioned vacuum
treatment.

SCB.

"Fourleaves" wrote in message
hlink.net...
Is it true this is less of a problem (or no problem) with oiless
compressors? Is there a reliable, inexpensive way to filter otherwise?


I do it with an oiless. Yes, there are filters available if you have oil in
the air. This is more important with older compressors as the rings wear.
It is also a method I use only if the weather is warm enough to do it
outside. In the shop you just blow a lot of air and stir up more dust.
--
Ed
http://pages.cthome.net/edhome/

On Mon, 30 May 2005 03:51:00 GMT, the inscrutable "Fourleaves"
spake:

Is it true this is less of a problem (or no problem) with oiless
compressors? Is there a reliable, inexpensive way to filter otherwise?

Harbor Freight has filter/regulator sets on sale for $20 quite often.
Grab one of those and your compressor will be set for life.

I blow off any sanding dust (or, more often, scraping curlies)
then wipe down the surface with denatured alcohol or lacquer thinner.
Within minutes, I'm putting finish on. Since I like wiping varnishes
and satin finishes, dust isn't as large a problem for me as it is with
those who like those glaring pinanner finishes.

P.S: Please learn to bottom-post.


--
If you turn the United States on its side,
everything loose will fall to California.
--Frank Lloyd Wright

I use a filter at the end of the line just ahead of the gun/nozzle
with an oiled compressor.

On Mon, 30 May 2005 03:51:00 GMT, "Fourleaves"
wrote:

Is it true this is less of a problem (or no problem) with oiless
compressors? Is there a reliable, inexpensive way to filter otherwise?

With oil, I don't bother. It just doesn't seem to make any difference.

With varnish, I use a cloth dampened with mineral spirits.

I have a project that I have just finished sanding. What is the best way to
remove the sawdust before finishing it? I seem to remeber reading something recently to stay away from tack cloths as they leave a
residue?

Thanks.

Stacey

Scraping. It is a whole art of it's own:

http://www.leevalley.com/wood/page.a...=1,310&p=48431
http://www.leevalley.com/wood/page.a...=1,310&p=45784
http://www.leevalley.com/wood/page.a...=1,310&p=46266
http://www.leevalley.com/wood/page.a...=1,310&p=32669
My choice:
http://www.leevalley.com/wood/page.a...=1,310&p=32635
A scraping blade must be burnished:
http://www.leevalley.com/wood/page.a...=1,310&p=41070
Handheld blades:
http://www.leevalley.com/wood/page.a...=1,310&p=41069

Scraping is an aquired art to a degree, especially in conditioning the blade.
But it leaves wood very very smooth.

--
Alex - newbie_neander in woodworking
cravdraa_at-yahoo_dot-com
not my site: http://www.e-sword.net/

Stacey says...

I have a project that I have just finished sanding. What is the best way to
remove the sawdust before finishing it? I seem to remeber reading something
recently to stay away from tack cloths as they leave a residue?

Thanks.

Stacey

I use a vacuum, a tack cloth and a wipe down with naphtha in that order.
The naphtha will take away any tack rag residue and it is good for
removing all the other gunk sticking to your wood like skin oil, and
oil, grease and wax from machines. There are also tack rags available
that don't use a sticky residue, but collect the dust in the fibers of
the cloth.

On Sun, 29 May 2005 21:05:40 -0500, Hax Planx
wrote:

I use a vacuum, a tack cloth and a wipe down with naphtha in that order.
The naphtha will take away any tack rag residue and it is good for
removing all the other gunk sticking to your wood like skin oil, and
oil, grease and wax from machines. There are also tack rags available
that don't use a sticky residue, but collect the dust in the fibers of
the cloth.

You'll find a ton of other similarly dangerous solvents to do the same
job. However, I'd recommend alcohol as being the lesser of all evils
[when used externally :-) ]. Volatile naphtha is positively
definitely out in my book.

Also recommended, likely understood, but worth a mention ...a lightly
damped cloth, used quickly enough to avoid evaporation, not a soaking
of the wood.

Guess who says...

You'll find a ton of other similarly dangerous solvents to do the same
job. However, I'd recommend alcohol as being the lesser of all evils
[when used externally :-) ]. Volatile naphtha is positively
definitely out in my book.

Unfortunately, nothing compares to naphtha for cleaning up grease and
oil and just because you can't see any doesn't mean it isn't there.
Alcohol doesn't put a dent in it, nor does acetone. For a graphic
illustration of this, try cleaning something greasy or oily in each. It
is a fire hazard, but not as much so as gasoline, which we use regularly
in much greater volumes and even more dangerous circumstances. Filling
up your car is an accident waiting to happen. You have a large volume
of extremely volatile and extremely flammable fuel with an enclosed
space above it containing a mixture of the volatile fumes and air. One
spark and the fireworks begin. Yes there is some danger if it is
handled carelessly, but as woodworkers we handle volatile flammable
materials all the time, so I assumed everyone was with the program of
not setting their work area on fire.

On Mon, 30 May 2005 10:57:19 -0500, Hax Planx
wrote:

Unfortunately, nothing compares to naphtha for cleaning up grease and
oil and just because you can't see any doesn't mean it isn't there.
Alcohol doesn't put a dent in it, nor does acetone. For a graphic
illustration of this, try cleaning something greasy or oily in each

No mean-spiritedness intended here, but really, if you have THAT much
grease on your work, you need another hobby. I've often gone not even
close to that extent [using alcohol] and had absolutely no problems
finishing whatsoever.

Guess who wrote:

On Mon, 30 May 2005 10:57:19 -0500, Hax Planx
wrote:

Unfortunately, nothing compares to naphtha for cleaning up grease and
oil and just because you can't see any doesn't mean it isn't there.
Alcohol doesn't put a dent in it, nor does acetone. For a graphic
illustration of this, try cleaning something greasy or oily in each

No mean-spiritedness intended here, but really, if you have THAT much
grease on your work, you need another hobby. I've often gone not even
close to that extent [using alcohol] and had absolutely no problems
finishing whatsoever.

What type of finishes do you typically use?

And, the advice of Hax isn't directed at the amount but the almost
insane reactions against using anything that some see as the least bit
flammable/toxic/whatever...

Yeah, don't smoke while using naptha and don't sniff the can opening,
but it's a common shop consumable, for heaven's sake!

I finish 90% of my projects with shellac and thus find that a wipedown
with denatured alcohol kills two birds with one stone. For those who
don't know, denatured alcohol is the solvent in shellac, and thus both
removes dust and helps prepare for the finish.