Load bearing beams
Hi,
I've read thru recent posts (titles mainly), but not found anything relating directly to my question: I want to put two beams in the garage strong enough to hang a shell of a car from. The shell should weigh in at 1/2 ton max, and I would like to hang it from the centre of the beam (worst case). The beam should be run left/right and so the span should be about 10' There are no walls to place the beams on, so they will have to be on posts. I am planning on using the garage walls to prevent the arrangement from left/right movement, and braceing along the walls between the posts to prevent forward/backwards movement, but I plan to lift the car with a chain block at each end, so there should be no load in either of these directions. So is there anything inheriently wrong with my plan? What thickness of wood should I be looking for to support 1/2 ton, centrally from a 10' span? Cheers Will |
Load bearing beams
"William Munns" wrote in message
... Hi, I've read thru recent posts (titles mainly), but not found anything relating directly to my question: I want to put two beams in the garage strong enough to hang a shell of a car from. The shell should weigh in at 1/2 ton max, and I would like to hang it from the centre of the beam (worst case). The beam should be run left/right and so the span should be about 10' There are no walls to place the beams on, so they will have to be on posts. I am planning on using the garage walls to prevent the arrangement from left/right movement, and braceing along the walls between the posts to prevent forward/backwards movement, but I plan to lift the car with a chain block at each end, so there should be no load in either of these directions. So is there anything inheriently wrong with my plan? What thickness of wood should I be looking for to support 1/2 ton, centrally from a 10' span? Cheers Will Could you not use two metal box section A frames with block and tackle? Jon |
Load bearing beams
"Jon" wrote in
: "William Munns" wrote in message ... ... Could you not use two metal box section A frames with block and tackle? Jon The plan is to winch it up there, then rachet strap it to the beam (in addition to the winch), and use the space underneth. |
Load bearing beams
"William Munns" wrote in message
... "Jon" wrote in : "William Munns" wrote in message ... ... Could you not use two metal box section A frames with block and tackle? Jon The plan is to winch it up there, then rachet strap it to the beam (in addition to the winch), and use the space underneth. Are you planning on keeping the shell suspended for some time? Do you intend to walk below the suspended shell? Jon |
Load bearing beams
"Jon" wrote in news:c4ufjr$m6b$1
@thorium.cix.co.uk: Are you planning on keeping the shell suspended for some time? Yes, 6 months Do you intend to walk below the suspended shell? /s/walk/work yes, thats kinda the point! |
Load bearing beams
"William Munns" wrote in message
... "Jon" wrote in news:c4ufjr$m6b$1 @thorium.cix.co.uk: Are you planning on keeping the shell suspended for some time? Yes, 6 months Do you intend to walk below the suspended shell? /s/walk/work yes, thats kinda the point! If that was me underneath it, I'd want it supported on stands as well as being strapped up. Jon |
Load bearing beams
William Munns wrote in message ... Hi, I've read thru recent posts (titles mainly), but not found anything relating directly to my question: I want to put two beams in the garage strong enough to hang a shell of a car from. The shell should weigh in at 1/2 ton max, and I would like to hang it from the centre of the beam (worst case). The beam should be run left/right and so the span should be about 10' There are no walls to place the beams on, so they will have to be on posts. I am planning on using the garage walls to prevent the arrangement from left/right movement, and braceing along the walls between the posts to prevent forward/backwards movement, but I plan to lift the car with a chain block at each end, so there should be no load in either of these directions. So is there anything inheriently wrong with my plan? What thickness of wood should I be looking for to support 1/2 ton, centrally from a 10' span? I would then use an 8" RSJ supported by an A frame on each side made out of 4" square tube. You suggest hanging the car from one central point, I would be concerned that this approach could buckle the roof, I would support the car from two points directly above each side! |
Load bearing beams
Someone gave me a link to joists but I saved it on a browser that went
the way of all flesh recently. Searh for joists. The span will give you the loading. I think 7 x 2's should do but you could bolt a pair together to be certain they are faily cheap. If you can select your ow choose straight timber with few or no knots. Certainly no large dead knotts in the centre. You aught to make a framework up to act as bracing. I wouldn't want to advise you on that. -- Posted via Mailgate.ORG Server - http://www.Mailgate.ORG |
Load bearing beams
William Munns wrote
Hi, but I plan to lift the car with a chain block at each end, so there should be no load in either of these directions. So is there anything inheriently wrong with my plan? Yes What thickness of wood should I be looking for to support 1/2 ton, centrally from a 10' span? Forget wood, use steel box section. Seek out a steel fabricator if you can't MIG weld. HTH Paul. |
Load bearing beams
"Stuart" wrote in
: William Munns wrote in message ... Hi, I've read thru recent posts (titles mainly), but not found anything relating directly to my question: I want to put two beams in the garage strong enough to hang a shell of a car from. The shell should weigh in at 1/2 ton max, and I would like to hang it from the centre of the beam (worst case). The beam should be run left/right and so the span should be about 10' There are no walls to place the beams on, so they will have to be on posts. I am planning on using the garage walls to prevent the arrangement from left/right movement, and braceing along the walls between the posts to prevent forward/backwards movement, but I plan to lift the car with a chain block at each end, so there should be no load in either of these directions. So is there anything inheriently wrong with my plan? What thickness of wood should I be looking for to support 1/2 ton, centrally from a 10' span? I would then use an 8" RSJ supported by an A frame on each side made out of 4" square tube. You suggest hanging the car from one central point, I would be concerned that this approach could buckle the roof, I would support the car from two points directly above each side! Sorry I wasn't very clear, I plan to have two such beams, one at the rear and one at the front of the car, and I plan to put a chain hoist on each beam, and split the load further down the chain onto the front spring mounts at the back, and the chassis rails at the front. the 1/2 ton should be spread across the two beams, but I'd prefer each beam to be able to take the full weight. |
Load bearing beams
William Munns submitted this idea :
What thickness of wood should I be looking for to support 1/2 ton, centrally from a 10' span? Wood? I think a steel RSJ would be much more suitable as well as being of a more predictable load bearing strength. I have no idea of the size or how to calculate it, but obviously the deeper the RSJ, the thinner it can be. I would then think in terms of an A frame arrangement at either end of the beam to support it. These would be bolted to the walls so they can't move. What sort of walls do you have on the garage? -- -- Regards, Harry (M1BYT) (L) http://www.ukradioamateur.org |
All times are GMT +1. The time now is 06:47 PM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter