Home |
Search |
Today's Posts |
|
UK diy (uk.d-i-y) For the discussion of all topics related to diy (do-it-yourself) in the UK. All levels of experience and proficency are welcome to join in to ask questions or offer solutions. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
|
#1
|
|||
|
|||
Question about varnishing hard wood
Hello all,
I've been varnishing an old oak cabinet that we've had for years. I started out from scratch by sanding off all the old grunge back to the bare wood. I've applied several coats of varnish and it gives the appearance that the varnish is not evenly applied. That is, the darker grain seems to repel the varnish, whereas the lighter areas have taken the varnish no problem. To the touch, it feels as if the varnish layers consists of a series of tiny hills and troughs, instead of being evenly smooth. Should I have used some kind of primer or preparation before starting? Can I use it now, or do I have to restart from the bare wood. Many thanks, Paul -- -- -nospam Remove "-nospam" for real address |
#2
|
|||
|
|||
Question about varnishing hard wood
"Paul Moore" -nospam wrote in message ... Hello all, I've been varnishing an old oak cabinet that we've had for years. I started out from scratch by sanding off all the old grunge back to the bare wood. I've applied several coats of varnish and it gives the appearance that the varnish is not evenly applied. That is, the darker grain seems to repel the varnish, whereas the lighter areas have taken the varnish no problem. To the touch, it feels as if the varnish layers consists of a series of tiny hills and troughs, instead of being evenly smooth. Should I have used some kind of primer or preparation before starting? Can I use it now, or do I have to restart from the bare wood. Many thanks, Paul I've had this effect recently with old oak, which I think (from its colour) was American red oak, and while using acrillic varnish. The varnish seemed to raise the open grain much more than the closed grain in between. I wonder whether you rubbed down between coats? When you get this effect it seems to help if you rub down between each coat, rather than just after the first. Additionally you may need more coats than usual, having sealed the open grain with the first two or three.... Charles F |
#3
|
|||
|
|||
Question about varnishing hard wood
Paul Moore wrote in message ... Hello all, I've been varnishing an old oak cabinet that we've had for years. I started out from scratch by sanding off all the old grunge back to the bare wood. I've applied several coats of varnish and it gives the appearance that the varnish is not evenly applied. That is, the darker grain seems to repel the varnish, whereas the lighter areas have taken the varnish no problem. To the touch, it feels as if the varnish layers consists of a series of tiny hills and troughs, instead of being evenly smooth. Should I have used some kind of primer or preparation before starting? Can I use it now, or do I have to restart from the bare wood. If we're talking polyurethane varnish, it sands well so I'd flatten it with a 180 grit on an orbital sander and then by hand with a fine paper. Lastly, wipe a *thin* coat of varnish on with a rag. It sounds like you've simply put too much on and not rubbed down between coats. |
#4
|
|||
|
|||
Question about varnishing hard wood
varnish is not evenly applied. That is, the darker grain seems
to repel the varnish, whereas the lighter areas have taken the varnish no problem. You must rub down with a fine sandpaper between coats (no coarser than 150 grit). I tend to run down the first coat and the penultimate coat using an orbital, which I find tends to leave less marks than other methods. I usually put on a very thick first coat and rely on the sander to flatten off the high bits. Christian. |
#5
|
|||
|
|||
Question about varnishing hard wood
With real wood such as OAK you get a far superior finish with oil,s
such as Danish Oil. Strip off and oil if you can bear it! EC |
#6
|
|||
|
|||
Question about varnishing hard wood
|
#7
|
|||
|
|||
Question about varnishing hard wood
In article 0,
Mike Ring wrote: Can't say I'm convinced about Danish oil. I tried it on my kitchen window sills (cills? internal widow boards? and it was very dark, althogh the colour of the oil was light. I wanted it to pick up the colur of my light oak floor. The effect will depend on the wood. Danish oil does not appreciably darken pine for eg. With all finishes it is advisable to test a portion first for the desired effect. I'm at present plucking up courage to use matt polyurethane Yuck. If you want a matt finish why not wax it? Peter -- Peter Ashby School of Life Sciences, University of Dundee, Scotland To assume that I speak for the University of Dundee is to be deluded. Reverse the Spam and remove to email me. |
#8
|
|||
|
|||
Question about varnishing hard wood
Peter Ashby wrote in
news I'm at present plucking up courage to use matt polyurethane Yuck. If you want a matt finish why not wax it? Peter Because being kitchen windowsills they're bound to be abused by stuff being put on them detergent bottles, etc, which may mark them. Or is wax proof against that - and is there a sort of initial applicatin wax as against lokking after it wax? If so I'll give it a try mike r |
#9
|
|||
|
|||
Question about varnishing hard wood
In article 0,
Mike Ring wrote: Because being kitchen windowsills they're bound to be abused by stuff being put on them detergent bottles, etc, which may mark them. Or is wax proof against that - and is there a sort of initial applicatin wax as against lokking after it wax? If so I'll give it a try No, you will have to look after it. Mind you when the matt poly starts looking bad you will have more work to do to renew it as a finish. Have you thought about using a tougher varnish and matting it down once its dried? Peter -- Peter Ashby School of Life Sciences, University of Dundee, Scotland To assume that I speak for the University of Dundee is to be deluded. Reverse the Spam and remove to email me. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Floating wood floor. | UK diy | |||
wood laminate flooring | UK diy | |||
Bending Wood ? | UK diy | |||
Glow-Worm 30Ci & bypass question | UK diy |