| Page 1 of 2 | 1 | 2 |
|
|
Measuring liquid level in a distant tank
On Tue, 07 Jun 2016 14:46:59 +0100, jim wrote:
Isuppose an oil watchman type thing would do the job but they're £60 minimum, and I don't need wireless comms, would prefer "off" until "on for level check" to save power/batts. The 6ft tall c.1200 litre tank is the other side of a wall from where the gauge reading c/would be done, and it contains water. Essentially I want to know when the tank is being over depleted. It should refill constantly but if there's a supply issue, measuring (even roughly) the level in the tank is the easiest way to detect that issue and deal with it promptly before the tank is emptied. Being able to check that it is full in the morning /last thing would be sufficient I suppose... Any ideas anyone? TIA Is running a small pipe through the wall then vertical clear pipe up the wall too simple? Main problem would be periods of sub zero temperatures. Cheers Dave R -- Windows 8.1 on PCSpecialist box |
Measuring liquid level in a distant tank
On Tue, 7 Jun 2016 14:46:59 +0100 (GMT+01:00), jim k wrote:
Isuppose an oil watchman type thing would do the job but they're £60 minimum, and I don't need wireless comms, would prefer "off" until "on for level check" to save power/batts. The 6ft tall c.1200 litre tank is the other side of a wall from where the gauge reading c/would be done, and it contains water. Essentially I want to know when the tank is being over depleted. It should refill constantly but if there's a supply issue, measuring (even roughly) the level in the tank is the easiest way to detect that issue and deal with it promptly before the tank is emptied. Being able to check that it is full in the morning /last thing would be sufficient I suppose... Any ideas anyone? http://uk.farnell.com/triton-control...ble/dp/7064263 http://uk.farnell.com/triton-control...713-pd-r2-acce http://www.farnell.com/datasheets/316999.pdf http://www.farnell.com/datasheets/34724.pdf One small hole in the top of the tank, sealed by a suitable gland, any power supply from a couple of AA's to mains and a suitable lamp / led Easily adjustable trigger point level in a matter of seconds. Will work 'forever' -- |
Measuring liquid level in a distant tank
Isuppose an oil watchman type thing would do the job but they're
£60 minimum, and I don't need wireless comms, would prefer "off" until "on for level check" to save power/batts. The 6ft tall c.1200 litre tank is the other side of a wall from where the gauge reading c/would be done, and it contains water. Essentially I want to know when the tank is being over depleted. It should refill constantly but if there's a supply issue, measuring (even roughly) the level in the tank is the easiest way to detect that issue and deal with it promptly before the tank is emptied. Being able to check that it is full in the morning /last thing would be sufficient I suppose... Any ideas anyone? TIA -- Jim K ----Android NewsGroup Reader---- http://usenet.sinaapp.com/ |
Measuring liquid level in a distant tank
On Tue, 7 Jun 2016 15:33:37 +0100 (GMT+01:00), jim k wrote:
Mmm thanks Mike, if I read the bumf right the float just dangles by the cable from the roof of the tank? The weight pulls the cable down and the position of the float relative to the weight turns the switch on/off? Yes, that's more or less it:) The key thing is no need for electronics, no holes below the level of the fluid / in the wall of the tank, no pivots to seize up, a switch that will easily last a few hundred thousand operations and everything is sealed. It's a fit and forget solution. -- |
Measuring liquid level in a distant tank
The Other Mike Wrote in message:
On Tue, 7 Jun 2016 14:46:59 +0100 (GMT+01:00), jim k wrote: Isuppose an oil watchman type thing would do the job but they're £60 minimum, and I don't need wireless comms, would prefer "off" until "on for level check" to save power/batts. The 6ft tall c.1200 litre tank is the other side of a wall from where the gauge reading c/would be done, and it contains water. Essentially I want to know when the tank is being over depleted. It should refill constantly but if there's a supply issue, measuring (even roughly) the level in the tank is the easiest way to detect that issue and deal with it promptly before the tank is emptied. Being able to check that it is full in the morning /last thing would be sufficient I suppose... Any ideas anyone? http://uk.farnell.com/triton-control...ble/dp/7064263 http://uk.farnell.com/triton-control...713-pd-r2-acce http://www.farnell.com/datasheets/316999.pdf http://www.farnell.com/datasheets/34724.pdf One small hole in the top of the tank, sealed by a suitable gland, any power supply from a couple of AA's to mains and a suitable lamp / led Easily adjustable trigger point level in a matter of seconds. Will work 'forever' Mmm thanks Mike, if I read the bumf right the float just dangles by the cable from the roof of the tank? The weight pulls the cable down and the position of the float relative to the weight turns the switch on/off? -- Jim K ----Android NewsGroup Reader---- http://usenet.sinaapp.com/ |
Measuring liquid level in a distant tank
David Wrote in message:
On Tue, 07 Jun 2016 14:46:59 +0100, jim wrote: Isuppose an oil watchman type thing would do the job but they're £60 minimum, and I don't need wireless comms, would prefer "off" until "on for level check" to save power/batts. The 6ft tall c.1200 litre tank is the other side of a wall from where the gauge reading c/would be done, and it contains water. Essentially I want to know when the tank is being over depleted. It should refill constantly but if there's a supply issue, measuring (even roughly) the level in the tank is the easiest way to detect that issue and deal with it promptly before the tank is emptied. Being able to check that it is full in the morning /last thing would be sufficient I suppose... Any ideas anyone? TIA Is running a small pipe through the wall then vertical clear pipe up the wall too simple? Main problem would be periods of sub zero temperatures. Cheers Dave R Hi Dave, Mmm that's probably the simplest but I think also the fewer holes in the tank the better :-) -- Jim K ----Android NewsGroup Reader---- http://usenet.sinaapp.com/ |
Measuring liquid level in a distant tank
On 07/06/16 14:46, jim wrote:
I suppose an oil watchman type thing would do the job but they're £60 minimum, and I don't need wireless comms, would prefer "off" until "on for level check" to save power/batts. The 6ft tall c.1200 litre tank is the other side of a wall from where the gauge reading c/would be done, and it contains water. Essentially I want to know when the tank is being over depleted. It should refill constantly but if there's a supply issue, measuring (even roughly) the level in the tank is the easiest way to detect that issue and deal with it promptly before the tank is emptied. Being able to check that it is full in the morning /last thing would be sufficient I suppose... Any ideas anyone? transparent plastic pipe through a hole in that wall? i.e remote sight glass. TIA -- Truth welcomes investigation because truth knows investigation will lead to converts. It is deception that uses all the other techniques. |
Measuring liquid level in a distant tank
On Tue, 7 Jun 2016 15:50:38 +0100 (GMT+01:00), jim wrote:
Is running a small pipe through the wall then vertical clear pipe up the wall too simple? I like that as well, KISS. Main problem would be periods of sub zero temperatures. But hadn't thought of that one... Mmm that's probably the simplest but I think also the fewer holes in the tank the better :-) Doesn't need another hole in the tank, just T into the outlet pipe? Freezing would be a problem, the float switch is also pretty KISS, until ice forms on the surface of the water but that won't happen as much as a small bore pipe freezing. -- Cheers Dave. |
Measuring liquid level in a distant tank
"Dave Liquorice" Wrote in message:
On Tue, 7 Jun 2016 15:50:38 +0100 (GMT+01:00), jim wrote: Is running a small pipe through the wall then vertical clear pipe up the wall too simple? I like that as well, KISS. Main problem would be periods of sub zero temperatures. But hadn't thought of that one... Mmm that's probably the simplest but I think also the fewer holes in the tank the better :-) Doesn't need another hole in the tank, just T into the outlet pipe? Mmm the tank outlet is 1" pipe too... Freezing shouldn't be an issue as it's all inside. I think Mike's float valve idea is ahead so far, I found a better pdf about the triton unit and it seems it can indicate 2 states (with suitable wiring and leds maybe? It should last a long time on batteries?) depending on the angle of the float within the tank, and the position of the weight relative to the float and "top water level" I think :-D Some buggering about maybe but could be a neat setup... -- Jim K ----Android NewsGroup Reader---- http://usenet.sinaapp.com/ |
Measuring liquid level in a distant tank
"jim" k wrote in message
o.uk... "Dave Liquorice" Wrote in message: On Tue, 7 Jun 2016 15:50:38 +0100 (GMT+01:00), jim wrote: Is running a small pipe through the wall then vertical clear pipe up the wall too simple? I like that as well, KISS. Main problem would be periods of sub zero temperatures. But hadn't thought of that one... Mmm that's probably the simplest but I think also the fewer holes in the tank the better :-) Doesn't need another hole in the tank, just T into the outlet pipe? Mmm the tank outlet is 1" pipe too... Freezing shouldn't be an issue as it's all inside. I think Mike's float valve idea is ahead so far, I found a better pdf about the triton unit and it seems it can indicate 2 states (with suitable wiring and leds maybe? It should last a long time on batteries?) depending on the angle of the float within the tank, and the position of the weight relative to the float and "top water level" I think :-D Some buggering about maybe but could be a neat setup... You could do it cheaper with two SP vertical float switches (note that they are not float valves not switches - float valves let or stop water entering a tank) fastened to a stick (say a piece of left over rigid plasic pipe). eg one of Hong Kongs finest :-) http://www.ebay.co.uk/itm/SP/172215750390? If you are not in a rush for delivery. But it gives you an idea of what to google for if you want a cheaper option. -- Adam |
Measuring liquid level in a distant tank
"jim" k wrote in message
o.uk... "ARW" Wrote in message: "jim" k wrote in message o.uk... "Dave Liquorice" Wrote in message: On Tue, 7 Jun 2016 15:50:38 +0100 (GMT+01:00), jim wrote: Is running a small pipe through the wall then vertical clear pipe up the wall too simple? I like that as well, KISS. Main problem would be periods of sub zero temperatures. But hadn't thought of that one... Mmm that's probably the simplest but I think also the fewer holes in the tank the better :-) Doesn't need another hole in the tank, just T into the outlet pipe? Mmm the tank outlet is 1" pipe too... Freezing shouldn't be an issue as it's all inside. I think Mike's float valve idea is ahead so far, I found a better pdf about the triton unit and it seems it can indicate 2 states (with suitable wiring and leds maybe? It should last a long time on batteries?) depending on the angle of the float within the tank, and the position of the weight relative to the float and "top water level" I think :-D Some buggering about maybe but could be a neat setup... You could do it cheaper with two SP vertical float switches (note that they are not float valves not switches - float valves let or stop water entering a tank) Yes you're correct :-) oops! fastened to a stick (say a piece of left over rigid plasic pipe). eg one of Hong Kongs finest :-) http://www.ebay.co.uk/itm/SP/172215750390? That's a horizontal one but I get the idea I think... If you are not in a rush for delivery. But it gives you an idea of what to google for if you want a cheaper option. Two vertical float switches on a stick would suggest at least one (the lower one) would be totally submerged in the tank? Are they upto that? On the eBay link they seem to have a threaded "panel mounting" end to them where the wires emerge? I'll have another look. -- Adam |
Measuring liquid level in a distant tank
"ARW" Wrote in message:
"jim" k wrote in message o.uk... "Dave Liquorice" Wrote in message: On Tue, 7 Jun 2016 15:50:38 +0100 (GMT+01:00), jim wrote: Is running a small pipe through the wall then vertical clear pipe up the wall too simple? I like that as well, KISS. Main problem would be periods of sub zero temperatures. But hadn't thought of that one... Mmm that's probably the simplest but I think also the fewer holes in the tank the better :-) Doesn't need another hole in the tank, just T into the outlet pipe? Mmm the tank outlet is 1" pipe too... Freezing shouldn't be an issue as it's all inside. I think Mike's float valve idea is ahead so far, I found a better pdf about the triton unit and it seems it can indicate 2 states (with suitable wiring and leds maybe? It should last a long time on batteries?) depending on the angle of the float within the tank, and the position of the weight relative to the float and "top water level" I think :-D Some buggering about maybe but could be a neat setup... You could do it cheaper with two SP vertical float switches (note that they are not float valves not switches - float valves let or stop water entering a tank) Yes you're correct :-) oops! fastened to a stick (say a piece of left over rigid plasic pipe). eg one of Hong Kongs finest :-) http://www.ebay.co.uk/itm/SP/172215750390? That's a horizontal one but I get the idea I think... If you are not in a rush for delivery. But it gives you an idea of what to google for if you want a cheaper option. Two vertical float switches on a stick would suggest at least one (the lower one) would be totally submerged in the tank? Are they upto that? On the eBay link they seem to have a threaded "panel mounting" end to them where the wires emerge? However I just seen they can be longer and have 2 switches, lower and upper.... 500 mm might work but the water level in the tank doesn?t get as close to top of the tank (and so mounting point) as the top float switch in the ones I've seen so far... Thanks though Adam, I'll look further into them. -- Jim K ----Android NewsGroup Reader---- http://usenet.sinaapp.com/ |
Measuring liquid level in a distant tank
Any ideas anyone? I know you said no electronics but there is an Instructable for a project using an Arduino and a cheap ultrasonic sensor: http://www.instructables.com/id/Meas...asonic-sensor/ |
Measuring liquid level in a distant tank
"ARW" wrote in message
... I'll have another look. I belive you are correct However you can get similar switches as to the one Mike suggested on ebay a lot cheaper. How critical is the device?. -- Adam |
Measuring liquid level in a distant tank
On 07/06/2016 20:21, Lee wrote:
Any ideas anyone? I know you said no electronics but there is an Instructable for a project using an Arduino and a cheap ultrasonic sensor: http://www.instructables.com/id/Meas...asonic-sensor/ A length of plastic pipe, an end cap, a couple or more reed switches and a magnet on a float sliding up and down the pipe? |
Measuring liquid level in a distant tank
Lee Wrote in message:
Any ideas anyone? I know you said no electronics but there is an Instructable for a project using an Arduino and a cheap ultrasonic sensor: http://www.instructables.com/id/Meas...asonic-sensor/ Yeah, thanks Lee, I pondered briefly looking into something along those lines but whilst it would eventually be an interesting project, I think my arduino/pi skills are not really upto doing it in a sensible timeframe :-) Also it would be mains and wifi dependent and I quite like the KISS battery powered visual approach. -- Jim K ----Android NewsGroup Reader---- http://usenet.sinaapp.com/ |
Measuring liquid level in a distant tank
"ARW" Wrote in message:
"ARW" wrote in message ... I'll have another look. I belive you are correct However you can get similar switches as to the one Mike suggested on ebay a lot cheaper. How critical is the device?. If the tank empties then it takes priority over pretty much any/everything until it's fixed & starts refilling.... :-) -- Jim K ----Android NewsGroup Reader---- http://usenet.sinaapp.com/ |
Measuring liquid level in a distant tank
jim wrote:
I suppose an oil watchman type thing would do the job but they're £60 minimum, and I don't need wireless comms, would prefer "off" until "on for level check" to save power/batts. The 6ft tall c.1200 litre tank is the other side of a wall from where the gauge reading c/would be done, and it contains water. Essentially I want to know when the tank is being over depleted. It should refill constantly but if there's a supply issue, measuring (even roughly) the level in the tank is the easiest way to detect that issue and deal with it promptly before the tank is emptied. Being able to check that it is full in the morning /last thing would be sufficient I suppose... Any ideas anyone? TIA A sensitive pressure gauge installed at the tap end should do the job by measuring the head of water. Would only work when the tap is shut. You "might" get enough adjustment range out of a washing machine water level sensor. Older machines will probably have ones with adjustment screws and you could add extra spring pressure to measure a few feet rather than the usual few inches in a WM application. Would work with battery, light and push to read on a KISS principle. |
Measuring liquid level in a distant tank
Thanks Brian. You got me with the electronics idea, I'm not savvy enough! Other idea, is a simple float and lever on the spindle of a pot which is part of a bridge circuit driving a plus or minus meter. -- Jim K ----Android NewsGroup Reader---- http://usenet.sinaapp.com/ |
Measuring liquid level in a distant tank
On Tuesday, 7 June 2016 20:22:02 UTC+1, Lee wrote:
Any ideas anyone? I know you said no electronics but there is an Instructable for a project using an Arduino and a cheap ultrasonic sensor: http://www.instructables.com/id/Meas...asonic-sensor/ Talk about doing it the hard way. This is a beginner bulb & battery level electronics exercise. Did you get that lightswitch wired in yet? NT |
Measuring liquid level in a distant tank
jim wrote:
Bob Minchin Wrote in message: jim wrote: I suppose an oil watchman type thing would do the job but they're £60 minimum, and I don't need wireless comms, would prefer "off" until "on for level check" to save power/batts. The 6ft tall c.1200 litre tank is the other side of a wall from where the gauge reading c/would be done, and it contains water. Essentially I want to know when the tank is being over depleted. It should refill constantly but if there's a supply issue, measuring (even roughly) the level in the tank is the easiest way to detect that issue and deal with it promptly before the tank is emptied. Being able to check that it is full in the morning /last thing would be sufficient I suppose... Any ideas anyone? TIA A sensitive pressure gauge installed at the tap end should do the job by measuring the head of water. Would only work when the tap is shut. Er no. The output of the tank is pumped so pressure at any taps would be independent of tank water level... until there's no water to pump so no pressure. Doh! I did not know that vital bit of info. Until then I thought it was a neat solution! |
Measuring liquid level in a distant tank
Bob Minchin Wrote in message:
jim wrote: I suppose an oil watchman type thing would do the job but they're £60 minimum, and I don't need wireless comms, would prefer "off" until "on for level check" to save power/batts. The 6ft tall c.1200 litre tank is the other side of a wall from where the gauge reading c/would be done, and it contains water. Essentially I want to know when the tank is being over depleted. It should refill constantly but if there's a supply issue, measuring (even roughly) the level in the tank is the easiest way to detect that issue and deal with it promptly before the tank is emptied. Being able to check that it is full in the morning /last thing would be sufficient I suppose... Any ideas anyone? TIA A sensitive pressure gauge installed at the tap end should do the job by measuring the head of water. Would only work when the tap is shut. Er no. The output of the tank is pumped so pressure at any taps would be independent of tank water level... until there's no water to pump so no pressure. -- Jim K ----Android NewsGroup Reader---- http://usenet.sinaapp.com/ |
Measuring liquid level in a distant tank
Bob Minchin Wrote in message:
jim wrote: Bob Minchin Wrote in message: jim wrote: I suppose an oil watchman type thing would do the job but they're £60 minimum, and I don't need wireless comms, would prefer "off" until "on for level check" to save power/batts. The 6ft tall c.1200 litre tank is the other side of a wall from where the gauge reading c/would be done, and it contains water. Essentially I want to know when the tank is being over depleted. It should refill constantly but if there's a supply issue, measuring (even roughly) the level in the tank is the easiest way to detect that issue and deal with it promptly before the tank is emptied. Being able to check that it is full in the morning /last thing would be sufficient I suppose... Any ideas anyone? TIA A sensitive pressure gauge installed at the tap end should do the job by measuring the head of water. Would only work when the tap is shut. Er no. The output of the tank is pumped so pressure at any taps would be independent of tank water level... until there's no water to pump so no pressure. Doh! I did not know that vital bit of info. Until then I thought it was a neat solution! How much is a gauge anyway? Might look a bit unusual sticking out me worktop :-) -- Jim K |
Measuring liquid level in a distant tank
jim wrote:
Bob Minchin Wrote in message: jim wrote: Bob Minchin Wrote in message: jim wrote: I suppose an oil watchman type thing would do the job but they're £60 minimum, and I don't need wireless comms, would prefer "off" until "on for level check" to save power/batts. The 6ft tall c.1200 litre tank is the other side of a wall from where the gauge reading c/would be done, and it contains water. Essentially I want to know when the tank is being over depleted. It should refill constantly but if there's a supply issue, measuring (even roughly) the level in the tank is the easiest way to detect that issue and deal with it promptly before the tank is emptied. Being able to check that it is full in the morning /last thing would be sufficient I suppose... Any ideas anyone? TIA A sensitive pressure gauge installed at the tap end should do the job by measuring the head of water. Would only work when the tap is shut. Er no. The output of the tank is pumped so pressure at any taps would be independent of tank water level... until there's no water to pump so no pressure. Doh! I did not know that vital bit of info. Until then I thought it was a neat solution! How much is a gauge anyway? Might look a bit unusual sticking out me worktop :-) Should only be a few quid on fleabay and the washing machine sensor can be robbed from a defunct machine for nought and tucked well out of the way. |
Measuring liquid level in a distant tank
|
Measuring liquid level in a distant tank
Lee Wrote in message:
On 08/06/2016 13:48, wrote: Talk about doing it the hard way. This is a beginner bulb & battery level electronics exercise. Depends on you POV, the author already wrote the code and (clone) 'Duinos and the sensor used are dirt cheap. Plus it met both the "push to read" and actual water level remit :) Did you get that lightswitch wired in yet? If that was directed at me, what lightswitch? It tends be rather 'hit n miss' these days ;-) -- Jim K |
Measuring liquid level in a distant tank
On Wednesday, 8 June 2016 20:06:05 UTC+1, Lee wrote:
On 08/06/2016 13:48, tabbypurr wrote: Talk about doing it the hard way. This is a beginner bulb & battery level electronics exercise. Depends on you POV, the author already wrote the code and (clone) 'Duinos and the sensor used are dirt cheap. Plus it met both the "push to read" and actual water level remit :) It can be done easily for nothing with household electronic scraps. Arduinos aren't that cheap. And no, I won't be telling Jim how. If he thinks he knows what he's doing he can figure it out or not. Did you get that lightswitch wired in yet? If that was directed at me, what lightswitch? No, Jim. He made that job far harder that it need be too. NT |
Measuring liquid level in a distant tank
On Thursday, 9 June 2016 07:56:42 UTC+1, jim wrote:
tabbypurr Wrote in message: On Wednesday, 8 June 2016 20:06:05 UTC+1, Lee wrote: On 08/06/2016 13:48, tabbypurr wrote: Talk about doing it the hard way. This is a beginner bulb & battery level electronics exercise. Depends on you POV, the author already wrote the code and (clone) 'Duinos and the sensor used are dirt cheap. Plus it met both the "push to read" and actual water level remit :) It can be done easily for nothing with household electronic scraps. Arduinos aren't that cheap. And no, I won't be telling Jim how. If he thinks he knows what he's doing he can figure it out or not. Good, I wouldn't trust any of your "advice" nige, you imagine it all up - to make yourself feel more important I guess... Did you get that lightswitch wired in yet? If that was directed at me, what lightswitch? No, Jim. He made that job far harder that it need be too. Er? Sounds like more blathering on... NT My my you're a grumpy old ****wit today nige ;-) pretty much the dumb response I expected. If you were almost anyone else I'd explain how they can be done. |
Measuring liquid level in a distant tank
|
Measuring liquid level in a distant tank
On 08/06/2016 15:57, Bob Minchin wrote:
jim wrote: Bob Minchin Wrote in message: jim wrote: I suppose an oil watchman type thing would do the job but they're £60 minimum, and I don't need wireless comms, would prefer "off" until "on for level check" to save power/batts. The 6ft tall c.1200 litre tank is the other side of a wall from where the gauge reading c/would be done, and it contains water. Essentially I want to know when the tank is being over depleted. It should refill constantly but if there's a supply issue, measuring (even roughly) the level in the tank is the easiest way to detect that issue and deal with it promptly before the tank is emptied. Being able to check that it is full in the morning /last thing would be sufficient I suppose... Any ideas anyone? TIA A sensitive pressure gauge installed at the tap end should do the job by measuring the head of water. Would only work when the tap is shut. Er no. The output of the tank is pumped so pressure at any taps would be independent of tank water level... until there's no water to pump so no pressure. Doh! I did not know that vital bit of info. Until then I thought it was a neat solution! I would expect the pump to only run when it detects a flow and I very much doubt that there would be any residual pressure from the pump when there isn't any flow. Peter |
Measuring liquid level in a distant tank
|
Measuring liquid level in a distant tank
Peter Andrews Wrote in message:
On 08/06/2016 15:57, Bob Minchin wrote: jim wrote: Bob Minchin Wrote in message: jim wrote: I suppose an oil watchman type thing would do the job but they're £60 minimum, and I don't need wireless comms, would prefer "off" until "on for level check" to save power/batts. The 6ft tall c.1200 litre tank is the other side of a wall from where the gauge reading c/would be done, and it contains water. Essentially I want to know when the tank is being over depleted. It should refill constantly but if there's a supply issue, measuring (even roughly) the level in the tank is the easiest way to detect that issue and deal with it promptly before the tank is emptied. Being able to check that it is full in the morning /last thing would be sufficient I suppose... Any ideas anyone? TIA A sensitive pressure gauge installed at the tap end should do the job by measuring the head of water. Would only work when the tap is shut. Er no. The output of the tank is pumped so pressure at any taps would be independent of tank water level... until there's no water to pump so no pressure. Doh! I did not know that vital bit of info. Until then I thought it was a neat solution! I would expect the pump to only run when it detects a flow and I very much doubt that there would be any residual pressure from the pump when there isn't any flow. Peter Sorry Peter, in this case you'd be wrong ;-) -- Jim K |
Measuring liquid level in a distant tank
On Thursday, 9 June 2016 13:40:25 UTC+1, jim wrote:
tabbypurr Wrote in message: On Thursday, 9 June 2016 07:56:42 UTC+1, jim wrote: tabbypurr Wrote in message: On Wednesday, 8 June 2016 20:06:05 UTC+1, Lee wrote: On 08/06/2016 13:48, tabbypurr wrote: Talk about doing it the hard way. This is a beginner bulb & battery level electronics exercise. Depends on you POV, the author already wrote the code and (clone) 'Duinos and the sensor used are dirt cheap. Plus it met both the "push to read" and actual water level remit :) It can be done easily for nothing with household electronic scraps. Arduinos aren't that cheap. And no, I won't be telling Jim how. If he thinks he knows what he's doing he can figure it out or not. Good, I wouldn't trust any of your "advice" nige, you imagine it all up - to make yourself feel more important I guess... Did you get that lightswitch wired in yet? If that was directed at me, what lightswitch? No, Jim. He made that job far harder that it need be too. Er? Sounds like more blathering on... NT My my you're a grumpy old ****wit today nige ;-) pretty much the dumb response I expected. If you were almost anyone else I'd explain how they can be done. Ooh the regret... not. Still you've managed to carefully avoid embarrassing yourself with more ****wittering so probably for the best ;-) You don't get to know how to do it, but you get to mouth off immaturely. I can live with that. NT |
Measuring liquid level in a distant tank
|
Measuring liquid level in a distant tank
|
Measuring liquid level in a distant tank
"jim" k wrote in message
o.uk... Wrote in message: On 08/06/2016 23:45, wrote: On Wednesday, 8 June 2016 20:06:05 UTC+1, Lee wrote: On 08/06/2016 13:48, tabbypurr wrote: Talk about doing it the hard way. This is a beginner bulb & battery level electronics exercise. Depends on you POV, the author already wrote the code and (clone) 'Duinos and the sensor used are dirt cheap. Plus it met both the "push to read" and actual water level remit :) It can be done easily for nothing with household electronic scraps. Arduinos aren't that cheap. And no, I won't be telling Jim how. If he thinks he knows what he's doing he can figure it out or not. Did you get that lightswitch wired in yet? If that was directed at me, what lightswitch? No, Jim. He made that job far harder that it need be too. NT Sigh, another interesting thread degenerating into a waste of space because of willy waving - c'mon chaps, nothing is gained by this. Agreed. ??? You are supposed to say "he started it - not me":-) -- Adam |
Measuring liquid level in a distant tank
Wrote in message:
On 08/06/2016 23:45, wrote: On Wednesday, 8 June 2016 20:06:05 UTC+1, Lee wrote: On 08/06/2016 13:48, tabbypurr wrote: Talk about doing it the hard way. This is a beginner bulb & battery level electronics exercise. Depends on you POV, the author already wrote the code and (clone) 'Duinos and the sensor used are dirt cheap. Plus it met both the "push to read" and actual water level remit :) It can be done easily for nothing with household electronic scraps. Arduinos aren't that cheap. And no, I won't be telling Jim how. If he thinks he knows what he's doing he can figure it out or not. Did you get that lightswitch wired in yet? If that was directed at me, what lightswitch? No, Jim. He made that job far harder that it need be too. NT Sigh, another interesting thread degenerating into a waste of space because of willy waving - c'mon chaps, nothing is gained by this. Agreed. -- Jim K |
Measuring liquid level in a distant tank
"ARW" Wrote in message:
"jim" k wrote in message o.uk... Wrote in message: On 08/06/2016 23:45, wrote: On Wednesday, 8 June 2016 20:06:05 UTC+1, Lee wrote: On 08/06/2016 13:48, tabbypurr wrote: Talk about doing it the hard way. This is a beginner bulb & battery level electronics exercise. Depends on you POV, the author already wrote the code and (clone) 'Duinos and the sensor used are dirt cheap. Plus it met both the "push to read" and actual water level remit :) It can be done easily for nothing with household electronic scraps. Arduinos aren't that cheap. And no, I won't be telling Jim how. If he thinks he knows what he's doing he can figure it out or not. Did you get that lightswitch wired in yet? If that was directed at me, what lightswitch? No, Jim. He made that job far harder that it need be too. NT Sigh, another interesting thread degenerating into a waste of space because of willy waving - c'mon chaps, nothing is gained by this. Agreed. ??? You are supposed to say "he started it - not me":-) I felt a strangely appropriate need to mix up the script :-D -- Jim K |
Measuring liquid level in a distant tank
On Thursday, 9 June 2016 17:52:35 UTC+1, wrote:
On 08/06/2016 23:45, tabbypurr wrote: On Wednesday, 8 June 2016 20:06:05 UTC+1, Lee wrote: On 08/06/2016 13:48, tabbypurr wrote: Talk about doing it the hard way. This is a beginner bulb & battery level electronics exercise. Depends on you POV, the author already wrote the code and (clone) 'Duinos and the sensor used are dirt cheap. Plus it met both the "push to read" and actual water level remit :) It can be done easily for nothing with household electronic scraps. Arduinos aren't that cheap. And no, I won't be telling Jim how. If he thinks he knows what he's doing he can figure it out or not. Did you get that lightswitch wired in yet? If that was directed at me, what lightswitch? No, Jim. He made that job far harder that it need be too. Sigh, another interesting thread degenerating into a waste of space because of willy waving - c'mon chaps, nothing is gained by this. I accept Jim thinks I'm as clueless as he is, and don't care. Idiots always think everyone else is equally idiotic. No, I'll stop there. In fact I won't come back to read his reply. There is nothing constructive to add. |
| All times are GMT +1. The time now is 07:41 PM. |
|
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter