Home |
Search |
Today's Posts |
|
UK diy (uk.d-i-y) For the discussion of all topics related to diy (do-it-yourself) in the UK. All levels of experience and proficency are welcome to join in to ask questions or offer solutions. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to uk.d-i-y
|
|||
|
|||
Auto air valve failed, again!
On Jun 3, 6:16*pm, "MuddyMike" wrote:
Our five year old Mexico HE36 gas boiler needs yet another auto air vent valve. It was replaced in the final months of warranty due to it leaking and dribbling water onto the electrics causing the trip to go. Parts Centre are the only stockist I can find that have one, and one only! Is in the Portsmouth branch but they are sending it up to me "next day" delivery for four quid postage. That's not bad as it would have cost more then that in diesel for me to have driven to the nearest branch Anyone else aware of this being a regular failure on these boilers? Mike Honeywell do a version with a screw down cap which has a fibre washer. With the cap open the valve will vent air from the system. Once clear screw the cap down and if any air/hydrogen does accumulate it opens the valve and collects under the cap. This causes the fibre washer to dry out and shrink, allowing the air to escape. If fluid reches the fibre washer it expands again and closes off the vent. Another option is to extend the air discharge point via a tube to somewhere safe. Then any minor weep will not cause damage to your electrics. Unless you have a problem elsewhere the air vent should not be needed after a couple of weeks as all the air should have left the system. |
#2
Posted to uk.d-i-y
|
|||
|
|||
Auto air valve failed, again!
On Jun 3, 10:05*pm, cynic wrote:
.. Unless you have a problem elsewhere the air vent should not be needed after a couple of weeks as all the air should have left the system. Yes, it's a regular point of failure on any AAV. They should only be used to get the air out after filling and then the cap screwed down. If more air accumulates, there is a problem somewhere; automatic air venting should not be needed. There was one design (expensive ISTR) that had the air release valve above the float and connected by a linkage, the idea being the mucky water didn't get near the valve. |
#3
Posted to uk.d-i-y
|
|||
|
|||
Auto air valve failed, again!
This is the valve.
http://share.ovi.com/media/Muddymike...uddymike.10804 I have plugged the leak with the set screw and nut you see in the top, Bit fuzzy that picture, must check before uploading in future. Mike |
#4
Posted to uk.d-i-y
|
|||
|
|||
Auto air valve failed, again!
On Sat, 04 Jun 2011 13:08:34 +0100, MuddyMike wrote:
This is the valve. http://share.ovi.com/media/Muddymike...uddymike.10804 If that's an Ideal Icos/Isar/I**** series the AAV is going to be the least of your worries ;-/ -- John Stumbles -- http://yaph.co.uk Eagles may soar, but weasels don't get sucked into jet engines. |
#5
Posted to uk.d-i-y
|
|||
|
|||
Auto air valve failed, again!
"YAPH" wrote in message ... On Sat, 04 Jun 2011 13:08:34 +0100, MuddyMike wrote: This is the valve. http://share.ovi.com/media/Muddymike...uddymike.10804 If that's an Ideal Icos/Isar/I**** series the AAV is going to be the least of your worries ;-/ No its £2000 worth of Mexico HE36, not without trouble mind :-( Mike |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|