Re-Fit Radiator
 

Hi all

The kichen saga continues..
The kitchen radiator was long since removed, to give access for wiring
chases etc.
It was moved to the garage probably 4-6 months ago.
Although the inlet/outlet ports were covered, it is likely that some rust
has formed inside the rad.

Due to slow progress and the likelihood of colder weather, I am considering
re-fitting the rad to take the chill off.
This would also allow testing of the new feed piping I am working on for a
kick space heater.

So, is there anything that can be done to "rinse out any rust" from the
radiator before re-fitting?
It is not an old tatty thing - moderish stelrad type bog-standard item.

Thanks

Phil

Re-Fit Radiator
 

In message ,
TheScullster writes
Hi all

The kichen saga continues..
The kitchen radiator was long since removed, to give access for wiring
chases etc.
It was moved to the garage probably 4-6 months ago.
Although the inlet/outlet ports were covered, it is likely that some rust
has formed inside the rad.

Due to slow progress and the likelihood of colder weather, I am considering
re-fitting the rad to take the chill off.
This would also allow testing of the new feed piping I am working on for a
kick space heater.

So, is there anything that can be done to "rinse out any rust" from the
radiator before re-fitting?
It is not an old tatty thing - moderish stelrad type bog-standard item.

Thanks

Assuming your cold water pressure is reasonable, connect a hosepipe to
each port (alternately, and several times), and give it a good blasting
until the emerging water is clear?
--
Ian

Re-Fit Radiator
 

In message , Ian Jackson
writes
In message ,
TheScullster writes
Hi all

The kichen saga continues..
The kitchen radiator was long since removed, to give access for wiring
chases etc.
It was moved to the garage probably 4-6 months ago.
Although the inlet/outlet ports were covered, it is likely that some rust
has formed inside the rad.

Due to slow progress and the likelihood of colder weather, I am considering
re-fitting the rad to take the chill off.
This would also allow testing of the new feed piping I am working on for a
kick space heater.

So, is there anything that can be done to "rinse out any rust" from the
radiator before re-fitting?
It is not an old tatty thing - moderish stelrad type bog-standard item.

Thanks

Assuming your cold water pressure is reasonable, connect a hosepipe to
each port (alternately, and several times), and give it a good blasting
until the emerging water is clear?

Thinking about it further, I believe that various 'colas' contain
phosphoric acid - the active ingredient in de-rusting materials like
'Kurerust'. They can be used to remove surface contamination and
corrosion from metals. You might like to experiment with a piece of
rusty metal.

If it works, to really get rid of all the internal surface rust, you
could try filling the radiator with a bottle of cola. Make sure you use
the 'Real Thing'! ;o))

http://webcache.googleusercontent.co...7xsKeAJ:en.wik
ipedia.org/wiki/Coca-Cola+coke+phosphoric+acid&cd=1&hl=en&ct=clnk&gl=uk

--
Ian

Re-Fit Radiator
 

"TheScullster" wrote...

Hi all

The kichen saga continues..
The kitchen radiator was long since removed, to give access for wiring
chases etc.
It was moved to the garage probably 4-6 months ago.
Although the inlet/outlet ports were covered, it is likely that some rust
has formed inside the rad.

Due to slow progress and the likelihood of colder weather, I am
considering re-fitting the rad to take the chill off.
This would also allow testing of the new feed piping I am working on for a
kick space heater.

So, is there anything that can be done to "rinse out any rust" from the
radiator before re-fitting?
It is not an old tatty thing - moderish stelrad type bog-standard item.


Plug one end, stand on that end, fill with cheap cola and leave for a
weekend, the phosphoric acid in it will dissolve the rust and passivate the
inside surface with iron phosphate in its place? Then rinse until the kids
can't drink any more... ;)

Dave H
--
(The engineer formerly known as Homeless)

"Rules are for the obedience of fools, and the guidance of wise men" -
Douglas Bader

Re-Fit Radiator
 

On 05/11/2010 12:12, Dave H. wrote:
"TheScullster" wrote...

Hi all

The kichen saga continues..
The kitchen radiator was long since removed, to give access for wiring
chases etc.
It was moved to the garage probably 4-6 months ago.
Although the inlet/outlet ports were covered, it is likely that some rust
has formed inside the rad.

Due to slow progress and the likelihood of colder weather, I am
considering re-fitting the rad to take the chill off.
This would also allow testing of the new feed piping I am working on for a
kick space heater.

So, is there anything that can be done to "rinse out any rust" from the
radiator before re-fitting?
It is not an old tatty thing - moderish stelrad type bog-standard item.


Plug one end, stand on that end, fill with cheap cola and leave for a
weekend, the phosphoric acid in it will dissolve the rust and passivate the
inside surface with iron phosphate in its place? Then rinse until the kids
can't drink any more... ;)

Dave H
Are you supposed to publish the recipe for irn bru?
;-)

Re-Fit Radiator
 

"Dave H." wrote

"TheScullster" wrote...

Hi all

The kichen saga continues..
The kitchen radiator was long since removed, to give access for wiring
chases etc.
It was moved to the garage probably 4-6 months ago.
Although the inlet/outlet ports were covered, it is likely that some rust
has formed inside the rad.

Due to slow progress and the likelihood of colder weather, I am
considering re-fitting the rad to take the chill off.
This would also allow testing of the new feed piping I am working on for
a kick space heater.

So, is there anything that can be done to "rinse out any rust" from the
radiator before re-fitting?
It is not an old tatty thing - moderish stelrad type bog-standard item.


Plug one end, stand on that end, fill with cheap cola and leave for a
weekend, the phosphoric acid in it will dissolve the rust and passivate
the inside surface with iron phosphate in its place? Then rinse until the
kids can't drink any more... ;)

Dave H

Sounds interesting, but what effect/reaction does any residual Cola or iron
phosphate have with system inhibitors etc.?

Phil