Hi,

trivial question but Google is being unhelpful.

Our newly installed bath is nice and level - which means that any splashing
from the power shower onto the edge of the bath is distributed evenly
between the tile side and the floor side.

Next time (hah) I think I will put a very slight slope towards the wall (at
the risk of a slightly skew tile line at the bath ends) to ensure that all
the water drains to the tile side.

Not wishing to un-tile to adjust the legs on the bath, I need a very small
ridge along the floor side of the top edge of the bath (if you follow me) to
dissuade the water from trickling over.

Some kind of strip, white rubber or similar, which could be fitted using
silicone sealant.

I have seen various (not very attractive) plastic right angles for sealing
between the bath and tiles and I don't really want a wide plastic strip as I
think it would look ugly.

A nice half oval strip of white flexible rubber would be nice.

^ strip
-------- bath side top
| | bath outside


Hope the dodgy ASCII art explains.

Anyone come across such stuff, or another suitable alternative?

TIA
Dave R
--

David W.E. Roberts wrote:
Hi,

trivial question but Google is being unhelpful.

Our newly installed bath is nice and level - which means that any
splashing from the power shower onto the edge of the bath is
distributed evenly between the tile side and the floor side.
Normal people would use a shower curtain or bath screen to stop the water
going on the floor :-)

"BillR" wrote in message
...
David W.E. Roberts wrote:
Hi,

trivial question but Google is being unhelpful.

Our newly installed bath is nice and level - which means that any
splashing from the power shower onto the edge of the bath is
distributed evenly between the tile side and the floor side.
Normal people would use a shower curtain or bath screen to stop the water
going on the floor :-)

Ho ho ha ha bloody ha.

David W.E. Roberts wrote:
"BillR" wrote in message
...
David W.E. Roberts wrote:
Hi,

trivial question but Google is being unhelpful.

Our newly installed bath is nice and level - which means that any
splashing from the power shower onto the edge of the bath is
distributed evenly between the tile side and the floor side.
Normal people would use a shower curtain or bath screen to stop the
water going on the floor :-)

Ho ho ha ha bloody ha.
Have I misunderstood? you have a power shower over a bath without shower
curtain or screen and you want to put a strip of plastic along the bath edge
to encourage the water not to go on the floor?

BillR wrote:

Have I misunderstood? you have a power shower over a bath without shower
curtain or screen and you want to put a strip of plastic along the bath edge
to encourage the water not to go on the floor?

Well, it works on Design Wars :-)

Only seen snatches of it, but didn't somebody say, "They could
have put up a shower curtain"? There was also an aside about
trouble with the hot water - bet they didn't put in a bigger tank
for that giant bath.

Chris
--
Chris J Dixon Nottingham UK


Have dancing shoes, will ceilidh.

"BillR" wrote in message
...
David W.E. Roberts wrote:
"BillR" wrote in message
...
David W.E. Roberts wrote:
Hi,

trivial question but Google is being unhelpful.

Our newly installed bath is nice and level - which means that any
splashing from the power shower onto the edge of the bath is
distributed evenly between the tile side and the floor side.
Normal people would use a shower curtain or bath screen to stop the
water going on the floor :-)

Ho ho ha ha bloody ha.
Have I misunderstood? you have a power shower over a bath without shower
curtain or screen and you want to put a strip of plastic along the bath
edge
to encourage the water not to go on the floor?

Ah!
Thought you were just being unhelpful and sarcastic at a time of travail.

Yes, I have (see previous posts e.g. Message-ID:

with subject Shower screen grumble...) worked out that if you have a power
shower the water does not stay in the area of the bath by some form of
arcane magic.

I now have a shower curtain (having been caught out by the pictures of
shower screens suggesting that they were much taller than in actuality).

A shower curtain keeps flying water in the bath area, and protects the
exposed (floor) side of the bath. As would a shower screen.

However it does not protect the tiled head of the bath (where the shower
head is) nor the tiled side of the bath nor some of the tiled end of the
bath.

Water runs down the tiles, or settles directly on the rim of the bath in
these areas.

Because the bath is level, the water on the rim can flow in all directions,
including towards the floor side of the bath, where it runs round the ends
of the shower curtain and down the the bath panel onto the floor.

My 'next time' fix would be to slope the bath towards the tiled wall a
little so any water on the rim ran inwards, then drained into the bath.

Being reluctant to hack off the tiles and re-slope the bath now, I am
looking for a neat alternative to stop water on the rim of the bath running
off the edge onto the floor.

Cloths placed at strategic locations, as long as regularly squeezed, can do
this but they are unsightly and can be forgotten by those not initiated into
arcane showering rituals.

I was looking for something which could be used to produce a slight ridge
(couple of mm would do) along the exposed edge of the bath so that any water
would run into the bath instead of down the bath panel.

Preferably white rubber for softness and the inconspicuous look.

Another response has pointed me to a 3M product (which I haven't located
yet).

Cheers
Dave R

David W.E. Roberts wrote:
"BillR" wrote in message
...
David W.E. Roberts wrote:
"BillR" wrote in message
...
David W.E. Roberts wrote:
Hi,

trivial question but Google is being unhelpful.

Our newly installed bath is nice and level - which means that any
splashing from the power shower onto the edge of the bath is
distributed evenly between the tile side and the floor side.
Normal people would use a shower curtain or bath screen to stop the
water going on the floor :-)

Ho ho ha ha bloody ha.
Have I misunderstood? you have a power shower over a bath without
shower curtain or screen and you want to put a strip of plastic
along the bath edge to encourage the water not to go on the floor?

Ah!
Thought you were just being unhelpful and sarcastic at a time of
travail.

Yes, I have (see previous posts e.g. Message-ID:

with subject Shower screen grumble...) worked out that if you have a
power shower the water does not stay in the area of the bath by some
form of arcane magic.

I now have a shower curtain (having been caught out by the pictures of
shower screens suggesting that they were much taller than in
actuality).
I hate shower screens after fitting an expensive on in my on-suite.

A shower curtain keeps flying water in the bath area, and protects the
exposed (floor) side of the bath. As would a shower screen.

However it does not protect the tiled head of the bath (where the
shower head is) nor the tiled side of the bath nor some of the tiled
end of the bath.

Water runs down the tiles, or settles directly on the rim of the bath
in these areas.

Because the bath is level, the water on the rim can flow in all
directions, including towards the floor side of the bath, where it
runs round the ends of the shower curtain and down the the bath panel
onto the floor.

My 'next time' fix would be to slope the bath towards the tiled wall a
little so any water on the rim ran inwards, then drained into the
bath.

Being reluctant to hack off the tiles and re-slope the bath now, I am
looking for a neat alternative to stop water on the rim of the bath
running off the edge onto the floor.

Cloths placed at strategic locations, as long as regularly squeezed,
can do this but they are unsightly and can be forgotten by those not
initiated into arcane showering rituals.
I guess your bath must have a very rounded top edge.
The new steel baths I fitted have quite a flat edge, they don't flex either.

"David W.E. Roberts" wrote:

Because the bath is level, the water on the rim can flow in all directions,
including towards the floor side of the bath, where it runs round the ends
of the shower curtain and down the the bath panel onto the floor.

My 'next time' fix would be to slope the bath towards the tiled wall a
little so any water on the rim ran inwards, then drained into the bath.

Being reluctant to hack off the tiles and re-slope the bath now, I am
looking for a neat alternative to stop water on the rim of the bath running
off the edge onto the floor.

Cloths placed at strategic locations, as long as regularly squeezed, can do
this but they are unsightly and can be forgotten by those not initiated into
arcane showering rituals.

I was looking for something which could be used to produce a slight ridge
(couple of mm would do) along the exposed edge of the bath so that any water
would run into the bath instead of down the bath panel.

I have seen in one of the catalogues, a white plastic, self-adhesive corner
piece. It attaches to the top edge of the tub, and the side of the
wall/enclosure, and is specifically designed to solve the problem you
describe.

Sheila