Hello,

I am looking to buy my first router. At the moment I anticipate only
using it for occasional DIY so I do not want to spend a fortune on it.
I'm sure once I've got the hang of it, I'll be using it all the time
and will want to upgrade to something better

For now though I was looking for an entry level router to learn with.
The cheapest at Screwfix is a Titan router, order code 31965. (Ok,
they actually do a cheaper one by Direct Power, but this is a 1/4"
collet and reading the DIY wiki faq it says 1/2" is stronger).

Has anyone got anything good or bad to say about this model?

Thanks.

In article , Fred
scribeth thus
Hello,

I am looking to buy my first router. At the moment I anticipate only
using it for occasional DIY so I do not want to spend a fortune on it.
I'm sure once I've got the hang of it, I'll be using it all the time
and will want to upgrade to something better

For now though I was looking for an entry level router to learn with.
The cheapest at Screwfix is a Titan router, order code 31965. (Ok,
they actually do a cheaper one by Direct Power, but this is a 1/4"
collet and reading the DIY wiki faq it says 1/2" is stronger).

Has anyone got anything good or bad to say about this model?

Thanks.

Dunno about that one but I bought a Trend some years ago, just the entry
level one and its been excellent:--)

Theres not a lot that hasn't been able to do including nip the end off
my middle finger!..

And just recently I've takes to milling bits of ally with it and thats a
fine old edge it makes on that too

Far better then that PPro heap of cack I bought from B&Q...
--
Tony Sayer

"tony sayer" wrote in message

Theres not a lot that hasn't been able to do including nip the end off
my middle finger!..

And just recently I've takes to milling bits of ally with it and thats a
fine old edge it makes on that too

Far better then that PPro heap of cack I bought from B&Q...
--
Tony Sayer



How the hell did you manage to nip the tip of your finger? the only way I
can see that happening if you stuck your finger in to stop the motor?

In article , George
scribeth thus

"tony sayer" wrote in message

Theres not a lot that hasn't been able to do including nip the end off
my middle finger!..

And just recently I've takes to milling bits of ally with it and thats a
fine old edge it makes on that too

Far better then that PPro heap of cack I bought from B&Q...
--
Tony Sayer



How the hell did you manage to nip the tip of your finger? the only way I
can see that happening if you stuck your finger in to stop the motor?




Just put it down as it was slowing down and managed to trip over the
bloody power cable and pulled it off the worktop and my big mitt was in
the way..so it wasn't going at all fast but still had a nip;!..
--
Tony Sayer

Fred wrote:
I am looking to buy my first router. At the moment I anticipate only
using it for occasional DIY so I do not want to spend a fortune on it.
I'm sure once I've got the hang of it, I'll be using it all the time
and will want to upgrade to something better

For now though I was looking for an entry level router to learn with.
The cheapest at Screwfix is a Titan router, order code 31965. (Ok,
they actually do a cheaper one by Direct Power, but this is a 1/4"
collet and reading the DIY wiki faq it says 1/2" is stronger).

Has anyone got anything good or bad to say about this model?

Not that one, but I did buy the £22ish 1/4" one from Screwfix, and must
say it has been totally reliable, and done whatever I ask of it.

I've found a great use for it is the routing of door hinge rebates - it
now takes less then 5 minutes to get a really neat, identical pair.
It is also good for the small rebate near the surface for mortice locks.
I used it yesterday to run a channel down the back of a length of
skirting board.

I'm not sure I would get a bigger one now, unless it was clamped into a
table - they are more powerful, with the temptation to go deeper, and
far more chance of a slip or jam of the cutter. I asked about one at a
woodworkers shop,for doing the full rebate cutout for mortice locks, but
was told off for even thinking about such a thing - they said to never
attempt such a deep cut with an handheld router, as they are too
unpredictable in use. When clamped up, with the workpiece also well
secured, there is then no problem, but typical DIYers do not have such
facilities, and think they can get away with it.

It all depends on what your intended use is for it.
Alan.
--
To reply by e-mail, change the ' + ' to 'plus'.

On Sat, 08 Dec 2007 13:42:01 GMT
Fred wrote:

Hello,

I am looking to buy my first router. At the moment I anticipate only
using it for occasional DIY so I do not want to spend a fortune on it.
I'm sure once I've got the hang of it, I'll be using it all the time
and will want to upgrade to something better

For now though I was looking for an entry level router to learn with.
The cheapest at Screwfix is a Titan router, order code 31965. (Ok,
they actually do a cheaper one by Direct Power, but this is a 1/4"
collet and reading the DIY wiki faq it says 1/2" is stronger).

Has anyone got anything good or bad to say about this model?

Thanks.

Titan did have a reputation for being robust, but I have no experience.

I bought an Elu 1/4" long ago (De Walt make it now, to lower standards)
- it's what got me hooked on woodwork, and moved me from DIY shelving,
through fitted furniture, to cabinets.

On the way I bought other routers, but the one I use most often is one
my dad gave me, a Black&Decker D4. It's made of plastic, has a 1/4
collet, and it's not a plunge router - about 1965 vintage I guess. For
little jobs it just the ticket.

So whatever you buy today, you are likely to add to it, and not replace
it. Like clamps, you can't have enough routers.

R.

TheOldFellow wrote:


So whatever you buy today, you are likely to add to it, and not
replace it. Like clamps, you can't have enough routers.


Oh aint that the truth :-)


--
Dave - The Medway Handyman
www.medwayhandyman.co.uk
01634 717930
07850 597257

Fred wrote:
Hello,

I am looking to buy my first router. At the moment I anticipate only
using it for occasional DIY so I do not want to spend a fortune on it.
I'm sure once I've got the hang of it, I'll be using it all the time
and will want to upgrade to something better

Have a look at the notes he

http://www.diyfaq.org.uk/powertools/router.htm

to get a feel for the class of machine you need for the jobs you have in
mind.

For now though I was looking for an entry level router to learn with.
The cheapest at Screwfix is a Titan router, order code 31965. (Ok,
they actually do a cheaper one by Direct Power, but this is a 1/4"
collet and reading the DIY wiki faq it says 1/2" is stronger).

1/2" *is* stronger, but also much bigger and heavier. Which you need
depends on the job you are doing (in reality you will probably need one
of each eventually)

Has anyone got anything good or bad to say about this model?

Its a tad low on power for a 1/2" router, and the minimum speed is too
fast for use with the larger cutter sizes you may want to use in a
router table.

Unless you have an urgent need to cut worktops, letterbox cutouts, or
stair strings, then I have a feeling you might be better of with a 1/4"
machine of similar power for general purpose work. It will be much
smaller and lighter and generally easier for many jobs.

--
Cheers,

John.

/================================================== ===============\
| Internode Ltd - http://www.internode.co.uk |
|-----------------------------------------------------------------|
| John Rumm - john(at)internode(dot)co(dot)uk |
\================================================= ================/

On Sat, 08 Dec 2007 19:12:00 +0000, John Rumm
wrote:

Have a look at the notes he

http://www.diyfaq.org.uk/powertools/router.htm

[snip]
1/2" *is* stronger, but also much bigger and heavier. Which you need
depends on the job you are doing (in reality you will probably need one
of each eventually)

Thanks. I had read the faq but I thought that since the Titan was able
to use 8mm, 1/4", and 1/2" collets it was quite versatile and saved me
buying one of each.

I think the 1/4" model weighs 3.6kg and this one weighs 5kg. Do you
notice the extra weight? Surely it is resting on whatever you are
working on?

Its a tad low on power for a 1/2" router, and the minimum speed is too
fast for use with the larger cutter sizes you may want to use in a
router table.

What power would you expect for a 1/2" router and what minimum and
maximum speeds would you want?

Thanks.

On Sat, 08 Dec 2007 19:49:12 GMT, Fred
wrote:

What power would you expect for a 1/2" router and what minimum and
maximum speeds would you want?

Thanks.


Sorry to add to my own post but for that matter what speeds would you
want on a 1/4" router?

Fred wrote:
On Sat, 08 Dec 2007 19:49:12 GMT, Fred
wrote:

What power would you expect for a 1/2" router and what minimum and
maximum speeds would you want?

Thanks.


Sorry to add to my own post but for that matter what speeds would you
want on a 1/4" router?

You don't have the clearance for the larger cutters with these, so the
lower speed limit is less critical. Most cuts would be done at 15K or
more. Something like a Trend T5 does 9000 - 27,000 rpm which is quite
impressive. (these have dropped in price quite a bit lately).

--
Cheers,

John.

/================================================== ===============\
| Internode Ltd - http://www.internode.co.uk |
|-----------------------------------------------------------------|
| John Rumm - john(at)internode(dot)co(dot)uk |
\================================================= ================/

Fred wrote:

1/2" *is* stronger, but also much bigger and heavier. Which you need
depends on the job you are doing (in reality you will probably need one
of each eventually)

Thanks. I had read the faq but I thought that since the Titan was able
to use 8mm, 1/4", and 1/2" collets it was quite versatile and saved me
buying one of each.

Most 1/2" machines will come with a collet adaptor to take 1/4" bits.
The 8mm is of less use on a 1/2" machine than it is on a 1/4" since
there are larger cutters than are available in 8mm shank but no 1/4".

I think the 1/4" model weighs 3.6kg and this one weighs 5kg. Do you
notice the extra weight? Surely it is resting on whatever you are
working on?

The better 1/4" one are usually 3kg or less. Sometimes it is resting on
what you are working on, and hence not a problem - however the size and
the balance of it can make it harder going for decorative work, or when
using it on vertical edges in situ when you are carrying the full weight.

Its a tad low on power for a 1/2" router, and the minimum speed is too
fast for use with the larger cutter sizes you may want to use in a
router table.

What power would you expect for a 1/2" router and what minimum and
maximum speeds would you want?

If you were looking at high end machines then 1500W would be ok (ish)
but something nearer 2kW would be more versatile. Often the budget
machines tend to dissipate more power in their gearboxes and bearings
etc, so the available mechanical power is less than the numbers suggest.
Having said that, this will only be an issue on work with big cutters
(e.g. panel rasing, or large moulding cutters etc), or on heavy cuts in
things like worktops.

For the largest cutters, the maximum speed can be as low as 9000 rpm. So
a range of 8000 - 20K+ is quite handy.

(Something like the Freud FT2000E is often considered a good general
purpose "big" router, that adapts well for use in a table. The nice big
fine height adjuster being easy to grab etc. - I notice however that not
as many places are stocking that now)


--
Cheers,

John.

/================================================== ===============\
| Internode Ltd - http://www.internode.co.uk |
|-----------------------------------------------------------------|
| John Rumm - john(at)internode(dot)co(dot)uk |
\================================================= ================/

On Sat, 08 Dec 2007 21:50:59 +0000, John Rumm
wrote:

If you were looking at high end machines then 1500W would be ok (ish)
but something nearer 2kW would be more versatile
[snip]
For the largest cutters, the maximum speed can be as low as 9000 rpm. So
a range of 8000 - 20K+ is quite handy.

I had a quick look at Screwfix, I know other stores exist but it was
handy to look at their web site; it seems that the £30 model is rated
11,000 to 26,000 rpm but the £70 Bosch version is only 10,000 to
26,000 rpm, so I think you have to spend over £100 before you get the
ideal range of speeds.

The Ryobi is £109 and does 8,000 to 23,000 rpm and the Trend (£119) is
"variable to 27,000 rpm", so does this mean it does any speed between
0 and 27,000?

These cost four times as much, and once I use one regularly might be a
sound investment but at the moment, I'm not sure I could justify that
price for the occasional job.

It seems the speed is controlled by a dial numbered one to six on most
of these, so how do you relate the number on the dial to the speed? Do
you just set it to one when using something big and six when using
something small?

Thanks.

"Fred" wrote in message
...
On Sat, 08 Dec 2007 21:50:59 +0000, John Rumm
wrote:

If you were looking at high end machines then 1500W would be ok (ish)
but something nearer 2kW would be more versatile
[snip]
For the largest cutters, the maximum speed can be as low as 9000 rpm. So
a range of 8000 - 20K+ is quite handy.

I had a quick look at Screwfix, I know other stores exist but it was
handy to look at their web site; it seems that the £30 model is rated
11,000 to 26,000 rpm but the £70 Bosch version is only 10,000 to
26,000 rpm, so I think you have to spend over £100 before you get the
ideal range of speeds.

The Ryobi is £109 and does 8,000 to 23,000 rpm and the Trend (£119) is
"variable to 27,000 rpm", so does this mean it does any speed between
0 and 27,000?

These cost four times as much, and once I use one regularly might be a
sound investment but at the moment, I'm not sure I could justify that
price for the occasional job.

It seems the speed is controlled by a dial numbered one to six on most
of these, so how do you relate the number on the dial to the speed? Do
you just set it to one when using something big and six when using
something small?

Thanks.

Go by the wattage and speed factor,if you look at the trend £119 its ony
850w this is only suitable for light work hence it variable 27,000rpm
You want the maximium wattage and variable speed for a variety of woods and
working time.

On Sat, 08 Dec 2007 13:42:01 GMT, Fred wrote:
Hello,

I am looking to buy my first router. At the moment I anticipate only
using it for occasional DIY so I do not want to spend a fortune on it.
I'm sure once I've got the hang of it, I'll be using it all the time
and will want to upgrade to something better

For now though I was looking for an entry level router to learn with.
The cheapest at Screwfix is a Titan router, order code 31965. (Ok,
they actually do a cheaper one by Direct Power, but this is a 1/4"
collet and reading the DIY wiki faq it says 1/2" is stronger).

Has anyone got anything good or bad to say about this model?

Thanks.

I'd suggest not getting s _first_ router that's too powerful. I've got
a little 'un that I use handheld and a big 'un that stays in a router
table. I've tried using the T9 handgeld[1], but it scares me - which is
probably not a bad thing.
I like the Trend range. They're more expensive but you can get lots of
accessories for them and it's the accessories that make a router so
useful.

BTW, you'll spend more on router bits than you will on the router.

Pete

[1] just noticed the typo, must've been thinking about the previous
poster who nipped the end of his finger - and how it could've been
much, much worse.

--
.................................................. .........................
.. never trust a man who, when left alone ...... Pete Lynch .
.. in a room with a tea cosy ...... Marlow, England .
.. doesn't try it on (Billy Connolly) .....................................