Home |
Search |
Today's Posts |
|
UK diy (uk.d-i-y) For the discussion of all topics related to diy (do-it-yourself) in the UK. All levels of experience and proficency are welcome to join in to ask questions or offer solutions. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
|
#1
Posted to uk.d-i-y
|
|||
|
|||
tying off a ring outlet
Hi again all,
Another quick electrical wiring question. I'm about to change the wiring on my boiler, so that the existing mains power source (which is on my kitchen's ring) is unused and hanging in the breeze. I am putting a blanking plate over where the cable to the boiler came from. Obviously it's not going to be acceptable to leave the wires just lying there. What is the correct way to isolate the wires so that they are not touching anything, is it ok to use a screw terminal block ? |
#2
Posted to uk.d-i-y
|
|||
|
|||
tying off a ring outlet
Geronimo W. Christ Esq wrote:
is it ok to use a screw terminal block ? Yes, as long as it's a 30A one, and it's protected behind the blank face plate so it still remains accessible in future. |
#3
Posted to uk.d-i-y
|
|||
|
|||
tying off a ring outlet
On Fri, 10 Nov 2006 18:13:17 UTC, Andy Burns
wrote: Geronimo W. Christ Esq wrote: is it ok to use a screw terminal block ? Yes, as long as it's a 30A one, and it's protected behind the blank face plate so it still remains accessible in future. Why a 30A one? Surelt it's best to use one that suits the size of the cable??? -- The information contained in this post is copyright the poster, and specifically may not be published in, or used by Avenue Supplies, http://avenuesupplies.co.uk |
#4
Posted to uk.d-i-y
|
|||
|
|||
tying off a ring outlet
Bob Eager wrote:
Why a 30A one? Because the title said "ring outlet" not "spur outlet" Surely it's best to use one that suits the size of the cable? Which would be 2.5 t+e for a ring, and thereby require 30A block, no? chances are the spur would still be in 2.5 t+e anyway ... |
#5
Posted to uk.d-i-y
|
|||
|
|||
tying off a ring outlet
On Sun, 12 Nov 2006 08:46:44 UTC, Andy Burns
wrote: Bob Eager wrote: Why a 30A one? Because the title said "ring outlet" not "spur outlet" Surely it's best to use one that suits the size of the cable? Which would be 2.5 t+e for a ring, and thereby require 30A block, no? chances are the spur would still be in 2.5 t+e anyway ... Yes, but 30A is a bit big for a single wire of that size. Better grip with 15A. -- The information contained in this post is copyright the poster, and specifically may not be published in, or used by Avenue Supplies, http://avenuesupplies.co.uk |
#6
Posted to uk.d-i-y
|
|||
|
|||
tying off a ring outlet
On 12 Nov 2006 13:53:34 GMT someone who may be "Bob Eager"
wrote this:- Which would be 2.5 t+e for a ring, and thereby require 30A block, no? chances are the spur would still be in 2.5 t+e anyway ... Yes, but 30A is a bit big for a single wire of that size. One might think so, if not aware of how to use them. Better grip with 15A. Why? Provided the connector is used properly the grip should be much the same in either case. However, if this is a spur disconnecting it at the other end would be advisable. Alternatively, a switched fused connection unit ready for some other gadget could be put on the spur. -- David Hansen, Edinburgh I will *always* explain revoked encryption keys, unless RIP prevents me http://www.opsi.gov.uk/acts/acts2000/00023--e.htm#54 |
#7
Posted to uk.d-i-y
|
|||
|
|||
tying off a ring outlet
In article ,
Geronimo W. Christ Esq wrote: Another quick electrical wiring question. I'm about to change the wiring on my boiler, so that the existing mains power source (which is on my kitchen's ring) is unused and hanging in the breeze. I am putting a blanking plate over where the cable to the boiler came from. Obviously it's not going to be acceptable to leave the wires just lying there. What is the correct way to isolate the wires so that they are not touching anything, is it ok to use a screw terminal block ? It will require different treatment if part of the ring or now an unused spur off it. If a spur, I'd disconnect at source. If the ring itself, use 30 amp connector blocks and insulate well. They must remain accessible via a cover, etc. -- *And don't start a sentence with a conjunction * Dave Plowman London SW To e-mail, change noise into sound. |
#8
Posted to uk.d-i-y
|
|||
|
|||
tying off a ring outlet
Dave Plowman (News) wrote:
It will require different treatment if part of the ring or now an unused spur off it. If a spur, I'd disconnect at source. If the ring itself, use 30 amp connector blocks and insulate well. They must remain accessible via a cover, etc. Thankyou Dave, and Andy. Looking at it, I'm pretty sure it is a spur (there's only one cable so I guess it's not a ring) but I don't want to remove it as it may be useful in the future. I'll put a connector block on it and wrap it with tape, and stick a blank plate on. Thanks again. |
#9
Posted to uk.d-i-y
|
|||
|
|||
tying off a ring outlet
On Fri, 10 Nov 2006 21:26:30 UTC, "Geronimo W. Christ Esq"
wrote: Dave Plowman (News) wrote: It will require different treatment if part of the ring or now an unused spur off it. If a spur, I'd disconnect at source. If the ring itself, use 30 amp connector blocks and insulate well. They must remain accessible via a cover, etc. Thankyou Dave, and Andy. Looking at it, I'm pretty sure it is a spur (there's only one cable so I guess it's not a ring) but I don't want to remove it as it may be useful in the future. I'll put a connector block on it and wrap it with tape, and stick a blank plate on. I assumed it was a spur, hence my comment about using a smaller connector block. 15A would be OK, and will match the wire size better. I'd forget the tape; it's inside a box that's screwed shut, same as any electrical accessory. It'll probably only go yucky and sticky. -- The information contained in this post is copyright the poster, and specifically may not be published in, or used by Avenue Supplies, http://avenuesupplies.co.uk |
#10
Posted to uk.d-i-y
|
|||
|
|||
tying off a ring outlet
Bob Eager wrote:
I assumed it was a spur, hence my comment about using a smaller connector block. 15A would be OK, and will match the wire size better. I'd forget the tape; it's inside a box that's screwed shut, same as any electrical accessory. It'll probably only go yucky and sticky. Thanks for that, Bob. |
#11
Posted to uk.d-i-y
|
|||
|
|||
tying off a ring outlet
In article ,
Geronimo W. Christ Esq wrote: Looking at it, I'm pretty sure it is a spur (there's only one cable so I guess it's not a ring) but I don't want to remove it as it may be useful in the future. I'll put a connector block on it and wrap it with tape, and stick a blank plate on. No need to remove it, but you could still disconnect where it's spurred off. Having live circuits going nowhere is bad practice, IMHO. -- *When cheese gets it's picture taken, what does it say? Dave Plowman London SW To e-mail, change noise into sound. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Switch controlling Bathroom Light, Fan, and Outlet | Home Repair | |||
GFCI outlet / automated sprinkler system that plugs in it | Home Ownership | |||
2-prong outlet, 3-prong p | Home Repair | |||
When is a ring circuit not a ring circuit? | UK diy | |||
Change ceiling outlet pull switch to wall switch? | Home Ownership |