Does a 22mm to 15mm elbow exist ?
Fitting new shower valve - the connections are perpendicular to a
vertical wall. The inlets are 15mm, supply is 22mm chased in the wall. Is there a reducing elbow available ? TIA |
Does a 22mm to 15mm elbow exist ?
On 11 Oct 2006 02:56:04 -0700, "David Sims" wrote:
Fitting new shower valve - the connections are perpendicular to a vertical wall. The inlets are 15mm, supply is 22mm chased in the wall. Is there a reducing elbow available ? TIA Dunno but if not could you use a reducing T and block off or cut off and block up the unwanted 22mm end . You can also get T's with one end reduced . OR Get a 22mm elbow and fit a reducer to 15mm in to one leg ..Would that do .? Stuart |
Does a 22mm to 15mm elbow exist ?
"David Sims" wrote in message oups.com... Fitting new shower valve - the connections are perpendicular to a vertical wall. The inlets are 15mm, supply is 22mm chased in the wall. Is there a reducing elbow available ? TIA Nothing to add to Stuart's post except if you haven't got one get the BES catalogue and see what's available. Note that some of the unusual tees are bl**dy expensive. Jim A |
Does a 22mm to 15mm elbow exist ?
Stuart wrote: Dunno but if not could you use a reducing T and block off or cut off and block up the unwanted 22mm end . You can also get T's with one end reduced . OR Get a 22mm elbow and fit a reducer to 15mm in to one leg ..Would that do .? Stuart Thanks for T idea that would work, bit pushed for space for elbow and reducer |
Does a 22mm to 15mm elbow exist ?
On 11 Oct 2006 02:56:04 -0700, "David Sims" wrote:
|Fitting new shower valve - the connections are perpendicular to a |vertical wall. The inlets are 15mm, supply is 22mm chased in the wall. | |Is there a reducing elbow available ? Try your local plumber's merchant. Ours is very good on that sort of thing. -- Dave Fawthrop dave hyphenologist co uk Google Groups is IME the *worst* method of accessing usenet. GG subscribers would be well advised get a newsreader, say Agent, and a newsserver, say news.individual.net. These will allow them: to see only *new* posts, a killfile, and other goodies. |
Does a 22mm to 15mm elbow exist ?
Get a 22mm elbow and fit a reducer to 15mm in to one leg ..Would that do
.? Better would be a 15mm elbow and the reducer on the wall, rather than shower side. It is lower profile that way. Christian. |
Does a 22mm to 15mm elbow exist ?
On Wed, 11 Oct 2006 13:56:44 +0100, "Christian McArdle"
wrote: Get a 22mm elbow and fit a reducer to 15mm in to one leg ..Would that do .? Better would be a 15mm elbow and the reducer on the wall, rather than shower side. It is lower profile that way. Christian. But if the supply pipe is 22mm that wouldn't be a reducer would it .It would be an increaser ? |
Does a 22mm to 15mm elbow exist ?
David Sims wrote:
Fitting new shower valve - the connections are perpendicular to a vertical wall. The inlets are 15mm, supply is 22mm chased in the wall. Is there a reducing elbow available ? Being bored I actually went to the BES web site and looked. They have a reducing 22mm to 15mm compression fitting elbow, part number 17692, -- Chris Green |
Does a 22mm to 15mm elbow exist ?
Being bored I actually went to the BES web site and looked.
They have a reducing 22mm to 15mm compression fitting elbow, part number 17692, Normally, though, you want a solder fitting, as these take less room. Christian. |
Does a 22mm to 15mm elbow exist ?
On Wed, 11 Oct 2006 11:22:52 +0100, Stuart wrote:
Get a 22mm elbow and fit a reducer to 15mm in to one leg That's the approach I've taken for similar fittings in the past. Also for reducing T's. It's often cheaper to use a bog standard fitting + reducer than to mess about with rarely used items. Also since the reduced fits internally on the 22mm side it doesn't extend the fitting much. If length really is an issue it's possible to shorten the reducer and one of the legs of the elbow a few mm using a wheel cutter. |
Does a 22mm to 15mm elbow exist ?
|
Does a 22mm to 15mm elbow exist ?
On 11 Oct 2006 02:56:04 -0700, "David Sims" wrote:
Fitting new shower valve - the connections are perpendicular to a vertical wall. The inlets are 15mm, supply is 22mm chased in the wall. Is there a reducing elbow available ? Yes - they're widely used for sparge pipes in urinals, where the horizontal run from bay to bay is in 22mm and the downcomer is 15mm. -- Frank Erskine |
Does a 22mm to 15mm elbow exist ?
The message
from Frank Erskine contains these words: Yes - they're widely used for sparge pipes in urinals, where the horizontal run from bay to bay is in 22mm and the downcomer is 15mm. See, that's where a dodgy prostate gets you - plenty of time to look at the fittings. -- Skipweasel Pay no attention to that man behind the curtain. |
Does a 22mm to 15mm elbow exist ?
On Wed, 11 Oct 2006 18:11:22 +0100, Guy King
wrote: The message from Frank Erskine contains these words: Yes - they're widely used for sparge pipes in urinals, where the horizontal run from bay to bay is in 22mm and the downcomer is 15mm. See, that's where a dodgy prostate gets you - plenty of time to look at the fittings. :-) Actually a proper sparge pipe is fitted with cap ends and has holes drilled along its length, for a continuous trough. I was thinking of the feed to several stalls from the flushing cistern. -- Frank Erskine |
Does a 22mm to 15mm elbow exist ?
"David Sims" wrote in message ups.com... Stuart wrote: Dunno but if not could you use a reducing T and block off or cut off and block up the unwanted 22mm end . You can also get T's with one end reduced . OR Get a 22mm elbow and fit a reducer to 15mm in to one leg ..Would that do .? Stuart Thanks for T idea that would work, bit pushed for space for elbow and reducer There are tyees with 22mm end and two 15mm on the others. Use one of these with an "internal" 15mm cap to save space. |
Does a 22mm to 15mm elbow exist ?
On 11 Oct 2006 03:32:10 -0700, David Sims wrote:
Get a 22mm elbow and fit a reducer to 15mm in to one leg .. Thanks for T idea that would work, bit pushed for space for elbow and reducer A T will be much bigger that a 22m elbow and reducer. The reducer fits *inside* one end of the elbow making that connection 15mm instead of 22. -- Cheers Dave. pam is missing e-mail |
Does a 22mm to 15mm elbow exist ?
In article om, Dave
Liquorice writes On 11 Oct 2006 03:32:10 -0700, David Sims wrote: Get a 22mm elbow and fit a reducer to 15mm in to one leg .. Thanks for T idea that would work, bit pushed for space for elbow and reducer A T will be much bigger that a 22m elbow and reducer. The reducer fits *inside* one end of the elbow making that connection 15mm instead of 22. That doesn't sound right Dave, Ts with a reduced branch, solder or bsp or mix will usually stick out much less, the full size elbow has to turn in the greater size making it stick out more even before the reducer is taken into account. -- fred Plusnet - I hope you like vanilla |
Does a 22mm to 15mm elbow exist ?
On Wed, 11 Oct 2006 22:16:57 GMT, fred wrote:
A T will be much bigger that a 22m elbow and reducer. The reducer fits *inside* one end of the elbow making that connection 15mm instead of 22. That doesn't sound right Dave, Ts with a reduced branch, But have the full non-reduced branch as well... OK prehaps burried in the wall but is another "joint" that could leak. -- Cheers Dave. pam is missing e-mail |
Does a 22mm to 15mm elbow exist ?
"David Sims" wrote in message oups.com... Fitting new shower valve - the connections are perpendicular to a vertical wall. The inlets are 15mm, supply is 22mm chased in the wall. Is there a reducing elbow available ? Try B&Q Alan TIA |
All times are GMT +1. The time now is 06:40 PM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter