Home |
Search |
Today's Posts |
|
UK diy (uk.d-i-y) For the discussion of all topics related to diy (do-it-yourself) in the UK. All levels of experience and proficency are welcome to join in to ask questions or offer solutions. |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to uk.d-i-y
|
|||
|
|||
Garage power supply - Recap [Longish]
I participated in (but didn't initiate) the thread back in June - from which
I learned quite a lot - but have a few more questions. My detached double garage is currently being built, and is about 1.1 metres from the house. I intend to use a garage consumer unit - probably http://tinyurl.com/zmmh4, which I intend to connect to a spare way in my domestic CU. This currently has a 6mm^2 T&E cable connected to it, which was originally intended for an electric shower - but we used stored water and a shower pump instead - so this way and cable (with a suitable MCB) can be re-deployed. The 6mm^2 cable ends (with a couple of feet spare) just above the ceiling of an en-suite bathroom - more or less vertically above the point where the house end of the garage connection needs to be. I intend to join some 6mm^2 SWA cable to this cable, and take it through the wall and down the outside of the house, and across a passage door frame into the garage. Although the garage consumer unit can handle 40 amps, this is more than I need (and the sum of the individual MCBs is a lot less than this anyway) so I intend to use a 32 amp Type-B MCB at the house end of the connection - which seems more appropriate than a higher value if relying on the 2.5mm^2 earth within the existing T&E cable. My questions concern earthing arrangements, and physically joining the cables together. From my description of my incoming mains back in June, Andy Wade thought that I have a TN-S system, and David Hansen thought it was more likely TN-C-S. In case it helps, I've posted a photo of the main fuse and meter connection at http://www.mills37.plus.com/Incoming_mains.JPG Just to remind you, I estimate that I have about 10 metres of T&E, and will need about 6 metres of SWA. The options for earthing appear to be as follows: * Use 3-core SWA cable, and use one core (6 mm^2) as the earth - and join it onto the end of the T&E's 2.5mm^2 protective earth conductor - thus exporting the earth from the domestic CU * Use 2-core SWA, and use the steel armour as an earth, again joined to the T&E's earth conductor - again exporting the earth. [There will be no external connections to be subjected to 'weather', so corrosion shouldn't be a problem] * Use 2-core SWA and an earth spike at the garage end - thus providing the garage with its own earth - independent of the house supply * Some combination of the above. [Is there a down side to exporting the earth *and* having an earth spike?] I would welcome constructive comments on the relative merits of each of the above options - plus identification of any viable options I may have missed. Now to joining the cables . . The most convenient solution would be to have the joint inside a deep (metal) socket box high on the wall of the en-suite bathroom - sunk into the blockwork, and covered by a flush blanking plate. The T&E would come down from above, and be chased into the plaster and the SWA would go straight out through the wall from the back of the box - with its gland fitted to a knock-out in the box. Does anyone see any problems with this? How should I physically join the cables? Is a large chocolate block connector (inside the box) ok - or is there anything purpose-made which would be better? Do I need to earth the SWA's armour even if it isn't being used as the protective earth? Your expert advice will be much appreciated. Oh, and in case anyone mentions Part P - I think that what I am doing is probably covered by Part P. AIUI, extending an existing radial circuit isn't, but when you start taking it outside, it is. The building itself is exempt from building regs, being a detached garage of less than 30 M^2 floor area, and meeting the other exemption conditions. My inclination therefore is to forget about Part P and hope that it gets lost in the noise when the property is eventually sold (hopefully far into the future). Nevertheless, I want to ensure that I end up with a 'safe' electrical installation - hence the questions. -- Cheers, Roger ______ Email address maintained for newsgroup use only, and not regularly monitored.. Messages sent to it may not be read for several weeks. PLEASE REPLY TO NEWSGROUP! |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Sony GDM-FW900 power supply MCZ3001D info needed | Electronics Repair | |||
Tektronix 3001GPX Power supply info needed | Electronics Repair | |||
Wanted: Someone to examine switchmode power supply... | Electronics Repair | |||
Metal Working Machinery New and Used in Australia and for Export | Metalworking | |||
Switching Power Supply Failure | Electronics Repair |