Getting cables under the floorboards
 

I would like to pass some cables across a downstairs room under the
floorboards. The last time I did this I lifted some floorboards in the
corners of the room, and shoved some plastic rods through with string
attached, pulling cables through with string and leaving the string there
when I finished. I'm going from different places this time, so can't use the
string. It was a bit of a faff though, so I wondered if anyone has any tips
for making the job easier, or what tools to use, etc.

Peter.

Getting cables under the floorboards
 

It was a bit of a faff though, so I wondered if anyone has any tips
for making the job easier, or what tools to use, etc.

Well, I use garden cane and twine. I've heard of people using toy guns
firing some sort of projectile attached to some despooled thread. This can
be used to pull through the string and then the cable.

If the ground below is smooth, I've even heard of cheap radio controlled
cars, a mirror and a torch being used in a similar manner. I doubt either
method would handle sleeper walls well.

Christian.

Getting cables under the floorboards
 

"Christian McArdle" wrote in message
t...
It was a bit of a faff though, so I wondered if anyone has any tips
for making the job easier, or what tools to use, etc.

Well, I use garden cane and twine. I've heard of people using toy guns
firing some sort of projectile attached to some despooled thread. This can
be used to pull through the string and then the cable.

If the ground below is smooth, I've even heard of cheap radio controlled
cars, a mirror and a torch being used in a similar manner. I doubt either
method would handle sleeper walls well.
==============================
Hi Christian,

I don't know if it's an urban myth, but I remember a tale which involved
judicious use of a cat, some string, and a kipper.

Cheers,

Ian

Getting cables under the floorboards
 

On Wed, 3 Sep 2003 20:07:34 +0100, "Ian Smeaton"
wrote:


I don't know if it's an urban myth, but I remember a tale which involved
judicious use of a cat, some string, and a kipper.

We used tinned cat food rathe than a kipper, and the string was very
light thread, partially cut so that it would break if it got snagged
.... but we did exactly this to start the process of running a cable
under the kitchen floor of a London flat :-)

Julian

--
Julian Fowler
julian (at) bellevue-barn (dot) org (dot) uk

Getting cables under the floorboards
 

In article ,
Julian Fowler wrote:
We used tinned cat food rathe than a kipper, and the string was very
light thread, partially cut so that it would break if it got snagged

But then you wouldn't be able to pull the cat out. Suppose they're cheap
enough, though.

--
*Experience is something you don't get until just after you need it.*

Dave Plowman London SW 12
RIP Acorn

Getting cables under the floorboards
 

"Dave Plowman" wrote
| Julian Fowler wrote:
| We used tinned cat food rathe than a kipper, and the string was very
| light thread, partially cut so that it would break if it got snagged
| But then you wouldn't be able to pull the cat out. Suppose they're cheap
| enough, though.

That Is Not A Nice Comment.

The problem with cats though is that they're inquisitive and may not take
the shortest route, so if they decide to have an explore all around under
the floorboards before popping out to claim the kipper you might have to
re-do cable length calculations.

I can't see a suggested derating factor for "Below Floorboards Pulled By
Cat" in the tables for mounting methods in the IEE regs.

Owain

Getting cables under the floorboards
 

"Andy Wade" wrote in message
...
"Andy Dingley" wrote in message
...
On Thu, 4 Sep 2003 12:49:12 +0100, "Owain"

That's the difference between the IEE and the IETF

IETF? - Institution of electrical tractive felines?

Or try EIA/TIA 568 - lots of reference to CAT's in there :-)
--
Andy


Actually a CAT5 cable was one of those I was planning to go under the floor!

Peter.

Getting cables under the floorboards
 

"Andy Wade" wrote
| "Andy Dingley"
| That's the difference between the IEE and the IETF
| IETF? - Institution of electrical tractive felines?

Very good.

| Or try EIA/TIA 568 - lots of reference to CAT's in there :-)

The problem with anything more than CAT1 is getting the cats to pull in the
same direction. It must be bloody pandemonium trying to install a 6 CAT
cable. Particularly if only four of them like kipper.

Owain

Getting cables under the floorboards
 

On Thu, 4 Sep 2003 15:10:53 +0100, "Andy Wade"
wrote:

That's the difference between the IEE and the IETF

IETF? - Institution of electrical tractive felines?

Internet Engineering Task Force

Publishers of RFC 1149
"A Standard for the Transmission of IP Datagrams on Avian Carriers"
ftp://ftp.rfc-editor.org/in-notes/rfc1149.txt

and RFC 2549
"IP over Avian Carriers with QoS"
ftp://ftp.rfc-editor.org/in-notes/rfc2549.txt

Getting cables under the floorboards
 

"Andy Dingley" wrote
| Internet Engineering Task Force
| Publishers of RFC 1149
| "A Standard for the Transmission of IP Datagrams on Avian Carriers"
| ftp://ftp.rfc-editor.org/in-notes/rfc1149.txt
| and RFC 2549
| "IP over Avian Carriers with QoS"
| ftp://ftp.rfc-editor.org/in-notes/rfc2549.txt

RFC 875 - Gateways, architectures, and heffalumps

Available from the above sites.

Owain

Getting cables under the floorboards
 

"Ian Smeaton" wrote in message ...
"Christian McArdle" wrote in message
t...
It was a bit of a faff though, so I wondered if anyone has any tips
for making the job easier, or what tools to use, etc.

Well, I use garden cane and twine. I've heard of people using toy guns
firing some sort of projectile attached to some despooled thread. This can
be used to pull through the string and then the cable.

If the ground below is smooth, I've even heard of cheap radio controlled
cars, a mirror and a torch being used in a similar manner. I doubt either
method would handle sleeper walls well.

I don't know if it's an urban myth, but I remember a tale which involved
judicious use of a cat, some string, and a kipper.

I've done the job using a pet rat (borrowed from a friend while on
holiday) - tied a length of cotton loosely around its middle and it
worked a treat (tied a length of string to the cotton, pulled that
through, then attached the cable to the string.

It was crucial that Ratty was constrained to operate within two
joists, so didn't have the run of the entire house between the
floors...

David

Getting cables under the floorboards
 

David wrote:
"Ian Smeaton" wrote in message
...
"Christian McArdle" wrote in
message t...
It was a bit of a faff though, so I wondered if anyone has any tips
for making the job easier, or what tools to use, etc.

Well, I use garden cane and twine. I've heard of people using toy
guns firing some sort of projectile attached to some despooled
thread. This can be used to pull through the string and then the
cable.

If the ground below is smooth, I've even heard of cheap radio
controlled cars, a mirror and a torch being used in a similar
manner. I doubt either method would handle sleeper walls well.

I don't know if it's an urban myth, but I remember a tale which
involved judicious use of a cat, some string, and a kipper.

I've done the job using a pet rat (borrowed from a friend while on
holiday) - tied a length of cotton loosely around its middle and it
worked a treat (tied a length of string to the cotton, pulled that
through, then attached the cable to the string.

It was crucial that Ratty was constrained to operate within two
joists, so didn't have the run of the entire house between the
floors...

Wasn't there a poster on here recently with a trained ferret earning a few
hundred nicker a week of the wee beastie?

--
James...
http://www.jameshart.co.uk/

Getting cables under the floorboards
 

On Thu, 04 Sep 2003 18:11:25 +0100, Andy Dingley said:


Internet Engineering Task Force

Publishers of RFC 1149 "A Standard for the Transmission of IP
Datagrams on Avian Carriers"
ftp://ftp.rfc-editor.org/in-notes/rfc1149.txt

The first, and only implementation of the standard:
http://www.blug.linux.no/rfc1149/

See also
ftp://ftp.rfc-editor.org/in-notes/rfc1217.txt

or any of the April RFCs listed at
http://home.swipnet.se/cfmd/rfc/dir/fye.html
http://www.bpfh.net/rfc/
http://www.wikipedia.org/wiki/April_1st_RFC

--
Alan J. Wylie http://www.glaramara.freeserve.co.uk/
"Perfection [in design] is achieved not when there is nothing left to add,
but rather when there is nothing left to take away."
-- Antoine de Saint-Exupery

Getting cables under the floorboards
 

In article , Ian Smeaton
writes

"Christian McArdle" wrote in message
et...
It was a bit of a faff though, so I wondered if anyone has any tips
for making the job easier, or what tools to use, etc.

Well, I use garden cane and twine. I've heard of people using toy guns
firing some sort of projectile attached to some despooled thread. This can
be used to pull through the string and then the cable.

If the ground below is smooth, I've even heard of cheap radio controlled
cars, a mirror and a torch being used in a similar manner. I doubt either
method would handle sleeper walls well.
==============================
Hi Christian,

I don't know if it's an urban myth, but I remember a tale which involved
judicious use of a cat, some string, and a kipper.

Cheers,

Ian


How do you get the kipper to run so that the cat will chase it?
--
Peter

Ying tong iddle-i po!

Getting cables under the floorboards
 

On Thu, 4 Sep 2003 22:42:28 +0100, Peter Twydell
wrote:

How do you get the kipper to run so that the cat will chase it?

Let me explain.....

The kipper is dead, and has no ability to run. What you do is pull the
kipper through using a piece of string from the place where you want
your cat to run to. Attach a piece of string to the cat before it sets
off, then you can collect the string from the cat when it comes out
the other side. Job complete.

Hmm, I'm sure there's a problem with my logic somewhere, but I can't
see what it is ;)

PoP

Getting cables under the floorboards
 

Andy Dingley wrote:
On Thu, 4 Sep 2003 15:10:53 +0100, "Andy Wade"
wrote:

That's the difference between the IEE and the IETF

IETF? - Institution of electrical tractive felines?

Internet Engineering Task Force

Publishers of RFC 1149
"A Standard for the Transmission of IP Datagrams on Avian Carriers"
ftp://ftp.rfc-editor.org/in-notes/rfc1149.txt

And proved to work :- 'http://www.blug.linux.no/rfc1149/'

and RFC 2549
"IP over Avian Carriers with QoS"
ftp://ftp.rfc-editor.org/in-notes/rfc2549.txt

AP

--

We were always told that a million monkeys typing for a million years
would eventually produce the works of Shakespeare. Now, thanks to the
Internet, we know this is not true.

Getting cables under the floorboards
 

In article , PoP E-
writes
On Thu, 4 Sep 2003 22:42:28 +0100, Peter Twydell
wrote:

How do you get the kipper to run so that the cat will chase it?

Let me explain.....

The kipper is dead, and has no ability to run. What you do is pull the
kipper through using a piece of string from the place where you want
your cat to run to. Attach a piece of string to the cat before it sets
off, then you can collect the string from the cat when it comes out
the other side. Job complete.

Thanks for the explanation; I would never have guessed. Dead kippers.
eh? There's a novelty.

Hmm, I'm sure there's a problem with my logic somewhere, but I can't
see what it is ;)

PoP


--
Peter

Ying tong iddle-i po!