|
Lincoln 225 welder, what can it do?
Get a book on welding. Any store that sells welding equipment will have
a good book. Libraries, also. I have used my 225 amp welder to make all kinds of stuff for my plant and for use around the shop. Lots of work tables, a table saw base, frames to hold lights for work benches. I have cut steel channel, heated rods for bending with the carbon arc torch ( before I got gas equipment). I have a 50 amp service/breaker for the welder. I think that is the minimum. Paul |
Steel (hot/cold rolled) from about 16 ga to 3/8" in one pass. Aluminum
is out, the unit is not DC. There is a nice variety of hard surfacing rods that run fine. This thing handles angle iron and structural tube beautifully. Ignoramus584 wrote: What kinds of things could I weld with it? i |
On 5 Jan 2005 18:08:29 GMT, Ignoramus584
calmly ranted: What kinds of things could I weld with it? Go to the source: Lincoln Electric https://ssl.lincolnelectric.com/linc...tore.asp?cat=7 Try the arc welding project books, etc. Their foundation books are dirt cheap. -- "Menja bé, caga fort!" |
"Ignoramus584" wrote in message ... What kinds of things could I weld with it? i Is it an AC or AC/DC welder? Steve |
Ignoramus584" wrote in message ... | | What kinds of things could I weld with it? Bet it does great hot dogs! Someone have a recipe! |
On Thu, 06 Jan 2005 02:45:55 GMT, "carl mciver"
wrote: Ignoramus584" wrote in message ... | What kinds of things could I weld with it? Bet it does great hot dogs! Someone have a recipe! You don't need a welder to "Westinghouse" a hot dog - just two stainless steel table forks, a "Killer Cord" with a 120V wall plug and two alligator clips on the other end, and a wooden cutting board. Stick the tines of forks in each end of the hot dog about 1/2", clip the power cord onto the fork handles or shafts, arrange the dog and forks on the cutting board so it's insulated from the counter or anything metallic. Then plug in the power cord till the hot dog reaches the desired state of doneness - and don't touch it while it's cooking. If you have a SWMBO, don't use the good forks. ;-) Or buy the old Presto "Hot Dogger" which did the same thing, but enclosed the dogs in a plastic case to catch spatters and prevent electrical contact. -- Bruce -- -- Bruce L. Bergman, Woodland Hills (Los Angeles) CA - Desktop Electrician for Westend Electric - CA726700 5737 Kanan Rd. #359, Agoura CA 91301 (818) 889-9545 Spamtrapped address: Remove the python and the invalid, and use a net. |
Lincoln 225 is probably the worlds most popular welder and is pretty
well capable of welding up most any thing for the average user........in the line of structural types of steels......and some others materials with the right rods........aluminum, cast, stainless......... |
On Thu, 06 Jan 2005 04:39:18 GMT, Bruce L. Bergman
wrote: On Thu, 06 Jan 2005 02:45:55 GMT, "carl mciver" wrote: Ignoramus584" wrote in message ... | What kinds of things could I weld with it? Bet it does great hot dogs! Someone have a recipe! You don't need a welder to "Westinghouse" a hot dog - just two stainless steel table forks, a "Killer Cord" with a 120V wall plug and two alligator clips on the other end, and a wooden cutting board. Stick the tines of forks in each end of the hot dog about 1/2", clip the power cord onto the fork handles or shafts, arrange the dog and forks on the cutting board so it's insulated from the counter or anything metallic. Then plug in the power cord till the hot dog reaches the desired state of doneness - and don't touch it while it's cooking. If you have a SWMBO, don't use the good forks. ;-) Or buy the old Presto "Hot Dogger" which did the same thing, but enclosed the dogs in a plastic case to catch spatters and prevent electrical contact. -- Bruce -- I had one of the old Hot Doggers. I only used it a couple times as it made the hot dog taste a bit "off" for some reason. Gunner, hot dog coni-sewer G "Gunner, you are the same ridiculous liberal f--k you ever where." Scipio |
On Thu, 06 Jan 2005 14:21:33 GMT, Gunner
wrote: On Thu, 06 Jan 2005 04:39:18 GMT, Bruce L. Bergman wrote: On Thu, 06 Jan 2005 02:45:55 GMT, "carl mciver" wrote: Ignoramus584" wrote in message ... | What kinds of things could I weld with it? Bet it does great hot dogs! Someone have a recipe! You don't need a welder to "Westinghouse" a hot dog - just two stainless steel table forks, a "Killer Cord" with a 120V wall plug and two alligator clips on the other end, and a wooden cutting board. Stick the tines of forks in each end of the hot dog about 1/2", clip the power cord onto the fork handles or shafts, arrange the dog and forks on the cutting board so it's insulated from the counter or anything metallic. Then plug in the power cord till the hot dog reaches the desired state of doneness - and don't touch it while it's cooking. If you have a SWMBO, don't use the good forks. ;-) Or buy the old Presto "Hot Dogger" which did the same thing, but enclosed the dogs in a plastic case to catch spatters and prevent electrical contact. I had one of the old Hot Doggers. I only used it a couple times as it made the hot dog taste a bit "off" for some reason. Dummies at Presto used pot-metal Zinc/Tin/AL/Mystery Metal 'hot-dog stabber' electrodes to be cheap, and they added unwanted flavor to the dog. (Duh!) That's the reason I said to use Stainless Steel forks. -- Bruce -- -- Bruce L. Bergman, Woodland Hills (Los Angeles) CA - Desktop Electrician for Westend Electric - CA726700 5737 Kanan Rd. #359, Agoura CA 91301 (818) 889-9545 Spamtrapped address: Remove the python and the invalid, and use a net. |
On Thu, 06 Jan 2005 16:46:29 GMT, Bruce L. Bergman
wrote: Or buy the old Presto "Hot Dogger" which did the same thing, but enclosed the dogs in a plastic case to catch spatters and prevent electrical contact. I had one of the old Hot Doggers. I only used it a couple times as it made the hot dog taste a bit "off" for some reason. Dummies at Presto used pot-metal Zinc/Tin/AL/Mystery Metal 'hot-dog stabber' electrodes to be cheap, and they added unwanted flavor to the dog. (Duh!) That's the reason I said to use Stainless Steel forks. -- Bruce -- That could have been it. They always reminded me of how your mouth tastes after the dentist drilled. After I got my first nuke (microwave), I was in hog heaven for wienie cooking. Gunner "Gunner, you are the same ridiculous liberal f--k you ever where." Scipio |
On 5 Jan 2005 18:08:29 GMT, Ignoramus584
vaguely proposed a theory .......and in reply I say!: remove ns from my header address to reply via email metals mainly.....G What kinds of things could I weld with it? i |
| All times are GMT +1. The time now is 05:51 AM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter