Minimize burrs drilling Aluminum
 

I have a production opportunity that involves drilling 1/2" and 3/8"
through holes in 2"x 2" x1/8" square Aluminum tube. I don't know the
alloy yet. The holes don't have to be burr-free but I would like to
minimize the burrs without any secondary operations. The holes will be
drilled with a drill press. So, I think it comes down to what type of
drill bit configuration to use. Would brad-points or Forstner bits
work? I looked on the web and saw all kinds of slick burr removal tools
but no good answers for single operation drilling.

I bet Joe knows!

Minimize burrs drilling Aluminum
 

Tom Gardner Mars@Tacks fired this volley in news:r-
:

The holes don't have to be burr-free but I would like to
minimize the burrs without any secondary operations.

Tom, you can't eliminate the "breakout" burrs. Use the fastest feed you
can to get a clean chip, and you will almost completely eliminate the
burrs at the top of the hole.

Son, de-burring is part of the process. Unless you put a 'waste sheet'
under the material, and drill into it past the shoulder of the bit,
you're going to get burrs. And then only if it's clamped so tight to the
work that there's not a chance of pushing a burr between the sheets.

LLoyd

Minimize burrs drilling Aluminum
 

On 6/22/2014 2:18 PM, Lloyd E. Sponenburgh wrote:
Tom Gardner Mars@Tacks fired this volley in news:r-
:

The holes don't have to be burr-free but I would like to
minimize the burrs without any secondary operations.

Tom, you can't eliminate the "breakout" burrs. Use the fastest feed you
can to get a clean chip, and you will almost completely eliminate the
burrs at the top of the hole.

Son, de-burring is part of the process. Unless you put a 'waste sheet'
under the material, and drill into it past the shoulder of the bit,
you're going to get burrs. And then only if it's clamped so tight to the
work that there's not a chance of pushing a burr between the sheets.

LLoyd



A sacrificial piece of hardwood be sufficient? How about a drill
bushing under the tube?

Minimize burrs drilling Aluminum
 

On Sun, 22 Jun 2014 14:26:42 -0400, Tom Gardner Mars@Tacks wrote:

On 6/22/2014 2:18 PM, Lloyd E. Sponenburgh wrote:
Tom Gardner Mars@Tacks fired this volley in news:r-
:

The holes don't have to be burr-free but I would like to
minimize the burrs without any secondary operations.

Tom, you can't eliminate the "breakout" burrs. Use the fastest feed you
can to get a clean chip, and you will almost completely eliminate the
burrs at the top of the hole.

Son, de-burring is part of the process. Unless you put a 'waste sheet'
under the material, and drill into it past the shoulder of the bit,
you're going to get burrs. And then only if it's clamped so tight to the
work that there's not a chance of pushing a burr between the sheets.

LLoyd



A sacrificial piece of hardwood be sufficient? How about a drill
bushing under the tube?

Bushing still wont help. That last burr is the result the metal being
torn away from the mass by the downward pressure.

The only way you are going to be burr free is to use a deburring tool.
Which is really not a big deal in Aluminum.

http://www.vargus.com/Shaviv/

http://www.noga.com/

http://www.mscdirect.com/browse/tn/A...navid=12100123

etc etc

I have Vargus, and Noga of variouis kinds, from hole to sheet
deburring....and they all work great once you get the hang of em.


Gunner

"Libertarianism IS fascism... Fascism is corporate government – a Libertarian’s wet dream"
Tala Brandeis
Owner at Tala Brandeis Associates"

Minimize burrs drilling Aluminum
 

On Sun, 22 Jun 2014 14:26:42 -0400, Tom Gardner Mars@Tacks wrote:

On 6/22/2014 2:18 PM, Lloyd E. Sponenburgh wrote:
Tom Gardner Mars@Tacks fired this volley in news:r-
:

The holes don't have to be burr-free but I would like to
minimize the burrs without any secondary operations.

Tom, you can't eliminate the "breakout" burrs. Use the fastest feed you
can to get a clean chip, and you will almost completely eliminate the
burrs at the top of the hole.

Son, de-burring is part of the process. Unless you put a 'waste sheet'
under the material, and drill into it past the shoulder of the bit,
you're going to get burrs. And then only if it's clamped so tight to the
work that there's not a chance of pushing a burr between the sheets.

LLoyd



A sacrificial piece of hardwood be sufficient? How about a drill
bushing under the tube?

Either will only minimize burrs. They're an annoying fact of life.

--
There is nothing more frightening than ignorance in action.

--Johann Wolfgang von Goethe

Minimize burrs drilling Aluminum
 

On Sunday, June 22, 2014 1:18:06 PM UTC-7, Larry Jaques wrote:
On Sun, 22 Jun 2014 14:26:42 -0400, Tom Gardner Mars@Tacks wrote:



On 6/22/2014 2:18 PM, Lloyd E. Sponenburgh wrote:

Tom Gardner Mars@Tacks fired this volley in news:r-

:



The holes don't have to be burr-free but I would like to

minimize the burrs without any secondary operations.



Tom, you can't eliminate the "breakout" burrs. Use the fastest feed you

can to get a clean chip, and you will almost completely eliminate the

burrs at the top of the hole.



Son, de-burring is part of the process. Unless you put a 'waste sheet'

under the material, and drill into it past the shoulder of the bit,

you're going to get burrs. And then only if it's clamped so tight to the

work that there's not a chance of pushing a burr between the sheets.



LLoyd







A sacrificial piece of hardwood be sufficient? How about a drill

bushing under the tube?



Either will only minimize burrs. They're an annoying fact of life.



--

There is nothing more frightening than ignorance in action.



--Johann Wolfgang von Goethe


It's a FACT of life that Mark Wieber clique of idiot members have no clues. Never have. Never will:

http://www.cogsdill.com/products/deburring/

Minimize burrs drilling Aluminum
 

On 6/22/2014 4:10 PM, Gunner Asch wrote:
On Sun, 22 Jun 2014 14:26:42 -0400, Tom Gardner Mars@Tacks wrote:

On 6/22/2014 2:18 PM, Lloyd E. Sponenburgh wrote:
Tom Gardner Mars@Tacks fired this volley in news:r-
:

The holes don't have to be burr-free but I would like to
minimize the burrs without any secondary operations.

Tom, you can't eliminate the "breakout" burrs. Use the fastest feed you
can to get a clean chip, and you will almost completely eliminate the
burrs at the top of the hole.

Son, de-burring is part of the process. Unless you put a 'waste sheet'
under the material, and drill into it past the shoulder of the bit,
you're going to get burrs. And then only if it's clamped so tight to the
work that there's not a chance of pushing a burr between the sheets.

LLoyd



A sacrificial piece of hardwood be sufficient? How about a drill
bushing under the tube?

Bushing still wont help. That last burr is the result the metal being
torn away from the mass by the downward pressure.

The only way you are going to be burr free is to use a deburring tool.
Which is really not a big deal in Aluminum.

http://www.vargus.com/Shaviv/

http://www.noga.com/

http://www.mscdirect.com/browse/tn/A...navid=12100123

etc etc

I have Vargus, and Noga of variouis kinds, from hole to sheet
deburring....and they all work great once you get the hang of em.


Gunner

"Libertarianism IS fascism... Fascism is corporate government – a Libertarian’s wet dream"
Tala Brandeis
Owner at Tala Brandeis Associates"



No time for another operation and a smal burr is OK, I just want it minimum.

Minimize burrs drilling Aluminum
 

On 6/22/2014 4:18 PM, Larry Jaques wrote:

Either will only minimize burrs. They're an annoying fact of life.

--

Well, that is the title of the thread.

Minimize burrs drilling Aluminum
 

On Mon, 23 Jun 2014 01:36:33 -0400, Tom Gardner Mars@Tacks wrote:

On 6/22/2014 4:10 PM, Gunner Asch wrote:
On Sun, 22 Jun 2014 14:26:42 -0400, Tom Gardner Mars@Tacks wrote:

On 6/22/2014 2:18 PM, Lloyd E. Sponenburgh wrote:
Tom Gardner Mars@Tacks fired this volley in news:r-
:

The holes don't have to be burr-free but I would like to
minimize the burrs without any secondary operations.

Tom, you can't eliminate the "breakout" burrs. Use the fastest feed you
can to get a clean chip, and you will almost completely eliminate the
burrs at the top of the hole.

Son, de-burring is part of the process. Unless you put a 'waste sheet'
under the material, and drill into it past the shoulder of the bit,
you're going to get burrs. And then only if it's clamped so tight to the
work that there's not a chance of pushing a burr between the sheets.

LLoyd



A sacrificial piece of hardwood be sufficient? How about a drill
bushing under the tube?

Bushing still wont help. That last burr is the result the metal being
torn away from the mass by the downward pressure.

The only way you are going to be burr free is to use a deburring tool.
Which is really not a big deal in Aluminum.

http://www.vargus.com/Shaviv/

http://www.noga.com/

http://www.mscdirect.com/browse/tn/A...navid=12100123

etc etc

I have Vargus, and Noga of variouis kinds, from hole to sheet
deburring....and they all work great once you get the hang of em.


Gunner

"Libertarianism IS fascism... Fascism is corporate government – a Libertarian’s wet dream"
Tala Brandeis
Owner at Tala Brandeis Associates"



No time for another operation and a smal burr is OK, I just want it minimum.

It takes a second or so per hole to run a deburring tool around the
inside of each hole. If you dont have that time...use a 2 flute end
mill to drill your holes.


"Libertarianism IS fascism... Fascism is corporate government – a Libertarian’s wet dream"
Tala Brandeis
Owner at Tala Brandeis Associates"

Minimize burrs drilling Aluminum
 

On Mon, 23 Jun 2014 01:37:50 -0400, Tom Gardner Mars@Tacks wrote:

On 6/22/2014 4:18 PM, Larry Jaques wrote:

Either will only minimize burrs. They're an annoying fact of life.

--

Well, that is the title of the thread.

Yes, but I read between the lines. You want total freedom from burrs,
and that's a fact.

--
Learning to ignore things is one of the great paths to inner peace.
-- Robert J. Sawyer

Minimize burrs drilling Aluminum
 

On Sunday, June 22, 2014 10:36:33 PM UTC-7, Tom Gardner wrote:
On 6/22/2014 4:10 PM, Gunner Asch wrote:

On Sun, 22 Jun 2014 14:26:42 -0400, Tom Gardner Mars@Tacks wrote:



On 6/22/2014 2:18 PM, Lloyd E. Sponenburgh wrote:

Tom Gardner Mars@Tacks fired this volley in news:r-

:



The holes don't have to be burr-free but I would like to

minimize the burrs without any secondary operations.



Tom, you can't eliminate the "breakout" burrs. Use the fastest feed you

can to get a clean chip, and you will almost completely eliminate the

burrs at the top of the hole.



Son, de-burring is part of the process. Unless you put a 'waste sheet'

under the material, and drill into it past the shoulder of the bit,

you're going to get burrs. And then only if it's clamped so tight to the

work that there's not a chance of pushing a burr between the sheets.



LLoyd







A sacrificial piece of hardwood be sufficient? How about a drill

bushing under the tube?



Bushing still wont help. That last burr is the result the metal being

torn away from the mass by the downward pressure.



The only way you are going to be burr free is to use a deburring tool.

Which is really not a big deal in Aluminum.



http://www.vargus.com/Shaviv/



http://www.noga.com/



http://www.mscdirect.com/browse/tn/A...navid=12100123



etc etc



I have Vargus, and Noga of variouis kinds, from hole to sheet

deburring....and they all work great once you get the hang of em.





Gunner



"Libertarianism IS fascism... Fascism is corporate government � a Libertarian�s wet dream"

Tala Brandeis

Owner at Tala Brandeis Associates"







No time for another operation and a smal burr is OK, I just want it minimum.


No time to do the job right/do a quality job.

Typical Mark Wieber clique of idiot mentality.

Minimize burrs drilling Aluminum
 

"Lloyd E. Sponenburgh" lloydspinsidemindspring.com wrote:

Tom Gardner Mars@Tacks fired this volley in news:r-
:

The holes don't have to be burr-free but I would like to
minimize the burrs without any secondary operations.

Tom, you can't eliminate the "breakout" burrs. Use the fastest feed you
can to get a clean chip, and you will almost completely eliminate the
burrs at the top of the hole.
If the work is clamped securely, you can use an end mill to drill
through. It leaves a lot less burr than a regular drill bit.

Jon

Minimize burrs drilling Aluminum
 

Jon Elson fired this volley in news:r-
:

If the work is clamped securely, you can use an end mill to drill
through. It leaves a lot less burr than a regular drill bit.

To ensure proper chip clearing (even with center-cutting mills), you should
first drill a pilot hole about 30% of the finished diameter.

LLoyd

Minimize burrs drilling Aluminum
 

On Monday, June 23, 2014 1:28:28 PM UTC-7, Lloyd E. Sponenburgh wrote:
Jon Elson fired this volley in news:r-

:



If the work is clamped securely, you can use an end mill to drill

through. It leaves a lot less burr than a regular drill bit.



To ensure proper chip clearing (even with center-cutting mills), you should

first drill a pilot hole about 30% of the finished diameter.



LLoyd


Loud has no idea what good, modern, CADCAM programs offer and why they often make drilling pilot holes an unneeded and unnecessary operation.

Minimize burrs drilling Aluminum
 

"Lloyd E. Sponenburgh" lloydspinsidemindspring.com fired this volley
in . 3.70:

To ensure proper chip clearing (even with center-cutting mills), you
should first drill a pilot hole about 30% of the finished diameter.

I should have said, Tom, that I'm presuming you do not have CNC, and would
be using and endmill as a plain drill.

If you had cnc, you could just spiral drill with an endmill and get good
results.

Lloyd

Minimize burrs drilling Aluminum
 

Larry Jaques wrote:
On Sun, 22 Jun 2014 14:26:42 -0400, Tom Gardner Mars@Tacks wrote:

On 6/22/2014 2:18 PM, Lloyd E. Sponenburgh wrote:
Tom Gardner Mars@Tacks fired this volley in news:r-
:

The holes don't have to be burr-free but I would like to
minimize the burrs without any secondary operations.

Tom, you can't eliminate the "breakout" burrs. Use the fastest feed you
can to get a clean chip, and you will almost completely eliminate the
burrs at the top of the hole.

Son, de-burring is part of the process. Unless you put a 'waste sheet'
under the material, and drill into it past the shoulder of the bit,
you're going to get burrs. And then only if it's clamped so tight to the
work that there's not a chance of pushing a burr between the sheets.

LLoyd



A sacrificial piece of hardwood be sufficient? How about a drill
bushing under the tube?

Either will only minimize burrs. They're an annoying fact of life.

how about punching holes in the tube and skip the drill?

Minimize burrs drilling Aluminum
 

On 6/23/2014 9:29 AM, Larry Jaques wrote:
On Mon, 23 Jun 2014 01:37:50 -0400, Tom Gardner Mars@Tacks wrote:

On 6/22/2014 4:18 PM, Larry Jaques wrote:

Either will only minimize burrs. They're an annoying fact of life.

--

Well, that is the title of the thread.

Yes, but I read between the lines. You want total freedom from burrs,
and that's a fact.

--
Learning to ignore things is one of the great paths to inner peace.
-- Robert J. Sawyer



Yep!