Stuck setscrew update..
 

A couple of days ago a guy from the local sawmill
stopped in for advice on how to remove a stuck
setscrew in a log de-barker head. It was about
3/4 below flush, 3/8 thread. I gave him a 3/16
drill welded to an extension and told him to turn
it
as slow as possible with heavy pressure. The hex
was stripped out bad. The bits he had would not
touch it. He came by today and said he got it out
and didn't break the drill but he used a hammer
drill to turn it! The drill went through the screw
with
no arguing at all! He was a happy camper.. ;)}
Thought you guys would like to hear this.... I
never
thought of using a hammer drill for this....
phil k.

Stuck setscrew update..
 

"Phil Kangas" wrote in message
...
A couple of days ago a guy from the local sawmill
stopped in for advice on how to remove a stuck
setscrew in a log de-barker head. It was about
3/4 below flush, 3/8 thread. I gave him a 3/16
drill welded to an extension and told him to turn it
as slow as possible with heavy pressure. The hex
was stripped out bad. The bits he had would not
touch it. He came by today and said he got it out
and didn't break the drill but he used a hammer
drill to turn it! The drill went through the screw with
no arguing at all! He was a happy camper.. ;)}
Thought you guys would like to hear this.... I never
thought of using a hammer drill for this....
phil k.

Did you use a left hand twist bit? I would have guessed that you might use
an impact driver, drill a pilot hole, then weld an ez out to the socket on
the impact driver, and maybe that would do it.

Anyway, was it it the percussion that did the trick?

Steve

Stuck setscrew update..
 

"Steve B" wrote in
message
...

"Phil Kangas" wrote in
message ...
A couple of days ago a guy from the local
sawmill
stopped in for advice on how to remove a stuck
setscrew in a log de-barker head. It was about
3/4 below flush, 3/8 thread. I gave him a 3/16
drill welded to an extension and told him to
turn it
as slow as possible with heavy pressure. The
hex
was stripped out bad. The bits he had would not
touch it. He came by today and said he got it
out
and didn't break the drill but he used a hammer
drill to turn it! The drill went through the
screw with
no arguing at all! He was a happy camper.. ;)}
Thought you guys would like to hear this.... I
never
thought of using a hammer drill for this....
phil k.

Did you use a left hand twist bit? I would have
guessed that you might use an impact driver,
drill a pilot hole, then weld an ez out to the
socket on the impact driver, and maybe that
would do it.

Anyway, was it it the percussion that did the
trick?

Steve

The drill bit was right hand twist, a good one but
a bit on the short
side of normal as the web was thicker and the
point was split.
Apparently the percussion effect was the trick!
Had I seen the
guy pick up the hammer drill I would have been
shocked! So
it's true, you learn something new every day, eih?
phil k.

Stuck setscrew update..
 

I've been able to remove rusted bolts or nuts with impact
wrench. I'd not have thought of using a hammer drill for a
stuck setscrew. Great idea, thank you. Oh, uh, er, thank
your friend who had the idea.

You learn something new every day, if you're paying
attention and humble enough to be teachable.
--
Christopher A. Young
Learn more about Jesus
www.lds.org
..


"Phil Kangas" wrote in message
...

The drill bit was right hand twist, a good one
but a bit on the short side of normal as the
web was thicker and the point was split.

Apparently the percussion effect was the trick!
Had I seen the guy pick up the hammer drill I
would have been shocked! So it's true, you
learn something new every day, eih?

phil k.