17 spline shaft
 

I'm restoring a 1964 garden tractor. The shaft for the cone clutch is
17 spline. In all my searching, I only find 16 and 20. The OD measured
0.7550.

Is there a 17 that is standard? Sources? What I actually need is the
interior spline bushing (with or without flange) that slides on the
shaft.

Andy

17 spline shaft
 

wrote in message
...
I'm restoring a 1964 garden tractor. The shaft for the cone clutch is
17 spline. In all my searching, I only find 16 and 20. The OD measured
0.7550.

Is there a 17 that is standard? Sources? What I actually need is the
interior spline bushing (with or without flange) that slides on the
shaft.

Andy

Do you have a copy of the Machiery Handbook? It may be in there...
--


Regards,
Joe Agro, Jr.
(800) 871-5022 x113
01.908.542.0244
Flagship Site: http://www.Drill-HQ.com
Automatic / Pneumatic Drills: http://www.AutoDrill.com
Multiple Spindle Drills: http://www.Multi-Drill.com
Production Tapping: http://Production-Tapping-Equipment.com/
VIDEOS: http://www.youtube.com/user/AutoDrill
FACEBOOK: http://www.facebook.com/AutoDrill
TWITTER: http://twitter.com/AutoDrill


V8013-R

17 spline shaft
 

On Thu, 11 Aug 2011 08:11:05 -0400, "Joe AutoDrill"
wrote:

wrote in message
.. .
I'm restoring a 1964 garden tractor. The shaft for the cone clutch is
17 spline. In all my searching, I only find 16 and 20. The OD measured
0.7550.

Is there a 17 that is standard? Sources? What I actually need is the
interior spline bushing (with or without flange) that slides on the
shaft.

Andy

Do you have a copy of the Machiery Handbook? It may be in there...


That is one of the places I found 16 and 20 in that OD.

17 spline shaft
 

On Aug 11, 10:38*pm, wrote:
On Thu, 11 Aug 2011 08:11:05 -0400, "Joe AutoDrill"

wrote:
wrote in message
.. .
I'm restoring a 1964 garden tractor. The shaft for the cone clutch is
17 spline. In all my searching, I only find 16 and 20. The OD measured
0.7550.

Is there a 17 that is standard? Sources? What I actually need is the
interior spline bushing (with or without flange) that slides on the
shaft.

Andy

Do you have a copy of the Machiery Handbook? *It may be in there...

That is one of the places I found 16 and 20 in that OD.

Very likely that it could be a special. We do them all the time.

17 spline shaft
 

Various pumps generators and other power equipment utilize splined drive
shafts, so some suitable parts may be found at some surplus dealers,
including aircraft surplus dealers.

--
WB
..........


wrote in message
...
I'm restoring a 1964 garden tractor. The shaft for the cone clutch is
17 spline. In all my searching, I only find 16 and 20. The OD measured
0.7550.

Is there a 17 that is standard? Sources? What I actually need is the
interior spline bushing (with or without flange) that slides on the
shaft.

Andy

17 spline shaft
 

On Fri, 12 Aug 2011 12:38:02 -0400, "Wild_Bill"
wrote:

Various pumps generators and other power equipment utilize splined drive
shafts, so some suitable parts may be found at some surplus dealers,
including aircraft surplus dealers.

Good thinking. I have a jet fuel control. I'll look at it.

17 spline shaft
 

On Thu, 11 Aug 2011 22:38:43 -0500, wrote:

On Thu, 11 Aug 2011 08:11:05 -0400, "Joe AutoDrill"
wrote:

wrote in message
. ..
I'm restoring a 1964 garden tractor. The shaft for the cone clutch is
17 spline. In all my searching, I only find 16 and 20. The OD measured
0.7550.

Is there a 17 that is standard? Sources? What I actually need is the
interior spline bushing (with or without flange) that slides on the
shaft.

Andy

Do you have a copy of the Machiery Handbook? It may be in there...


That is one of the places I found 16 and 20 in that OD.
It's probably a special. I'm working now on a gear that I will need to
make a cutter for because it's a special. This gear is for some type
of winch for a fishing boat. You could make a cutter and broach the
teeth one at a time yourself. Ivan Law put out a book called Gears and
Gear cutting that is a great book and aimed at HSM types. Costs about
20 bucks.
Eric