Trailer sides, solid or expanded?
 

I have a 12 foot dual axle trailer with angle sides. Been thinking of
building a ramp and enclosing the sides. WOuld solid 1/8 inch or 3/4
inch expanded be better? The floor is wood.

Trailer sides, solid or expanded?
 

"stryped" wrote in message
...
I have a 12 foot dual axle trailer with angle sides. Been thinking of
building a ramp and enclosing the sides. WOuld solid 1/8 inch or 3/4
inch expanded be better? The floor is wood.

Check out the weight of your 1/8" steel side panels. 1/2" plywood would be
my choice.

http://www.chapelsteel.com/weight-steel-plate.html
Steve

Trailer sides, solid or expanded?
 

On Jun 9, 10:59*am, "Up North" wrote:
"stryped" wrote in message

...

I have a 12 foot dual axle trailer with angle sides. Been thinking of
building a ramp and enclosing the sides. WOuld solid 1/8 inch or 3/4
inch expanded be better? The floor is wood.

Check out the weight of your 1/8" steel side panels. 1/2" plywood would be
my choice.

http://www.chapelsteel.com/weight-steel-plate.html
Steve

Would painted osb work? How would I attach wood to the angle iron
sides?

Trailer sides, solid or expanded?
 

On Wed, 9 Jun 2010 09:10:21 -0700 (PDT), stryped
wrote:

On Jun 9, 10:59*am, "Up North" wrote:
"stryped" wrote in message

...

I have a 12 foot dual axle trailer with angle sides. Been thinking of
building a ramp and enclosing the sides. WOuld solid 1/8 inch or 3/4
inch expanded be better? The floor is wood.

Check out the weight of your 1/8" steel side panels. 1/2" plywood would be
my choice.

http://www.chapelsteel.com/weight-steel-plate.html
Steve

Would painted osb work? How would I attach wood to the angle iron
sides?

Carraige bolts and maybe holes in the angle iron?

And it might help if you put nuts and lock washers under the nuts.

Gunner

One could not be a successful Leftwinger without realizing that,
in contrast to the popular conception supported by newspapers
and mothers of Leftwingers, a goodly number of Leftwingers are
not only narrow-minded and dull, but also just stupid.
Gunner Asch

Trailer sides, solid or expanded?
 

On Jun 9, 10:10*am, stryped wrote:
On Jun 9, 10:59*am, "Up North" wrote:

"stryped" wrote in message

....

I have a 12 foot dual axle trailer with angle sides. Been thinking of
building a ramp and enclosing the sides. WOuld solid 1/8 inch or 3/4
inch expanded be better? The floor is wood.

Check out the weight of your 1/8" steel side panels. 1/2" plywood would be
my choice.

http://www.chapelsteel.com/weight-steel-plate.html
Steve

Would painted osb work? How would I attach wood to the angle iron
sides?

Um, bolts, maybe, same as anyone else? If you need flat inside, they
sell elevator bolts, like a carriage bolt only with a flat head. You
aren't building a battleship, you want a trailer to be light so you
don't burn up a tank just hauling it over to where you're going to
pick up stuff.

Stan

Trailer sides, solid or expanded?
 

stryped wrote:
On Jun 9, 10:59 am, "Up North" wrote:
"stryped" wrote in message

...

I have a 12 foot dual axle trailer with angle sides. Been thinking
of building a ramp and enclosing the sides. WOuld solid 1/8 inch or
3/4 inch expanded be better? The floor is wood.

Check out the weight of your 1/8" steel side panels. 1/2" plywood
would be my choice.

http://www.chapelsteel.com/weight-steel-plate.html
Steve

Would painted osb work? How would I attach wood to the angle iron
sides?

OSB works well as a sheathing layer underneath tyvek and siding, but for
your application it will barely be a step above particle board. As you want
a higher degree of strength and resistance to falling apart, you should go
with plywood.

Jon

Trailer sides, solid or expanded?
 

Jon Danniken wrote:

stryped wrote:
On Jun 9, 10:59 am, "Up North" wrote:
"stryped" wrote in message

...

I have a 12 foot dual axle trailer with angle sides. Been thinking
of building a ramp and enclosing the sides. WOuld solid 1/8 inch or
3/4 inch expanded be better? The floor is wood.

Check out the weight of your 1/8" steel side panels. 1/2" plywood
would be my choice.

http://www.chapelsteel.com/weight-steel-plate.html
Steve

Would painted osb work? How would I attach wood to the angle iron
sides?

OSB works well as a sheathing layer underneath tyvek and siding, but for
your application it will barely be a step above particle board. As you want
a higher degree of strength and resistance to falling apart, you should go
with plywood.

Jon

Consider FRP paneling - thin, light, waterproof, easy to clean, etc.

Trailer sides, solid or expanded?
 

On Jun 9, 11:41*am, wrote:
On Jun 9, 10:10*am, stryped wrote:





On Jun 9, 10:59*am, "Up North" wrote:

"stryped" wrote in message

....

I have a 12 foot dual axle trailer with angle sides. Been thinking of
building a ramp and enclosing the sides. WOuld solid 1/8 inch or 3/4
inch expanded be better? The floor is wood.

Check out the weight of your 1/8" steel side panels. 1/2" plywood would be
my choice.

http://www.chapelsteel.com/weight-steel-plate.html
Steve

Would painted osb work? How would I attach wood to the angle iron
sides?

Um, bolts, maybe, same as anyone else? *If you need flat inside, they
sell elevator bolts, like a carriage bolt only with a flat head. *You
aren't building a battleship, you want a trailer to be light so you
don't burn up a tank just hauling it over to where you're going to
pick up stuff.

Stan- Hide quoted text -

- Show quoted text -

Problem is my angle is not flat or on edge if that makes sense. The
corner sticks out.

Trailer sides, solid or expanded?
 

"Pete C." wrote in message
ster.com...

Jon Danniken wrote:

stryped wrote:
On Jun 9, 10:59 am, "Up North" wrote:
"stryped" wrote in message

...

I have a 12 foot dual axle trailer with angle sides. Been thinking
of building a ramp and enclosing the sides. WOuld solid 1/8 inch or
3/4 inch expanded be better? The floor is wood.

Check out the weight of your 1/8" steel side panels. 1/2" plywood
would be my choice.

http://www.chapelsteel.com/weight-steel-plate.html
Steve

Would painted osb work? How would I attach wood to the angle iron
sides?

OSB works well as a sheathing layer underneath tyvek and siding, but for
your application it will barely be a step above particle board. As you
want
a higher degree of strength and resistance to falling apart, you should
go
with plywood.

Jon

Consider FRP paneling - thin, light, waterproof, easy to clean, etc

I found three sheets of corrugated plastic in the ditch the other day when I
was on my way to the scrapyard with a load of steel. I have been using one
of them to slide under my truck when I was doing some work on the rear
suspension. I used a couple to throw on top of a load of iron to protect my
ratchet straps from being cut. With an angle iron frame, they also would
work great for trailer sides.
http://www.coroplast.com/Plasticor-whitecap.htm
Steve