Need your help to identify this lathe indexable tool holder andinsert.
 

I order this 16mm indexable tool holder set at but haven't received it
yet.

http://www.tools4cheap.net/proddetai...prod=carb7pclg

I need your help to translate the last numbers to this indexable tool
holder and insert.

Holder SSRCR1616H09
Insert SCMT09T308

I use the nice chart that shows the nomenclature for both holders and
inserts. I know what SSRCR AND SCMT stand for.
I just can't translate the holder 1616H09 and insert 09T308.

What does 1616H09 mean. I know that the holder is 16mm

These numbers do not correlate with anything on the chart I'm using at
http://www.use-enco.com/CGI/INPDFF?PMPAGE=159&PMCTLG=00
and
http://www.use-enco.com/CGI/INPDFF?PMPAGE=171&PMCTLG=00

I want to replace the known insert SCMT09T308 with a different insert
from Enco or Ebay.

Any help would be appreciated.

Rod
San Francisco

Need your help to identify this lathe indexable tool holder andinsert.
 

rodjava wrote:
I order this 16mm indexable tool holder set at but haven't received it
yet.

http://www.tools4cheap.net/proddetai...prod=carb7pclg

I need your help to translate the last numbers to this indexable tool
holder and insert.

Holder SSRCR1616H09
Insert SCMT09T308

It appears from the pic that there are 3 diamond inserts and two square
ones. Also, the diamond at the far right is a different size than the
other two. I can't tell much about the far left holder, although I'm
guessing it has a triangular insert with no center hole. The next one
to it looks like it has a sawed-off brazed bit, maybe. So, it appears
to have 5 different inserts in the set.

Jon

Need your help to identify this lathe indexable tool holder andinsert.
 

On Dec 31, 3:52*pm, Jon Elson wrote:
rodjava wrote:
I order this 16mm indexable tool holder set at but haven't received it
yet.

http://www.tools4cheap.net/proddetai...prod=carb7pclg

I need your help to translate the last numbers to this indexable tool
holder and insert.

Holder SSRCR1616H09
Insert SCMT09T308

It appears from the pic that there are 3 diamond inserts and two square
ones. *Also, the diamond at the far right is a different size than the
other two. *I can't tell much about the far left holder, although I'm
guessing it has a triangular insert with no center hole. *The next one
to it looks like it has a sawed-off brazed bit, maybe. *So, it appears
to have 5 different inserts in the set.

Jon

Jon,
Thanks.
I think the last number are different from the ANSI chart because they
might be metric. This is just a guess. I was hoping to know what
size insert it was as well
as the thickness and radius.

Rod

Need your help to identify this lathe indexable tool holder and insert.
 

On Wed, 31 Dec 2008 16:38:29 -0800 (PST), rodjava
wrote:

On Dec 31, 3:52*pm, Jon Elson wrote:
rodjava wrote:
I order this 16mm indexable tool holder set at but haven't received it
yet.

http://www.tools4cheap.net/proddetai...prod=carb7pclg

I need your help to translate the last numbers to this indexable tool
holder and insert.

Holder SSRCR1616H09
Insert SCMT09T308

It appears from the pic that there are 3 diamond inserts and two square
ones. *Also, the diamond at the far right is a different size than the
other two. *I can't tell much about the far left holder, although I'm
guessing it has a triangular insert with no center hole. *The next one
to it looks like it has a sawed-off brazed bit, maybe. *So, it appears
to have 5 different inserts in the set.

Jon

Jon,
Thanks.
I think the last number are different from the ANSI chart because they
might be metric. This is just a guess. I was hoping to know what
size insert it was as well
as the thickness and radius.

Rod


SCMT09T308

S=Square insert
C=7 degree relief
M=5 thou tolerance on thickness; 2 thou tolerance on inscribed circle
T=Partly cylindrical hole,Single sided chip breaker/insert
09=3/8" inscribed circle/9mm cutting edge length
T3=5/32" thick
08=1/32" corner radius.

Taken from the J&L catalogue

HTH
Mark Rand
RTFM

Need your help to identify this lathe indexable tool holder andinsert.
 

On Dec 31, 5:42*pm, Mark Rand wrote:
On Wed, 31 Dec 2008 16:38:29 -0800 (PST), rodjava
wrote:



On Dec 31, 3:52*pm, Jon Elson wrote:
rodjava wrote:
I order this 16mm indexable tool holder set at but haven't received it
yet.

http://www.tools4cheap.net/proddetai...prod=carb7pclg

I need your help to translate the last numbers to this indexable tool
holder and insert.

Holder SSRCR1616H09
Insert SCMT09T308

It appears from the pic that there are 3 diamond inserts and two square
ones. *Also, the diamond at the far right is a different size than the
other two. *I can't tell much about the far left holder, although I'm
guessing it has a triangular insert with no center hole. *The next one
to it looks like it has a sawed-off brazed bit, maybe. *So, it appears
to have 5 different inserts in the set.

Jon

Jon,
Thanks.
I think the last number are different from the ANSI chart because they
might *be metric. *This is just a guess. *I was hoping to know what
size insert it was as well
as the thickness and radius.

Rod

SCMT09T308

S=Square insert
C=7 degree relief
M=5 thou tolerance on thickness; 2 thou tolerance on inscribed circle
T=Partly cylindrical hole,Single sided chip breaker/insert
09=3/8" inscribed circle/9mm cutting edge length
T3=5/32" thick
08=1/32" corner radius.

Taken from the J&L catalogue

HTH
Mark Rand
RTFM

Mark,
I can't thank you enough for pointing me in the right direction.
I went to J&L and printed the insert id system.pdf chart which is
exactaly what I was looking for.

Thank you very much!

Rod
San Francisco