Moment of lame..er...shame....
 

Gunner wrote:

And as Im cleaning up, I pick up the gun and push the button..and
didnt hear any gas.....I discovered Id run all those crappy welds with
no gas........turned on the gas...did a couple test welds...pretty,
shiney and laid down nicely. No cleanup needed.....

Sigh....it was one of those days.......


Gunner, hanging head in shame...


Don't feel bad, I turned on the gas and fought nasty welds the other day.
Then I put a new tank of shield gas up and started over.

Wes

Moment of lame..er...shame....
 

Wes wrote:
Gunner wrote:


And as Im cleaning up, I pick up the gun and push the button..and
didnt hear any gas.....I discovered Id run all those crappy welds with
no gas........turned on the gas...did a couple test welds...pretty,
shiney and laid down nicely. No cleanup needed.....

Sigh....it was one of those days.......


Gunner, hanging head in shame...



Don't feel bad, I turned on the gas and fought nasty welds the other day.
Then I put a new tank of shield gas up and started over.

Wes


Some days it just doesn't pay to chew through the leather straps
and get out of bed...

Richard

Moment of lame..er...shame....
 

Wes wrote:

Gunner wrote:

And as Im cleaning up, I pick up the gun and push the button..and
didnt hear any gas.....I discovered Id run all those crappy welds with
no gas........turned on the gas...did a couple test welds...pretty,
shiney and laid down nicely. No cleanup needed.....

Sigh....it was one of those days.......


Gunner, hanging head in shame...

Don't feel bad, I turned on the gas and fought nasty welds the other day.
Then I put a new tank of shield gas up and started over.

Wes

You know, they put that lovely little gauge right by the valve for a
reason...

Moment of lame..er...shame....
 

On Sun, 11 May 2008 09:37:23 -0500, "Pete C."
wrote:
Wes wrote:
Gunner wrote:

And as Im cleaning up, I pick up the gun and push the button..and
didnt hear any gas.....I discovered Id run all those crappy welds with
no gas........turned on the gas...did a couple test welds...pretty,
shiney and laid down nicely. No cleanup needed.....

Sigh....it was one of those days.......

Don't feel bad, I turned on the gas and fought nasty welds the other day.
Then I put a new tank of shield gas up and started over.

You know, they put that lovely little gauge right by the valve for a
reason...

And with straight CO2 shielding gas (or a CO2 mix) it's safe to
sniff the end of the gun - if the gas isn't getting all the way there,
you'll know when your nose doesn't react.

And with all the fancy schmancy electronics on some of these feature
laden welders, you'd think one of the displays could be gas flow in
CFM - and it's always a big clue when the readout stays nailed on 0.0

(Kind of like a VCR flashing 12:00)

-- Bruce --

Moment of lame..er...shame....
 

"Pete C." wrote:

You know, they put that lovely little gauge right by the valve for a
reason...


Well, I did eventually look at it and the flow ball....

Moment of lame..er...shame....
 

Bruce L. Bergman wrote:
On Sun, 11 May 2008 09:37:23 -0500, "Pete C."
wrote:
Wes wrote:
Gunner wrote:

And as Im cleaning up, I pick up the gun and push the button..and
didnt hear any gas.....I discovered Id run all those crappy welds with
no gas........turned on the gas...did a couple test welds...pretty,
shiney and laid down nicely. No cleanup needed.....

Sigh....it was one of those days.......
Don't feel bad, I turned on the gas and fought nasty welds the other day.
Then I put a new tank of shield gas up and started over.
You know, they put that lovely little gauge right by the valve for a
reason...

And with straight CO2 shielding gas (or a CO2 mix) it's safe to
sniff the end of the gun - if the gas isn't getting all the way there,
you'll know when your nose doesn't react.

And with all the fancy schmancy electronics on some of these feature
laden welders, you'd think one of the displays could be gas flow in
CFM - and it's always a big clue when the readout stays nailed on 0.0

(Kind of like a VCR flashing 12:00)

-- Bruce --

For that matter, how hard would it be to rig a pressure switch and a
buzzer on the pre solenoid side so that once input pressure falls to a
preset cut off point, you get a beep as soon as you squeeze the trigger?
Plenty of times I've started a day with a quarter tank of gas but by 2
PM you don't think about it as your welds begin to go to crap... and
with my overhead arm and feeder, I can be far enough away that I can't
even see the tank, much less the little ball on the flowmeter.

Ought to be a cheap pressure sensing switch out there...

Stuart

Moment of lame..er...shame....
 

Stuart Wheaton wrote:

Bruce L. Bergman wrote:
On Sun, 11 May 2008 09:37:23 -0500, "Pete C."
wrote:
Wes wrote:
Gunner wrote:

And as Im cleaning up, I pick up the gun and push the button..and
didnt hear any gas.....I discovered Id run all those crappy welds with
no gas........turned on the gas...did a couple test welds...pretty,
shiney and laid down nicely. No cleanup needed.....

Sigh....it was one of those days.......
Don't feel bad, I turned on the gas and fought nasty welds the other day.
Then I put a new tank of shield gas up and started over.
You know, they put that lovely little gauge right by the valve for a
reason...

And with straight CO2 shielding gas (or a CO2 mix) it's safe to
sniff the end of the gun - if the gas isn't getting all the way there,
you'll know when your nose doesn't react.

And with all the fancy schmancy electronics on some of these feature
laden welders, you'd think one of the displays could be gas flow in
CFM - and it's always a big clue when the readout stays nailed on 0.0

(Kind of like a VCR flashing 12:00)

-- Bruce --

For that matter, how hard would it be to rig a pressure switch and a
buzzer on the pre solenoid side so that once input pressure falls to a
preset cut off point, you get a beep as soon as you squeeze the trigger?
Plenty of times I've started a day with a quarter tank of gas but by 2
PM you don't think about it as your welds begin to go to crap... and
with my overhead arm and feeder, I can be far enough away that I can't
even see the tank, much less the little ball on the flowmeter.

Ought to be a cheap pressure sensing switch out there...

Stuart

Gas pressure there is what, like 35 PSI? How about 3460K61 from
http://www.mcmaster.com for $22.77?