On an older house, the meterbox has the main breaker-60A, 240V. Upstairs at the
subpanel are

15A
40A 240 V
20A

20A
20A 240V
15A
20A

The 40A 240 is for the kitchen stove
I don't know what the 20A 240V is-there isn't anything in the unit that
would need this. If there are electrical heaters, is it possible these are
fed from one leg each? The heaters are 110. Any suggestions for what it
could be? Two 20A circuits with one neutral?

How much more can the subpanel carry? can I add a 15A and a 20 A circuit
for a garbage disposal and Dishwasher?

charles

"Charles Bishop" wrote in message
...
On an older house, the meterbox has the main breaker-60A, 240V. Upstairs
at the
subpanel are

15A
40A 240 V
20A

20A
20A 240V
15A
20A

The 40A 240 is for the kitchen stove
I don't know what the 20A 240V is-there isn't anything in the unit that
would need this. If there are electrical heaters, is it possible these are
fed from one leg each? The heaters are 110. Any suggestions for what it
could be? Two 20A circuits with one neutral?

How much more can the subpanel carry? can I add a 15A and a 20 A circuit
for a garbage disposal and Dishwasher?

charles

I have not seen a 60 amp service in a long time.

Appendix D of the NEC has residential load calculation examples. Do a load
calculation before you go to far. You might need a new service.

I am not aware of any on line resources for appendix D.

SQLit wrote:

"Charles Bishop" wrote in message
...

On an older house, the meterbox has the main breaker-60A, 240V. Upstairs

at the

subpanel are

15A
40A 240 V
20A

20A
20A 240V
15A
20A

The 40A 240 is for the kitchen stove
I don't know what the 20A 240V is-there isn't anything in the unit that
would need this. If there are electrical heaters, is it possible these are
fed from one leg each? The heaters are 110. Any suggestions for what it
could be? Two 20A circuits with one neutral?



The 20A 2-pole breaker might be for the kitchen countertop,
refrigerator, and dining room outlets.

Best regards,
Bob

Charles Bishop wrote:
On an older house, the meterbox has the main breaker-60A, 240V.
Upstairs at the
subpanel are

15A
40A 240 V
20A

20A
20A 240V
15A
20A

The 40A 240 is for the kitchen stove
I don't know what the 20A 240V is-there isn't anything in the unit
that
would need this. If there are electrical heaters, is it possible
these are
fed from one leg each? The heaters are 110. Any suggestions for what
it
could be? Two 20A circuits with one neutral?

How much more can the subpanel carry? can I add a 15A and a 20 A
circuit
for a garbage disposal and Dishwasher?

charles

Around here it's rare to find electric heating in a house with a 60-A
service. By the time electric heating became (misguidedly) common,
100-A or 150-A services were the norm.

Is that 20A dual-pole breaker connected to cable? If not, it may have
never been used. Maybe it came with the panel or was installed
needlessly.

Consider using it for the DW and disposal, assuming they're near each
other. Run 12/3 from the panel to a box in the vicinity of the
appliances then run 12/2 to each of them.

Make very sure that it actually feeds from different legs (ie, that it
really is 240). But see if your jurisdiction requires gfci for new
dishwasher or disposal hookups. Around here, I believe it does not.

Not that you asked, but while I was at it I'd also check that that 20A
circuits are really wired with 12 gauge, and I'd see if new breakers,
including gfci and afci, are available for the old panel. If not, you
may find that you'll want to replace it sooner rather than later.

Chip C
Toronto