How do I remove this faucet cartridge
 

My faucet is leaking, but when I remove the handle, I can't see how to get the cartridge out.

It looks like this: https://www.flickr.com/gp/7865232@N08/Qc2r91

I tried using a wrench on the nut-shaped top of the metal housing, but it would not budge in either direction.

Am I missing something simple here?

Thanks.

-J

How do I remove this faucet cartridge
 

The linked picture (of a nice clean cartridge) is actually the cold tap. It's the hot tap that's leaking, and the picture of that is not as pretty: lots of black gunk - probably from a corroded o-ring.

-J

How do I remove this faucet cartridge
 

On 10/01/2015 09:07 AM, J wrote:
My faucet is leaking, but when I remove the handle, I can't see how to get the cartridge out.

It looks like this: https://www.flickr.com/gp/7865232@N08/Qc2r91

I tried using a wrench on the nut-shaped top of the metal housing, but it would not budge in either direction.

Am I missing something simple here?

Thanks.

-J





It looks to be in good condition so it should come off with a wrench .
Use one of good quality that grips on all six sides and turn it counter
clockwise.

Though more than likely quite tight, it should come apart.

How do I remove this faucet cartridge
 

On 10/1/2015 10:07 AM, J wrote:
My faucet is leaking, but when I remove the handle, I can't see how to get the cartridge out.

It looks like this: https://www.flickr.com/gp/7865232@N08/Qc2r91

I tried using a wrench on the nut-shaped top of the metal housing, but it would not budge in either direction.

Am I missing something simple here?

Thanks.

-J

Don't know the specific cartridge. Know that Moen's often require
cartridge puller.

Sometimes best to call a plumber. I did for Moen cartridge in my 35
year old shower as I learned from year before pulling one in bathtub
without puller that I was in danger of breaking pipes.

DIY, maybe find a utube video on brand.

How do I remove this faucet cartridge
 

On 10/01/2015 9:15 AM, philo wrote:
On 10/01/2015 09:07 AM, J wrote:
My faucet is leaking, but when I remove the handle, I can't see how to
get the cartridge out.

It looks like this: https://www.flickr.com/gp/7865232@N08/Qc2r91

I tried using a wrench on the nut-shaped top of the metal housing, but
it would not budge in either direction.

Am I missing something simple here?
....


It looks to be in good condition so it should come off with a wrench .
Use one of good quality that grips on all six sides and turn it counter
clockwise.

Though more than likely quite tight, it should come apart.

+1 I'd suggest a deepwell socket (like spark plug socket, for example)
if the stem isn't too long. If not a good box end, do _not_ use an
adjustable ("crescent") wrench or a sorry open end or you'll risk
rounding it off.

An impact or two on the end to apply some high impulse shock may do
wonders...

--

How do I remove this faucet cartridge
 

On 10/01/2015 9:29 AM, dpb wrote:
....

An impact or two on the end to apply some high impulse shock may do
wonders...

On the end of the _wrench_, of course, not the valve stem or... :)

--

How do I remove this faucet cartridge
 

On Thursday, October 1, 2015 at 10:31:59 AM UTC-4, dpb wrote:
On 10/01/2015 9:29 AM, dpb wrote:
...

An impact or two on the end to apply some high impulse shock may do
wonders...

On the end of the _wrench_, of course, not the valve stem or... :)

--

yes,
I used a good deep socket and rachet and the problem I had was that the entire assembly turned insted of loosening the cartrage.

So I tried a small electric impact wrench. It came out in 1 second.

I strongly recommend an impact wrench for this job.

Not becasue it needs a lot of torque, but because it will loosen stuff without spinning the whole assembly.

Mark

How do I remove this faucet cartridge
 

On Thursday, October 1, 2015 at 11:05:50 AM UTC-4, wrote:
On Thursday, October 1, 2015 at 10:31:59 AM UTC-4, dpb wrote:
On 10/01/2015 9:29 AM, dpb wrote:
...

An impact or two on the end to apply some high impulse shock may do
wonders...

On the end of the _wrench_, of course, not the valve stem or... :)

--

yes,
I used a good deep socket and rachet and the problem I had was that the entire assembly turned insted of loosening the cartrage.

So I tried a small electric impact wrench. It came out in 1 second.

I strongly recommend an impact wrench for this job.

Not becasue it needs a lot of torque, but because it will loosen stuff without spinning the whole assembly.

Mark

I forgot to add.. I used a Danco brand replacement and it leaked again in a few months. Went through a few Dancos and they leaked after a short time. Now I tried a real American Standard. So far it is holding but it has only been a few days.

Mark

How do I remove this faucet cartridge
 

Thanks for all the quick advice. I'll see if I can find a deep socket that fits. If not, I'll try the helpful neighbor, and give it a few whacks - the wrench, not the neighbor ;-)

How do I remove this faucet cartridge
 

On Thu, 1 Oct 2015 08:34:21 -0700 (PDT), J wrote:

Thanks for all the quick advice. I'll see if I can find a deep socket that fits. If not, I'll try the helpful neighbor, and give it a few whacks - the wrench, not the neighbor ;-)

In addition, you can try soaking the nut with penetrating fluid (maybe
overnight) and tap it a few times -- allowing the fluid to get into
the threads.

How do I remove this faucet cartridge
 

Thanks you guys!

I finally had the time to look through my tools (the slow drip was not forcing me to do anything quickly) and I found a deep socket that fit the bill (I mean, the nut) - 15/16". Better yet, the handle of the socket wrench was very long (actually an old-style torque wrench). Now, I understand the physics of torque = force x moment-arm, but I was still surprised at how easily the thing turned once I had the proper tools. So easily that I think I had to have loosened it with the crescent wrench. I mean, when I was using the crescent wrench, I seemed to be physically deforming the nut, with nothing budging.

Anyway, I was able to get the replacement cartridge at home despot (under $8) and the drip is no more. Yay!

-J

How do I remove this faucet cartridge
 

On 10/15/2015 2:06 PM, J wrote:
Thanks you guys!

I finally had the time to look through my tools (the slow drip was
not forcing me to do anything quickly) and I found a deep socket that fit
the bill (I mean, the nut) - 15/16". Better yet, the handle of the
socket wrench was very long (actually an old-style torque wrench). Now,
I understand the physics of torque = force x moment-arm, but I was still
surprised at how easily the thing turned once I had the proper tools. ...

Indeed, it's "the secret of the trade" as often as not...

--