Need to replace my condenser fan motor in my heat pump. The current one is
1100 RPM. The Tech support at Grainger's recommended one that is 1075 RPM.
Would this make a difference or harm the compressor due to the slightly
slower rotation?

R

On Jan 15, 12:33*pm, "Roanin" wrote:
Need to replace my condenser fan motor in my heat pump. *The current one is
1100 RPM. The Tech support at Grainger's recommended one that is 1075 RPM..
Would this make a difference or harm the compressor due to the slightly
slower rotation?

R

not likely to do damage

On 1/15/2013 10:33 AM, Roanin wrote:
Need to replace my condenser fan motor in my heat pump. The current one is
1100 RPM. The Tech support at Grainger's recommended one that is 1075 RPM.
Would this make a difference or harm the compressor due to the slightly
slower rotation?

R


I have to wonder why you need to replace it? Did the motor freeze up, or
is it vibrating wildly?

The reason I ask is we have owned our current place for 6 years. About 2
years after moving in, the fan on the heat pump froze up. I had noticed
the fan and motor were vibrating some since we moved in and figured it
had always done that and was really ok.

We had a local professional replace the motor. It still had the
vibration, but ran really well. Last fall, the motor began to vibrate
wildly and eventually stopped running, but was still free to turn.

We had a different company cone look at and the wires going to the motor
had burned up. The bearings in the fan were destroyed and oil had leaked
out.

The service man replaced the motor and commented on the vibration.
should be NO vibration. I had removed a length of small round wooden
dowel from the bottom of the case and showed the service man. I
questioned him if someone running that stick into the fan could cause
the out of balance vibration and he concurred and ordered up a new fan.

The old fan looked perfect, but I replaced the 4 bladed fan when the new
one came in. No vibration at all. I examined the old fan and could see a
place on the corner of one blade where the previous owner had
straightened out a bent place. So the stick had actually hit a blade.

The old fan was still statically balanced, but because the curvature of
the repaired blade was not the same as the other three blades, it was
not dynamically balanced. There was either too much pitch or not enough.
I could not tell by looking which it was.

So, in conclusion, you may need to also replace the fan as well as the
motor.

Good luck, Paul

"Paul Drahn" wrote in message
...
On 1/15/2013 10:33 AM, Roanin wrote:
Need to replace my condenser fan motor in my heat pump. The current one
is
1100 RPM. The Tech support at Grainger's recommended one that is 1075
RPM.
Would this make a difference or harm the compressor due to the slightly
slower rotation?

R


I have to wonder why you need to replace it? Did the motor freeze up, or
is it vibrating wildly?

The reason I ask is we have owned our current place for 6 years. About 2
years after moving in, the fan on the heat pump froze up. I had noticed
the fan and motor were vibrating some since we moved in and figured it had
always done that and was really ok.

We had a local professional replace the motor. It still had the vibration,
but ran really well. Last fall, the motor began to vibrate wildly and
eventually stopped running, but was still free to turn.

We had a different company cone look at and the wires going to the motor
had burned up. The bearings in the fan were destroyed and oil had leaked
out.

The service man replaced the motor and commented on the vibration. should
be NO vibration. I had removed a length of small round wooden dowel from
the bottom of the case and showed the service man. I questioned him if
someone running that stick into the fan could cause the out of balance
vibration and he concurred and ordered up a new fan.

The old fan looked perfect, but I replaced the 4 bladed fan when the new
one came in. No vibration at all. I examined the old fan and could see a
place on the corner of one blade where the previous owner had straightened
out a bent place. So the stick had actually hit a blade.

The old fan was still statically balanced, but because the curvature of
the repaired blade was not the same as the other three blades, it was not
dynamically balanced. There was either too much pitch or not enough. I
could not tell by looking which it was.

So, in conclusion, you may need to also replace the fan as well as the
motor.

Good luck, Paul

Replacing it because it is squealing very loud after running for about 20
minutes. You bump it on the top and it quits for a second then starts again.
No vibration.

R

On 1/15/2013 1:59 PM, Roanin wrote:
"Paul Drahn" wrote in message
...
On 1/15/2013 10:33 AM, Roanin wrote:
Need to replace my condenser fan motor in my heat pump. The current one
is
1100 RPM. The Tech support at Grainger's recommended one that is 1075
RPM.
Would this make a difference or harm the compressor due to the slightly
slower rotation?

R


I have to wonder why you need to replace it? Did the motor freeze up, or
is it vibrating wildly?

The reason I ask is we have owned our current place for 6 years. About 2
years after moving in, the fan on the heat pump froze up. I had noticed
the fan and motor were vibrating some since we moved in and figured it had
always done that and was really ok.

We had a local professional replace the motor. It still had the vibration,
but ran really well. Last fall, the motor began to vibrate wildly and
eventually stopped running, but was still free to turn.

We had a different company cone look at and the wires going to the motor
had burned up. The bearings in the fan were destroyed and oil had leaked
out.

The service man replaced the motor and commented on the vibration. should
be NO vibration. I had removed a length of small round wooden dowel from
the bottom of the case and showed the service man. I questioned him if
someone running that stick into the fan could cause the out of balance
vibration and he concurred and ordered up a new fan.

The old fan looked perfect, but I replaced the 4 bladed fan when the new
one came in. No vibration at all. I examined the old fan and could see a
place on the corner of one blade where the previous owner had straightened
out a bent place. So the stick had actually hit a blade.

The old fan was still statically balanced, but because the curvature of
the repaired blade was not the same as the other three blades, it was not
dynamically balanced. There was either too much pitch or not enough. I
could not tell by looking which it was.

So, in conclusion, you may need to also replace the fan as well as the
motor.

Good luck, Paul

Replacing it because it is squealing very loud after running for about 20
minutes. You bump it on the top and it quits for a second then starts again.
No vibration.

R



bad bearings. eventually it will seize up, causing further damage. pull
the fuse until you get it replaced.

Another perhaps less expensive option might be to have the motor rebuilt. Many motors nowadays can't be rebuilt, but it might be worth your while to look on that motor for information about it, and phone around to the electric motor rewinding businesses in your area to see what they say.

If you have a digital camera, you can e-mail a picture of it to the motor rebuilding shops, and they might be able to tell if they can rebuild it just from the picture.

I agree that a small difference in the fan speed won't affect or harm your heating system.

On Jan 16, 12:59*am, nestork wrote:
Another perhaps less expensive option might be to have the motor
rebuilt. *Many motors nowadays can't be rebuilt, but it might be worth
your while to look on that motor for information about it, and phone
around to the electric motor rewinding businesses in your area to see
what they say.

If you have a digital camera, you can e-mail a picture of it to the
motor rebuilding shops, and they might be able to tell if they can
rebuild it just from the picture.

I agree that a small difference in the fan speed won't affect or harm
your heating system.

--
nestork

if its a von weise motor, that company imploded. moved overseas.

parts order time near 2 years minimum order 3 grand or other insane
amount, required prepaid.

how insane is that. grainger quit selling von weise motors when they
made those changes.

the machines i service for a living used von weise motors, and the
motor parts were affordable.

now its all new motors and has cost me big bucks, since the machines i
service are mostly under maintence

On 1/15/2013 12:59 PM, Roanin wrote:
"Paul wrote in message
...
On 1/15/2013 10:33 AM, Roanin wrote:
Need to replace my condenser fan motor in my heat pump. The current one
is
1100 RPM. The Tech support at Grainger's recommended one that is 1075
RPM.
Would this make a difference or harm the compressor due to the slightly
slower rotation?

R


I have to wonder why you need to replace it? Did the motor freeze up, or
is it vibrating wildly?

The reason I ask is we have owned our current place for 6 years. About 2
years after moving in, the fan on the heat pump froze up. I had noticed
the fan and motor were vibrating some since we moved in and figured it had
always done that and was really ok.

We had a local professional replace the motor. It still had the vibration,
but ran really well. Last fall, the motor began to vibrate wildly and
eventually stopped running, but was still free to turn.

We had a different company cone look at and the wires going to the motor
had burned up. The bearings in the fan were destroyed and oil had leaked
out.

The service man replaced the motor and commented on the vibration. should
be NO vibration. I had removed a length of small round wooden dowel from
the bottom of the case and showed the service man. I questioned him if
someone running that stick into the fan could cause the out of balance
vibration and he concurred and ordered up a new fan.

The old fan looked perfect, but I replaced the 4 bladed fan when the new
one came in. No vibration at all. I examined the old fan and could see a
place on the corner of one blade where the previous owner had straightened
out a bent place. So the stick had actually hit a blade.

The old fan was still statically balanced, but because the curvature of
the repaired blade was not the same as the other three blades, it was not
dynamically balanced. There was either too much pitch or not enough. I
could not tell by looking which it was.

So, in conclusion, you may need to also replace the fan as well as the
motor.

Good luck, Paul

Replacing it because it is squealing very loud after running for about 20
minutes. You bump it on the top and it quits for a second then starts again.
No vibration.

R


Sure sign one of the oil seals has failed and let the oil leak out. As
was explained to me, the top and bottom bearings both have a small
amount of oil in a reservoir protected by oil seals. With age and heat,
the seals crack and let the oil escape.

If you look at the fan hub you will see oil and dirt. Be sure to clean
this off so you can detect the oil leak next time! Also be sure the new
motor turns in the correct direction. My service guy had it wrong and
had to unbutton the fan screen and reverse two wires.

To the other posters, these motors are designed to be suspended
vertically and have no way to replace seals and oil.

Paul

I havn't seen anything like this, in the years I've
worked on motors. I've seen bronze bearings,
some with oil ports, and some not. The ones
without oil ports can still be oiled, sometimes.

Christopher A. Young
Learn more about Jesus
www.lds.org
..

"Paul Drahn" wrote in message
...
Sure sign one of the oil seals has failed and let the oil leak out. As
was explained to me, the top and bottom bearings both have a small
amount of oil in a reservoir protected by oil seals. With age and heat,
the seals crack and let the oil escape.

If you look at the fan hub you will see oil and dirt. Be sure to clean
this off so you can detect the oil leak next time! Also be sure the new
motor turns in the correct direction. My service guy had it wrong and
had to unbutton the fan screen and reverse two wires.

To the other posters, these motors are designed to be suspended
vertically and have no way to replace seals and oil.

Paul

Agreed, you should try oiling it first..
Also even if the fan blade is fine, you may want to get anew one because it may be difficult to remove the exiting blade from the motor.
Be sure to keep track to the direction of spin of the motor CW or CCW , the direction of spin the blade is designed for, the pitch of the blade and the HP rating of the motor.
Also pay attention to the location of the blade how far on the shaft it is.
I'm a DYI guy and successfully replaced the blade and motor on my heat pump.
Just pay attention to the details.
Another detail is the routing of the wires, they must be securely attached so they don,t droop over time and get clipped by the blade.

Mark

A squirt of oil might make the motor last several more years. Can't hurt, at
least to try.
Agreed, get a new blade. Sometimes even if you can get the old bade off,
it's not going to fit the new motor. And it may be out of balance.
Being Mormon, I don't drink, and so don't get DYI trouble with the cops.
UV resistant nylon tie straps are good, for wires. Clip the end off the
wrap, so the end doesn't droop.

Christopher A. Young
Learn more about Jesus
www.lds.org
..

wrote in message
...

Agreed, you should try oiling it first..
Also even if the fan blade is fine, you may want to get anew one because it
may be difficult to remove the exiting blade from the motor.
Be sure to keep track to the direction of spin of the motor CW or CCW , the
direction of spin the blade is designed for, the pitch of the blade and the
HP rating of the motor.
Also pay attention to the location of the blade how far on the shaft it is.
I'm a DYI guy and successfully replaced the blade and motor on my heat pump.
Just pay attention to the details.
Another detail is the routing of the wires, they must be securely attached
so they don,t droop over time and get clipped by the blade.

Mark