An extension tube for 3/8" copper waterr tube
I need an extension tube for 3/8" copper waterr tube
I took out my kitchen faucet and the tubes on the new one doesnt' reach the pipes coming from the wall. One is about 1/2" too short, and the other might possibly reach, but it requires bending, and I'm afraid I'll kink it. Most of the tubing is behind the sink bowl and even the part that isn't is hard to work with because it's 18 inches or so into the cabinet. What do people do in this situation? I could use plain old 3/8" copper tubing and a compression fitting at one end. The other end is the line from the faucet, which currently has a ferrule and a nut on it, and is just waiting for something male to attach to. But I don't think there is like that. I also could flare the end if that would help but I don't see how it would. I've been to the store and good ole HDepot had lines, with IP at one end, and a compression fitting at the other (although the label seemed to say that it was compression at both ends.) I also have a pair of lines I bought earlier when I had no idea what I wanted (but they were 1 dollar a piece), with IP at both ends, 1/2 and 3/8 although the label says 1/2" IP at one end and 3/8" compression at the other. Is there something wrong with my undrestanding, that even though they are different brands, I keep seeing one end as IP even though the labels on each call the end "comp". Thanks. |
An extension tube for 3/8" copper waterr tube
On Wed, 16 Feb 2011 22:18:29 -0500, mm
wrote: I need an extension tube for 3/8" copper waterr tube I took out my kitchen faucet and the tubes on the new one doesnt' reach the pipes coming from the wall. One is about 1/2" too short, and the other might possibly reach, but it requires bending, and I'm afraid I'll kink it. Most of the tubing is behind the sink bowl and even the part that isn't is hard to work with because it's 18 inches or so into the cabinet. What do people do in this situation? I could use plain old 3/8" copper tubing and a compression fitting at one end. The other end is the line from the faucet, which currently has a ferrule and a nut on it, and is just waiting for something male to attach to. But I don't think there is like that. I just realized I could use a compression union, but that means 4 more compression fittings under the sink. Isn't there a better way to do this? I saw a swaging tool for sale, that would enlarge one of the two tubes so the other could fit inside it, and be soldered. Would that be okay? A good idea? Hard to do? Copper tubing splits before it's big enough? I'd enlarge the new piece of tubing and slide it over the piece that is under the sink. Soldering with a torch will set fire to the sink cabinet? MM I also could flare the end if that would help but I don't see how it would. I've been to the store and good ole HDepot had lines, with IP at one end, and a compression fitting at the other (although the label seemed to say that it was compression at both ends.) I also have a pair of lines I bought earlier when I had no idea what I wanted (but they were 1 dollar a piece), with IP at both ends, 1/2 and 3/8 although the label says 1/2" IP at one end and 3/8" compression at the other. Is there something wrong with my undrestanding, that even though they are different brands, I keep seeing one end as IP even though the labels on each call the end "comp". Thanks. |
An extension tube for 3/8" copper waterr tube
On Feb 16, 10:42*pm, mm wrote:
On Wed, 16 Feb 2011 22:18:29 -0500, mm wrote: I need an extension tube for 3/8" copper waterr tube I took out my kitchen faucet and the tubes on the new one doesnt' reach the pipes coming from the wall. One is about 1/2" too short, and the other might possibly reach, but it requires bending, and I'm afraid I'll kink it. *Most of the tubing is behind the sink bowl and even the part that isn't is hard to work with because it's 18 inches or so into the cabinet. What do people do in this situation? I could use plain old 3/8" copper tubing and a compression fitting at one end. * The other end is the line from the faucet, which currently has a ferrule and a nut on it, and is just waiting for something male to attach to. *But I don't think there is like that. I just realized I could use a compression union, but that means 4 more compression fittings under the sink. *Isn't there a better way to do this? I saw a swaging tool for sale, that would enlarge one of the two tubes so the other could fit inside it, and be soldered. *Would that be okay? *A good idea? * Hard to do? *Copper tubing splits before it's big enough? * I'd enlarge the new piece of tubing and slide it over the piece that is under the sink. * Soldering with a torch will set fire to the sink cabinet? MM I also could flare the end if that would help but I don't see how it would. I've been to the store and good ole HDepot had lines, with IP at one end, and a compression fitting at the other (although the label seemed to say that it was compression at both ends.) * I also have a pair of lines I bought earlier when I had no idea what I wanted (but they were 1 dollar a piece), with IP at both ends, 1/2 and 3/8 although the label says 1/2" IP at one end and 3/8" compression at the other. *Is there something wrong with my undrestanding, that even though they are different brands, I keep seeing one end as IP even though the labels on each call the end "comp". Thanks.- Hide quoted text - - Show quoted text -- Hide quoted text - - Show quoted text - I thought I've seen those braided hoses that has 3/8" compression at both ends,one end male, one end female, basically an extension pipe. That would work for you. I don't think HD is going to have that. Most likely a plumbing supply store. |
An extension tube for 3/8" copper waterr tube
On Wed, 16 Feb 2011 20:06:14 -0800 (PST), Mikepier
wrote: On Feb 16, 10:42*pm, mm wrote: On Wed, 16 Feb 2011 22:18:29 -0500, mm wrote: I need an extension tube for 3/8" copper waterr tube I took out my kitchen faucet and the tubes on the new one doesnt' reach the pipes coming from the wall. One is about 1/2" too short, and the other might possibly reach, but it requires bending, and I'm afraid I'll kink it. *Most of the tubing is behind the sink bowl and even the part that isn't is hard to work with because it's 18 inches or so into the cabinet. What do people do in this situation? I could use plain old 3/8" copper tubing and a compression fitting at one end. * The other end is the line from the faucet, which currently has a ferrule and a nut on it, and is just waiting for something male to attach to. *But I don't think there is like that. I just realized I could use a compression union, but that means 4 more compression fittings under the sink. *Isn't there a better way to do this? I saw a swaging tool for sale, that would enlarge one of the two tubes so the other could fit inside it, and be soldered. *Would that be okay? *A good idea? * Hard to do? *Copper tubing splits before it's big enough? * I'd enlarge the new piece of tubing and slide it over the piece that is under the sink. * Soldering with a torch will set fire to the sink cabinet? MM I also could flare the end if that would help but I don't see how it would. I've been to the store and good ole HDepot had lines, with IP at one end, and a compression fitting at the other (although the label seemed to say that it was compression at both ends.) * I also have a pair of lines I bought earlier when I had no idea what I wanted (but they were 1 dollar a piece), with IP at both ends, 1/2 and 3/8 although the label says 1/2" IP at one end and 3/8" compression at the other. *Is there something wrong with my undrestanding, that even though they are different brands, I keep seeing one end as IP even though the labels on each call the end "comp". Thanks.- Hide quoted text - - Show quoted text -- Hide quoted text - - Show quoted text - I thought I've seen those braided hoses that has 3/8" compression at both ends,one end male, one end female, basically an extension pipe. That would work for you. I don't think HD is going to have that. Most likely a plumbing supply store. Thanks. I'll try a plumbing store tomorrow. |
An extension tube for 3/8" copper waterr tube
On Wed, 16 Feb 2011 22:18:29 -0500, mm
wrote: I need an extension tube for 3/8" copper waterr tube I took out my kitchen faucet and the tubes on the new one doesnt' reach the pipes coming from the wall. One is about 1/2" too short, and the other might possibly reach, but it requires bending, and I'm afraid I'll kink it. Most of the tubing is behind the sink bowl and even the part that isn't is hard to work with because it's 18 inches or so into the cabinet. What do people do in this situation? I could use plain old 3/8" copper tubing and a compression fitting at one end. The other end is the line from the faucet, which currently has a ferrule and a nut on it, and is just waiting for something male to attach to. But I don't think there is like that. I also could flare the end if that would help but I don't see how it would. I've been to the store and good ole HDepot had lines, with IP at one end, and a compression fitting at the other (although the label seemed to say that it was compression at both ends.) I also have a pair of lines I bought earlier when I had no idea what I wanted (but they were 1 dollar a piece), with IP at both ends, 1/2 and 3/8 although the label says 1/2" IP at one end and 3/8" compression at the other. Is there something wrong with my undrestanding, that even though they are different brands, I keep seeing one end as IP even though the labels on each call the end "comp". Thanks. The RIGHT way to do it is to extend the 1/2'" copper to the right position so your 3/8" tubing fits properly |
An extension tube for 3/8" copper waterr tube
|
An extension tube for 3/8" copper waterr tube
On Feb 16, 9:18*pm, mm wrote:
I need an extension tube for 3/8" copper waterr tube No you don't. snip What do people do in this situation? See below. snip I've been to the store and good ole HDepot had lines, with IP at one end, and a compression fitting at the other (although the label seemed to say that it was compression at both ends.) * snip You have the proper stuff now. Take the input lines off the faucet and the fix is obvious. Joe Joe |
An extension tube for 3/8" copper waterr tube
|
All times are GMT +1. The time now is 03:29 AM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter