|
OT - Phillips Head Screws On Brake Rotors
The recent thread about impact wrenches got me thinking...
I need to change the rotors on my Honda Oddessy. They have 2 large phillips head screws countersunk into the rotors which have to be removed before the rotors will come off. I don't know if they are the original rotors (70K on the van, I've had it since 40K with the same rotors) but I'm thinking that with all the heat generated by braking, they might not be the easiest screws to remove. I didn't want to try backing out the screws with a huge phillips head driver for fear of damaging them, then having to drill them out, etc. Before I take everything apart (again) does anybody have any thoughts on the best way to remove the screws, assuming a big screw driver doesn't work? |
OT - Phillips Head Screws On Brake Rotors
On Aug 7, 1:45*pm, DerbyDad03 wrote:
The recent thread about impact wrenches got me thinking... I need to change the rotors on my Honda Oddessy. They have *2 large phillips head screws countersunk into the rotors which have to be removed before the rotors will come off. I don't know if they are the original rotors (70K on the van, I've had it since 40K with the same rotors) but I'm thinking that with all the heat generated by braking, they might not be the easiest screws to remove. I didn't want to try backing out the screws with a huge phillips head driver for fear of damaging them, then having to drill them out, etc. Before I take everything apart (again) does anybody have any thoughts on the best way to remove the screws, assuming a big screw driver doesn't work? 2 words: impact driver http://www.kk.org/cooltools/archives/000723.php |
OT - Phillips Head Screws On Brake Rotors
DerbyDad03 wrote:
The recent thread about impact wrenches got me thinking... I need to change the rotors on my Honda Oddessy. They have 2 large phillips head screws countersunk into the rotors which have to be removed before the rotors will come off. I don't know if they are the original rotors (70K on the van, I've had it since 40K with the same rotors) but I'm thinking that with all the heat generated by braking, they might not be the easiest screws to remove. I didn't want to try backing out the screws with a huge phillips head driver for fear of damaging them, then having to drill them out, etc. Before I take everything apart (again) does anybody have any thoughts on the best way to remove the screws, assuming a big screw driver doesn't work? Give 'em a dose of something from the auto parts store that loosens rusted-shut bolts. Can't hurt. |
OT - Phillips Head Screws On Brake Rotors
On Fri, 7 Aug 2009 11:53:15 -0700 (PDT), Eric in North TX
wrote: On Aug 7, 1:45*pm, DerbyDad03 wrote: The recent thread about impact wrenches got me thinking... I need to change the rotors on my Honda Oddessy. They have *2 large phillips head screws countersunk into the rotors which have to be removed before the rotors will come off. I don't know if they are the original rotors (70K on the van, I've had it since 40K with the same rotors) but I'm thinking that with all the heat generated by braking, they might not be the easiest screws to remove. I didn't want to try backing out the screws with a huge phillips head driver for fear of damaging them, then having to drill them out, etc. Before I take everything apart (again) does anybody have any thoughts on the best way to remove the screws, assuming a big screw driver doesn't work? 2 words: impact driver http://www.kk.org/cooltools/archives/000723.php Good answer! And a pre-soak of the screws with a penetrating liquid (maybe overnight). |
OT - Phillips Head Screws On Brake Rotors
DerbyDad03 wrote:
The recent thread about impact wrenches got me thinking... I need to change the rotors on my Honda Oddessy. They have 2 large phillips head screws countersunk into the rotors which have to be removed before the rotors will come off. I don't know if they are the original rotors (70K on the van, I've had it since 40K with the same rotors) but I'm thinking that with all the heat generated by braking, they might not be the easiest screws to remove. I didn't want to try backing out the screws with a huge phillips head driver for fear of damaging them, then having to drill them out, etc. Before I take everything apart (again) does anybody have any thoughts on the best way to remove the screws, assuming a big screw driver doesn't work? If you don't have an impact driver, still do what HeyBub advises, insert the screwdriver in the screw and then a sharp tap to the head of the screwdriver handle with a hammer. This can help to free it. |
OT - Phillips Head Screws On Brake Rotors
"Clot" wrote in message ... DerbyDad03 wrote: The recent thread about impact wrenches got me thinking... I need to change the rotors on my Honda Oddessy. They have 2 large phillips head screws countersunk into the rotors which have to be removed before the rotors will come off. I don't know if they are the original rotors (70K on the van, I've had it since 40K with the same rotors) but I'm thinking that with all the heat generated by braking, they might not be the easiest screws to remove. I didn't want to try backing out the screws with a huge phillips head driver for fear of damaging them, then having to drill them out, etc. Before I take everything apart (again) does anybody have any thoughts on the best way to remove the screws, assuming a big screw driver doesn't work? If you have a torch handy, heat the area around the screw head then throw cold water on it. The quick expansion and contraction will loosen the screw. |
OT - Phillips Head Screws On Brake Rotors
On Aug 7, 3:04*pm, Oren wrote:
On Fri, 7 Aug 2009 11:53:15 -0700 (PDT), Eric in North TX wrote: On Aug 7, 1:45*pm, DerbyDad03 wrote: The recent thread about impact wrenches got me thinking... I need to change the rotors on my Honda Oddessy. They have *2 large phillips head screws countersunk into the rotors which have to be removed before the rotors will come off. I don't know if they are the original rotors (70K on the van, I've had it since 40K with the same rotors) but I'm thinking that with all the heat generated by braking, they might not be the easiest screws to remove. I didn't want to try backing out the screws with a huge phillips head driver for fear of damaging them, then having to drill them out, etc. Before I take everything apart (again) does anybody have any thoughts on the best way to remove the screws, assuming a big screw driver doesn't work? 2 words: impact driver http://www.kk.org/cooltools/archives/000723.php Good answer! And a pre-soak of the screws with a penetrating liquid (maybe overnight). What they said. The hand impact, a properly fitting Phillips bit, and a BFH is the Right Tool For The Job. Requred to remove stubborn (car) door hinge screws, as well. Nothing else is likely to work. Good news is, you probably already have a BFH, and if you don't have an impact driver, they are not expensive. good luck nate |
OT - Phillips Head Screws On Brake Rotors
On Aug 7, 2:53*pm, Eric in North TX wrote:
On Aug 7, 1:45*pm, DerbyDad03 wrote: The recent thread about impact wrenches got me thinking... I need to change the rotors on my Honda Oddessy. They have *2 large phillips head screws countersunk into the rotors which have to be removed before the rotors will come off. I don't know if they are the original rotors (70K on the van, I've had it since 40K with the same rotors) but I'm thinking that with all the heat generated by braking, they might not be the easiest screws to remove. I didn't want to try backing out the screws with a huge phillips head driver for fear of damaging them, then having to drill them out, etc. Before I take everything apart (again) does anybody have any thoughts on the best way to remove the screws, assuming a big screw driver doesn't work? 2 words: impact driverhttp://www.kk.org/cooltools/archives/000723.php I'll look into it, but... From the website... "although it takes some skill to keep it on the bolt when you hammer it." And they seem to be talking about a socket over a bolt, not a bit in a phillips head screw. It's hard to tell the size of the screwdriver bolts from the pictures, but none of them look big enough to fit securely in the large philips head screws on my rotor. I'll stop by Sears and see what they look like close up. Thanks! |
OT - Phillips Head Screws On Brake Rotors
On Fri, 7 Aug 2009 13:57:23 -0700 (PDT), DerbyDad03
wrote: On Aug 7, 2:53*pm, Eric in North TX wrote: On Aug 7, 1:45*pm, DerbyDad03 wrote: The recent thread about impact wrenches got me thinking... I need to change the rotors on my Honda Oddessy. They have *2 large phillips head screws countersunk into the rotors which have to be removed before the rotors will come off. I don't know if they are the original rotors (70K on the van, I've had it since 40K with the same rotors) but I'm thinking that with all the heat generated by braking, they might not be the easiest screws to remove. I didn't want to try backing out the screws with a huge phillips head driver for fear of damaging them, then having to drill them out, etc. Before I take everything apart (again) does anybody have any thoughts on the best way to remove the screws, assuming a big screw driver doesn't work? 2 words: impact driverhttp://www.kk.org/cooltools/archives/000723.php I'll look into it, but... From the website... "although it takes some skill to keep it on the bolt when you hammer it." And they seem to be talking about a socket over a bolt, not a bit in a phillips head screw. It's hard to tell the size of the screwdriver bolts from the pictures, but none of them look big enough to fit securely in the large philips head screws on my rotor. I'll stop by Sears and see what they look like close up. Thanks! My wrench came from Sears many years ago. "6 pc. impact driver set lets you free frozen or rusted screws. Each hammer blow develops 200 ft. lb. of torque. Includes 1/2 in. sq. drive tool, bit holder, 3/8 in. slotted and Nos. 2, 3 and 4 Phillips bits." Same as this pic: http://www.toolnet.co.za/images/47641.jpg |
OT - Phillips Head Screws On Brake Rotors
Oren wrote:
On Fri, 7 Aug 2009 13:57:23 -0700 (PDT), DerbyDad03 wrote: On Aug 7, 2:53 pm, Eric in North TX wrote: On Aug 7, 1:45 pm, DerbyDad03 wrote: The recent thread about impact wrenches got me thinking... I need to change the rotors on my Honda Oddessy. They have 2 large phillips head screws countersunk into the rotors which have to be removed before the rotors will come off. I don't know if they are the original rotors (70K on the van, I've had it since 40K with the same rotors) but I'm thinking that with all the heat generated by braking, they might not be the easiest screws to remove. I didn't want to try backing out the screws with a huge phillips head driver for fear of damaging them, then having to drill them out, etc. Before I take everything apart (again) does anybody have any thoughts on the best way to remove the screws, assuming a big screw driver doesn't work? 2 words: impact driverhttp://www.kk.org/cooltools/archives/000723.php I'll look into it, but... From the website... "although it takes some skill to keep it on the bolt when you hammer it." And they seem to be talking about a socket over a bolt, not a bit in a phillips head screw. It's hard to tell the size of the screwdriver bolts from the pictures, but none of them look big enough to fit securely in the large philips head screws on my rotor. I'll stop by Sears and see what they look like close up. Thanks! My wrench came from Sears many years ago. "6 pc. impact driver set lets you free frozen or rusted screws. Each hammer blow develops 200 ft. lb. of torque. Includes 1/2 in. sq. drive tool, bit holder, 3/8 in. slotted and Nos. 2, 3 and 4 Phillips bits." Same as this pic: http://www.toolnet.co.za/images/47641.jpg I have removed them many times and impact(same Sears set)is the way to go. Often they only need a tap and comes out easy. But then... GA |
OT - Phillips Head Screws On Brake Rotors
On Fri, 07 Aug 2009 11:53:15 -0700, Eric in North TX wrote:
On Aug 7, 1:45Â*pm, DerbyDad03 wrote: The recent thread about impact wrenches got me thinking... I need to change the rotors on my Honda Oddessy. They have Â*2 large phillips head screws countersunk into the rotors which have to be removed before the rotors will come off. I don't know if they are the original rotors (70K on the van, I've had it since 40K with the same rotors) but I'm thinking that with all the heat generated by braking, they might not be the easiest screws to remove. I didn't want to try backing out the screws with a huge phillips head driver for fear of damaging them, then having to drill them out, etc. Before I take everything apart (again) does anybody have any thoughts on the best way to remove the screws, assuming a big screw driver doesn't work? 2 words: impact driver http://www.kk.org/cooltools/archives/000723.php Absolutely. Just had to do this on my son's Kia. Took about 5 seconds to conclude that a normal phillips was completely useless. Then I remembered that when my FIL died several years ago one thing I inherited was a hand impact driver. Murphy's law was not enforced that day so I actually found the darn thing (having never used it prior to that) and it took three blows on one screw and only one on the other. Had a hell of a time getting the second screw separated from the drive head though. While on the topic, WHAT are the engineers thinking in this application? Wouldn't a torx, square drive, or just about anything be better suited to such an application compared to a phillips head? |
OT - Phillips Head Screws On Brake Rotors
Rick Brandt wrote:
On Fri, 07 Aug 2009 11:53:15 -0700, Eric in North TX wrote: On Aug 7, 1:45 pm, DerbyDad03 wrote: The recent thread about impact wrenches got me thinking... I need to change the rotors on my Honda Oddessy. They have 2 large phillips head screws countersunk into the rotors which have to be removed before the rotors will come off. I don't know if they are the original rotors (70K on the van, I've had it since 40K with the same rotors) but I'm thinking that with all the heat generated by braking, they might not be the easiest screws to remove. I didn't want to try backing out the screws with a huge phillips head driver for fear of damaging them, then having to drill them out, etc. Before I take everything apart (again) does anybody have any thoughts on the best way to remove the screws, assuming a big screw driver doesn't work? 2 words: impact driver http://www.kk.org/cooltools/archives/000723.php Absolutely. Just had to do this on my son's Kia. Took about 5 seconds to conclude that a normal phillips was completely useless. Then I remembered that when my FIL died several years ago one thing I inherited was a hand impact driver. Murphy's law was not enforced that day so I actually found the darn thing (having never used it prior to that) and it took three blows on one screw and only one on the other. Had a hell of a time getting the second screw separated from the drive head though. While on the topic, WHAT are the engineers thinking in this application? Wouldn't a torx, square drive, or just about anything be better suited to such an application compared to a phillips head? I'm not sure why they're even required. One would think a simple indexing pin would suffice. nate -- replace "roosters" with "cox" to reply. http://members.cox.net/njnagel |
OT - Phillips Head Screws On Brake Rotors
"Eric in North TX" wrote in message ... On Aug 7, 1:45 pm, DerbyDad03 wrote: The recent thread about impact wrenches got me thinking... I need to change the rotors on my Honda Oddessy. They have 2 large phillips head screws countersunk into the rotors which have to be removed before the rotors will come off. I don't know if they are the original rotors (70K on the van, I've had it since 40K with the same rotors) but I'm thinking that with all the heat generated by braking, they might not be the easiest screws to remove. I didn't want to try backing out the screws with a huge phillips head driver for fear of damaging them, then having to drill them out, etc. Before I take everything apart (again) does anybody have any thoughts on the best way to remove the screws, assuming a big screw driver doesn't work? 2 words: impact driver http://www.kk.org/cooltools/archives/000723.php Yes, that's what I used to use on my Honda 90. |
OT - Phillips Head Screws On Brake Rotors
On Aug 7, 7:23*pm, Nate Nagel wrote:
Rick Brandt wrote: On Fri, 07 Aug 2009 11:53:15 -0700, Eric in North TX wrote: On Aug 7, 1:45 pm, DerbyDad03 wrote: The recent thread about impact wrenches got me thinking... I need to change the rotors on my Honda Oddessy. They have *2 large phillips head screws countersunk into the rotors which have to be removed before the rotors will come off. I don't know if they are the original rotors (70K on the van, I've had it since 40K with the same rotors) but I'm thinking that with all the heat generated by braking, they might not be the easiest screws to remove. I didn't want to try backing out the screws with a huge phillips head driver for fear of damaging them, then having to drill them out, etc. Before I take everything apart (again) does anybody have any thoughts on the best way to remove the screws, assuming a big screw driver doesn't work? 2 words: impact driver http://www.kk.org/cooltools/archives/000723.php Absolutely. *Just had to do this on my son's Kia. *Took about 5 seconds to conclude that a normal phillips was completely useless. *Then I remembered that when my FIL died several years ago one thing I inherited was a hand impact driver. * Murphy's law was not enforced that day so I actually found the darn thing (having never used it prior to that) and it took three blows on one screw and only one on the other. *Had a hell of a time getting the second screw separated from the drive head though. While on the topic, WHAT are the engineers thinking in this application? * Wouldn't a torx, square drive, or just about anything be better suited to such an application compared to a phillips head? I'm not sure why they're even required. *One would think a simple indexing pin would suffice. nate -- replace "roosters" with "cox" to reply.http://members.cox.net/njnagel "One would think a simple indexing pin would suffice. Or *nothing* like just about every other car I've done brakes on. My son's Mitsubishi Gallant not only has nothing holding his rotors on, but they even provide 2 threaded holes so you can drive bolts into the rotor and force it off the hub if it gets stuck. |
OT - Phillips Head Screws On Brake Rotors
DerbyDad03 wrote:
On Aug 7, 7:23 pm, Nate Nagel wrote: Rick Brandt wrote: On Fri, 07 Aug 2009 11:53:15 -0700, Eric in North TX wrote: On Aug 7, 1:45 pm, DerbyDad03 wrote: The recent thread about impact wrenches got me thinking... I need to change the rotors on my Honda Oddessy. They have 2 large phillips head screws countersunk into the rotors which have to be removed before the rotors will come off. I don't know if they are the original rotors (70K on the van, I've had it since 40K with the same rotors) but I'm thinking that with all the heat generated by braking, they might not be the easiest screws to remove. I didn't want to try backing out the screws with a huge phillips head driver for fear of damaging them, then having to drill them out, etc. Before I take everything apart (again) does anybody have any thoughts on the best way to remove the screws, assuming a big screw driver doesn't work? 2 words: impact driver http://www.kk.org/cooltools/archives/000723.php Absolutely. Just had to do this on my son's Kia. Took about 5 seconds to conclude that a normal phillips was completely useless. Then I remembered that when my FIL died several years ago one thing I inherited was a hand impact driver. Murphy's law was not enforced that day so I actually found the darn thing (having never used it prior to that) and it took three blows on one screw and only one on the other. Had a hell of a time getting the second screw separated from the drive head though. While on the topic, WHAT are the engineers thinking in this application? Wouldn't a torx, square drive, or just about anything be better suited to such an application compared to a phillips head? I'm not sure why they're even required. One would think a simple indexing pin would suffice. nate -- replace "roosters" with "cox" to reply.http://members.cox.net/njnagel "One would think a simple indexing pin would suffice. Or *nothing* like just about every other car I've done brakes on. My son's Mitsubishi Gallant not only has nothing holding his rotors on, but they even provide 2 threaded holes so you can drive bolts into the rotor and force it off the hub if it gets stuck. A lot of German cars use the screws. I was told that it was to locate the rotor more precisely than can be done by the lug studs, FWIW. It's also helpful on cars that use lug bolts instead of lug studs (BMW, VW) so you don't have to try to line up the wheel, rotor AND hub at the side of the road after you've gotten a flat (on the non-drive end of the car, of course, so it's all flailing around under there.) But as I said, I don't see why a simple pin pressed into the hub to mate with a hole in the rotor wouldn't accomplish the same thing... nate -- replace "roosters" with "cox" to reply. http://members.cox.net/njnagel |
OT - Phillips Head Screws On Brake Rotors
Now, that's thoughtful. I had a van, the back drums didn't
want to come off. I finally jacked it up, put in reverse, and used a grinder and drill to take the center part down a tiny bit. -- Christopher A. Young Learn more about Jesus www.lds.org .. "DerbyDad03" wrote in message ... My son's Mitsubishi Gallant not only has nothing holding his rotors on, but they even provide 2 threaded holes so you can drive bolts into the rotor and force it off the hub if it gets stuck. |
OT - Phillips Head Screws On Brake Rotors
Don't even try a screwdriver. Go buy a $10 impact driver. It will take
them right out with no damage. Steve "DerbyDad03" wrote in message ... The recent thread about impact wrenches got me thinking... I need to change the rotors on my Honda Oddessy. They have 2 large phillips head screws countersunk into the rotors which have to be removed before the rotors will come off. I don't know if they are the original rotors (70K on the van, I've had it since 40K with the same rotors) but I'm thinking that with all the heat generated by braking, they might not be the easiest screws to remove. I didn't want to try backing out the screws with a huge phillips head driver for fear of damaging them, then having to drill them out, etc. Before I take everything apart (again) does anybody have any thoughts on the best way to remove the screws, assuming a big screw driver doesn't work? |
OT - Phillips Head Screws On Brake Rotors
"Stormin Mormon" wrote in news:h5ikmu
: Now, that's thoughtful. I had a van, the back drums didn't want to come off. I finally jacked it up, put in reverse, and used a grinder and drill to take the center part down a tiny bit. Had a pickup with that issue. Bud was a pro fleet mechanic and I took it by his shop. I had already soaked the hub with Break Away with my efforts. He jacked it up, gave em a couple of good whacks with a hand sledge and they came right off. I would have feared cracking or distorting them. He says nope. Never had any issues with them afterwards. |
OT - Phillips Head Screws On Brake Rotors
"DerbyDad03" wrote in message ... The recent thread about impact wrenches got me thinking... I need to change the rotors on my Honda Oddessy. They have 2 large phillips head screws countersunk into the rotors which have to be removed before the rotors will come off. I don't know if they are the original rotors (70K on the van, I've had it since 40K with the same rotors) but I'm thinking that with all the heat generated by braking, they might not be the easiest screws to remove. I didn't want to try backing out the screws with a huge phillips head driver for fear of damaging them, then having to drill them out, etc. Before I take everything apart (again) does anybody have any thoughts on the best way to remove the screws, assuming a big screw driver doesn't work? When I'm in doubt, (ha, always) I use a hammer and the right sized screwdriver to give the screw a whack or two, helps frac any rust, then soak in penetrating oil. Coke works also. |
OT - Phillips Head Screws On Brake Rotors
Oren wrote:
On Fri, 7 Aug 2009 13:57:23 -0700 (PDT), DerbyDad03 wrote: On Aug 7, 2:53 pm, Eric in North TX wrote: On Aug 7, 1:45 pm, DerbyDad03 wrote: The recent thread about impact wrenches got me thinking... I need to change the rotors on my Honda Oddessy. They have 2 large phillips head screws countersunk into the rotors which have to be removed before the rotors will come off. I don't know if they are the original rotors (70K on the van, I've had it since 40K with the same rotors) but I'm thinking that with all the heat generated by braking, they might not be the easiest screws to remove. I didn't want to try backing out the screws with a huge phillips head driver for fear of damaging them, then having to drill them out, etc. Before I take everything apart (again) does anybody have any thoughts on the best way to remove the screws, assuming a big screw driver doesn't work? 2 words: impact driverhttp://www.kk.org/cooltools/archives/000723.php I'll look into it, but... From the website... "although it takes some skill to keep it on the bolt when you hammer it." And they seem to be talking about a socket over a bolt, not a bit in a phillips head screw. It's hard to tell the size of the screwdriver bolts from the pictures, but none of them look big enough to fit securely in the large philips head screws on my rotor. I'll stop by Sears and see what they look like close up. Thanks! My wrench came from Sears many years ago. "6 pc. impact driver set lets you free frozen or rusted screws. Each hammer blow develops 200 ft. lb. of torque. Includes 1/2 in. sq. drive tool, bit holder, 3/8 in. slotted and Nos. 2, 3 and 4 Phillips bits." Same as this pic: http://www.toolnet.co.za/images/47641.jpg Mine is 40 years old. Indispensable when you need it. I bought it for working on my motorcycle. It eliminated stripped philip heads. |
OT - Phillips Head Screws On Brake Rotors
Bob F wrote:
Oren wrote: On Fri, 7 Aug 2009 13:57:23 -0700 (PDT), DerbyDad03 wrote: On Aug 7, 2:53 pm, Eric in North TX wrote: On Aug 7, 1:45 pm, DerbyDad03 wrote: The recent thread about impact wrenches got me thinking... I need to change the rotors on my Honda Oddessy. They have 2 large phillips head screws countersunk into the rotors which have to be removed before the rotors will come off. I don't know if they are the original rotors (70K on the van, I've had it since 40K with the same rotors) but I'm thinking that with all the heat generated by braking, they might not be the easiest screws to remove. I didn't want to try backing out the screws with a huge phillips head driver for fear of damaging them, then having to drill them out, etc. Before I take everything apart (again) does anybody have any thoughts on the best way to remove the screws, assuming a big screw driver doesn't work? 2 words: impact driverhttp://www.kk.org/cooltools/archives/000723.php I'll look into it, but... From the website... "although it takes some skill to keep it on the bolt when you hammer it." And they seem to be talking about a socket over a bolt, not a bit in a phillips head screw. It's hard to tell the size of the screwdriver bolts from the pictures, but none of them look big enough to fit securely in the large philips head screws on my rotor. I'll stop by Sears and see what they look like close up. Thanks! My wrench came from Sears many years ago. "6 pc. impact driver set lets you free frozen or rusted screws. Each hammer blow develops 200 ft. lb. of torque. Includes 1/2 in. sq. drive tool, bit holder, 3/8 in. slotted and Nos. 2, 3 and 4 Phillips bits." Same as this pic: http://www.toolnet.co.za/images/47641.jpg Mine is 40 years old. Indispensable when you need it. I bought it for working on my motorcycle. It eliminated stripped philip heads. I could add - the trick of it is that it applies huge force inward on the bit at the same time as it turns hard, thus making sure the bit doesn't slip out of the head, and unloading the screw threads at the same time. |
OT - Phillips Head Screws On Brake Rotors
I got something like that, many years ago. Never had any
luck with it. Might end up buying another one, and see if my technique has improved. -- Christopher A. Young Learn more about Jesus www.lds.org .. "Bob F" wrote in message ... My wrench came from Sears many years ago. "6 pc. impact driver set lets you free frozen or rusted screws. Each hammer blow develops 200 ft. lb. of torque. Includes 1/2 in. sq. drive tool, bit holder, 3/8 in. slotted and Nos. 2, 3 and 4 Phillips bits." Same as this pic: http://www.toolnet.co.za/images/47641.jpg Mine is 40 years old. Indispensable when you need it. I bought it for working on my motorcycle. It eliminated stripped philip heads. |
OT - Phillips Head Screws On Brake Rotors
DerbyDad03 wrote:
The recent thread about impact wrenches got me thinking... I need to change the rotors on my Honda Oddessy. They have 2 large phillips head screws countersunk into the rotors which have to be removed before the rotors will come off. I don't know if they are the original rotors (70K on the van, I've had it since 40K with the same rotors) but I'm thinking that with all the heat generated by braking, they might not be the easiest screws to remove. I didn't want to try backing out the screws with a huge phillips head driver for fear of damaging them, then having to drill them out, etc. Before I take everything apart (again) does anybody have any thoughts on the best way to remove the screws, assuming a big screw driver doesn't work? I second the suggestion for the impact driver in the first reply. That is if they don't come out easy. You might be surprised. You can also '86 those screws after you get them out. s |
OT - Phillips Head Screws On Brake Rotors
On Sun, 09 Aug 2009 09:56:13 -0500, Steve Barker
wrote: DerbyDad03 wrote: The recent thread about impact wrenches got me thinking... I need to change the rotors on my Honda Oddessy. They have 2 large phillips head screws countersunk into the rotors which have to be removed before the rotors will come off. I don't know if they are the original rotors (70K on the van, I've had it since 40K with the same rotors) but I'm thinking that with all the heat generated by braking, they might not be the easiest screws to remove. I didn't want to try backing out the screws with a huge phillips head driver for fear of damaging them, then having to drill them out, etc. Before I take everything apart (again) does anybody have any thoughts on the best way to remove the screws, assuming a big screw driver doesn't work? I second the suggestion for the impact driver in the first reply. That is if they don't come out easy. You might be surprised. You can also '86 those screws after you get them out. s Yes, they are ONLY there to hold the rotors/drums on while moving down the assembly line and serve no real purpose when the vehicle is in operation. |
OT - Phillips Head Screws On Brake Rotors
|
OT - Phillips Head Screws On Brake Rotors
On Aug 7, 2:45*pm, DerbyDad03 wrote:
The recent thread about impact wrenches got me thinking... I need to change the rotors on my Honda Oddessy. They have *2 large phillips head screws countersunk into the rotors which have to be removed before the rotors will come off. I don't know if they are the original rotors (70K on the van, I've had it since 40K with the same rotors) but I'm thinking that with all the heat generated by braking, they might not be the easiest screws to remove. I didn't want to try backing out the screws with a huge phillips head driver for fear of damaging them, then having to drill them out, etc. Before I take everything apart (again) does anybody have any thoughts on the best way to remove the screws, assuming a big screw driver doesn't work? Update: I went to a nearby franchise of Cole Muffler who I have used many, many times in the past. I know the manager - his kids play in a sports leauge that I help run. He charged me $24 more to install 4 rotors than I could have bought them for at AutoZone. That's $6 per wheel...and that was after he knew that I had already changed the pads so he knew he wasn't getting that business. It's not worth getting dirty for $24! |
OT - Phillips Head Screws On Brake Rotors
brudot had written this in response to
http://www.thestuccocompany.com/main...rs-387731-.htm : I just changed rotors on my daughter's 2004 Honda Oddessy today. I used a hand held impact driver to remove the all but two screws. Two would not loosen and the heads were starting to strip and the driver bit was distorting. I applied heat to the heads until cherry red (happened quickly with welding torch) and they came out with little difficulty. |
OT - Phillips Head Screws On Brake Rotors
brudot wrote:
I appologize if this is a duplicate post, I'm new. You're also SPAMMING this group SPAM from the sucko company. They do not run this forum, they leach off of the content, put it on their webpage, and SPAM their business name on posts from people too naive to know the difference. Many people in this group explicitly ****can anything with the sucko company on it. My advice is for you to figure out what usenet is, get a newsreader (even Outlook Express), and become part of the community. Even posting from GoogleGroups is a hundred times better than helping the sucko company SPAM this group. Jon |
OT - Phillips Head Screws On Brake Rotors
On Thu, 22 Oct 2009 14:28:17 -0700, "Jon Danniken"
wrote: brudot wrote: I appologize if this is a duplicate post, I'm new. You're also SPAMMING this group SPAM from the sucko company. They do not run this forum, they leach off of the content, put it on their webpage, and SPAM their business name on posts from people too naive to know the difference. If they don't know the difference, I don't think he can be spamming, which requires intention. I think you're awfully hard on this guy, whose post was quite interesting. (I would have used a propane torch and it wouldn't have gotten so hot so fast. OTOH, I don't have a welding torch. :) ) The only advertising was their name in the url, one line. I know plenty of people with a longer sig than that. And loads of newsgroups are quoted on the web. This one is in real time it seems, at least some of the time. So they can, afaik, really participate. To Brudot, it is a lot easier and better in many ways (no advertising, full screen text, more control, much much easier to refer to prior posts, ability to cross post to mulitple ngs when appropriate) to read newsgroups with a newsreader, like Agent of Thunderbird, etc. and there are afaict NO advantages to reading on the web. You should learn about it. But afaic, you're welcome to read the way you are. Remove nopsam to write me. |
| All times are GMT +1. The time now is 03:53 AM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter