shed dimension
Here is a silly question. I am planning on building a 12'x16' shed
with 1/2" OSB sheathing. When I build the frame, should the actual dimensions be 12'x16' or should it be 1 inch less in each dimension to account for the 1 inch of OSB? Thanks for the help. |
shed dimension
|
shed dimension
On Fri, 22 May 2009 14:44:20 -0400, Jim Elbrecht
wrote: On Fri, 22 May 2009 11:13:18 -0700 (PDT), wrote: Here is a silly question. I am planning on building a 12'x16' shed with 1/2" OSB sheathing. When I build the frame, should the actual dimensions be 12'x16' or should it be 1 inch less in each dimension to account for the 1 inch of OSB? Thanks for the help. What do your blueprints say?g Keep in mind that when you go to sheath the roof life is easier if you can use full sheets or trim them slightly. Sheathing a roof that is 8'4" x 16' 6" is a royal PITA. I'm sure there are plans online that will eliminate a lot of re-doing as you work. Jim And in MOST places, a shed that size requires a permit. 100 sq ft is the maximum without a permit around here. |
shed dimension
On May 22, 2:53*pm, wrote:
On Fri, 22 May 2009 14:44:20 -0400, Jim Elbrecht wrote: On Fri, 22 May 2009 11:13:18 -0700 (PDT), wrote: Here is a silly question. *I am planning on building a 12'x16' shed with 1/2" OSB sheathing. *When I build the frame, should the actual dimensions be 12'x16' or should it be 1 inch less in each dimension to account for the 1 inch of OSB? *Thanks for the help. What do your blueprints say?g Keep in mind that when you go to sheath the roof life is easier if you can use full sheets or trim them slightly. * Sheathing a roof that is 8'4" x 16' 6" is a royal PITA. I'm sure there are plans online that will eliminate a lot of re-doing as you work. Jim And in MOST places, a shed that size requires a permit. 100 sq ft is the maximum without a permit around here.- Hide quoted text - - Show quoted text - I do need a permit. That is why the question came up. I am trying to make a drawing to submit to the building inspector. In the past I have done interior framing and always account for the drywall when planning dimensions. So I was unsure if common practice is to make the frame to the stated dimension, or should the dimensions describe the full size with wall sheathing. My original post might have been unclear, but I was referring to sheathing the siding, not the roof. Thanks, Doug |
shed dimension
wrote in message ... BTW if you want a set of engineered plans for a 12 x 16 shed (and a couple other sizes) most Florida building departments have them for free. http://www3.leegov.com/dcd/BuildingS...ShedAppReq.htm So the whole thing is you pay about $ 150 worth of permits for the building. What a money maker. |
shed dimension
Here is a silly question. I am planning on building a 12'x16' shed with 1/2" OSB sheathing. When I build the frame, should the actual dimensions be 12'x16' or should it be 1 inch less in each dimension to account for the 1 inch of OSB? Thanks for the help. You're in luck; this was a topic at last night's Habitat for Humanity volunteer meeting. The measurement is 12 (or 16) feet, outside to outside of the corner studs. Start with the edge of the sheathing even with the edge of the corner stud. Measure over four feet. This is the _center_ of a stud. Now measure over eight feet. That, again, is the _center_ of a stud. The tendency is to put the _edge_ of a stud at the 4- and 8-foot marks, because, after all, the studs go every 16 or 24 inches, right? If you do that, you wind up with the edge of the sheathing floating right *next to* the stud. The important studs are the ones at 4- and 8-foot intervals. All the rest just need to be spaced at 16 inches, more or less. Note: The sheathing will not form a butt joint at the wall corners. That's OK--it'll all be covered by siding and trim. -- Steve Bell New Life Home Improvement Arlington, TX USA |
shed dimension
wrote:
On Fri, 22 May 2009 17:18:39 -0500, "Ralph Mowery" wrote: wrote in message ... BTW if you want a set of engineered plans for a 12 x 16 shed (and a couple other sizes) most Florida building departments have them for free. http://www3.leegov.com/dcd/BuildingS...ShedAppReq.htm So the whole thing is you pay about $ 150 worth of permits for the building. What a money maker. There is so much bureaucracy in the process I doubt they actually make a dime. hey, the people in the permit office have to eat, too. -- aem sends... |
All times are GMT +1. The time now is 04:07 AM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter