Electricity problem
Hi, I have a question about a problem I have encountered. All the
receptacles in 2 of my upper bedrooms stopped working, after I checked the breaker had tripped in the main fuse box. It worked a few times after I turned the fuse back on but now tonight I cannot get the fuse to work (keeps tripping). When I checked my ensuite the Ground Fault Protector (maybe called something else) is not working, when I press "test" the "reset" button does not come out so that I can in fact reset it. Would this cause all the outlets on that circuit not to work or just the outlet by the sink? If it is all of the outlets is this Ground Fault Protector easy to change? Thanks in advance. Mike |
Electricity problem
On Jan 10, 8:52�pm, "Realist" wrote:
Hi, I have a question about a problem I have encountered. All the receptacles in 2 of my upper bedrooms stopped working, after I checked the breaker had tripped in the main fuse box. It worked a few times after I turned the fuse back on but now tonight I cannot get the fuse to work (keeps tripping). When I checked my ensuite the Ground Fault Protector (maybe called something else) is not working, when I press "test" the "reset" button does not come out so that I can in fact reset it. Would this cause all the outlets on that circuit not to work or just the outlet by the sink? If it is all of the outlets is this Ground Fault Protector easy to change? Thanks in advance. Mike If the GFI is on the dead circuit the one with the tripped breaker you will NOT be able to reset it. Go around check EVERY OUTLET in your home and unplug everything thats plugged into a dead outlet, then try restetting breaker something plugged in like a lamp is likely shorted |
Electricity problem
"Realist" wrote in message ... Hi, I have a question about a problem I have encountered. All the receptacles in 2 of my upper bedrooms stopped working, after I checked the breaker had tripped in the main fuse box. It worked a few times after I turned the fuse back on but now tonight I cannot get the fuse to work (keeps tripping). When I checked my ensuite the Ground Fault Protector (maybe called something else) is not working, when I press "test" the "reset" button does not come out so that I can in fact reset it. Would this cause all the outlets on that circuit not to work or just the outlet by the sink? If it is all of the outlets is this Ground Fault Protector easy to change? Thanks in advance. Mike It sounds like two separate issues. If a circuit breaker trips when you reset it, there is a short circuit on that line. It could be in the wiring or it could be something plugged into an outlet on the circuit. I would first try turning off any lights on that circuit, and unplugging anything in the outlets, then try resetting the breaker. The GFCI breaker must be pushed to the full off position before trying to reset it. If it trips when reset, there is either a ground fault or short circuit on that line. If it just won't switch on , it may be a defective breaker |
Electricity problem
Thank you!!!
This all happened after I moved my TV from one outlet to another, I mounted it on my wall. Before the move I had 2 satellite receivers, 1 DVD player a security system, a Laptop as well as the TV into one outlet, this one is empty now. Nothing new has been added, the only change is that the TV has been moved and it is going into an outlet that we have not used before and we use a small extension cord to connect it. The breaker worked for about 10 minutes later tonight and I tried the GFI test, it did not work while the power was going to the outlets. |
Electricity problem
On Sat, 10 Jan 2009 22:48:43 -0500, "RBM" wrote:
"Realist" wrote in message .. . Hi, I have a question about a problem I have encountered. All the receptacles in 2 of my upper bedrooms stopped working, after I checked the breaker had tripped in the main fuse box. It worked a few times after I turned the fuse back on but now tonight I cannot get the fuse to work (keeps tripping). When I checked my ensuite the Ground Fault Protector (maybe called something else) is not working, when I press "test" the "reset" button does not come out so that I can in fact reset it. Would this cause all the outlets on that circuit not to work or just the outlet by the sink? If it is all of the outlets is this Ground Fault Protector easy to change? Thanks in advance. Mike It sounds like two separate issues. If a circuit breaker trips when you reset it, there is a short circuit on that line. It could be in the wiring or it could be something plugged into an outlet on the circuit. I would first try turning off any lights on that circuit, and unplugging anything in the outlets, then try resetting the breaker. The GFCI breaker must be pushed to the full off position before trying to reset it. If it trips when reset, there is either a ground fault or short circuit on that line. If it just won't switch on , it may be a defective breaker You didn't put a screw into a wire when you mounted the TV on the wall, did you? That would cause the problem you are having and would explain why it is happening NOW, and not before moving the TV |
Electricity problem
I can't say for sure if that happened or not. I thought about that. There as
an outlet below the mounted TV and three feet to the left so I assumed the wiring would have been along that height. The outlets worked for a day or so after the first trip, would they work if I in fact screwed into a wire? |
Electricity problem
Forgot to mention that the mount is 5 inches from the ceiling.
|
Electricity problem
Realist wrote: Forgot to mention that the mount is 5 inches from the ceiling. Andy comments: Usually the wiring is run thru the attic to the room, where it goes DOWN the side of a stud. Then, it is often carried to the other room outlets at the outlet height, around 15 inches or so from the floor. Windows and doors mean going back up a stud.... So, you "might" have hit the wire rwhere it runs up or down a stud. Statistically, it is very rare,.... but it is possible. Good luck. |
Electricity problem
"Realist" wrote in message ... I can't say for sure if that happened or not. I thought about that. There as an outlet below the mounted TV and three feet to the left so I assumed the wiring would have been along that height. The outlets worked for a day or so after the first trip, would they work if I in fact screwed into a wire? That depends upon what you hit inside the cable. You may have just grazed two of the conductors, so it could trip intermittently |
Electricity problem
I unplugged everything from all outlets on this circuit and turned the
breaker on this morning. It has been 2 1/2 hours now and it has not tripped. Would it trip anyway if I were screwed into a wire? We'll see, if it happens again I'll call an electrician. Thanks |
Electricity problem
I just went into the attic and had a look, there are no wires going into the
ceiling on that stud, but that GFI in the washroom still does not work. The outlet in that same washroom worked while the breaker was off though, must be on another breaker. |
Electricity problem
On Jan 11, 9:01�am, "Realist" wrote:
I unplugged everything from all outlets on this circuit and turned the breaker on this morning. It has been 2 1/2 hours now and it has not tripped. Would it trip anyway if I were screwed into a wire? We'll see, if it happens again I'll call an electrician. Thanks take each item you unplugged and plug into a different circuit. sounds like you ran your new mount into a wire in wall. bad things happen:( |
Electricity problem
"Realist" wrote in message ... I unplugged everything from all outlets on this circuit and turned the breaker on this morning. It has been 2 1/2 hours now and it has not tripped. Would it trip anyway if I were screwed into a wire? We'll see, if it happens again I'll call an electrician. Thanks If the breaker trips with things plugged in, and doesn't trip with things NOT plugged in, the problem is obviously with one of the things you had plugged in and not the wiring or the TV mount. |
Electricity problem
On Jan 11, 11:51�am, "RBM" wrote:
"Realist" wrote in message ... I unplugged everything from all outlets on this circuit and turned the breaker on this morning. It has been 2 1/2 hours now and it has not tripped. Would it trip anyway if I were screwed into a wire? We'll see, if it happens again I'll call an electrician. Thanks If the breaker trips with things plugged in, and doesn't trip with things NOT plugged in, the problem is obviously with one of the things you had plugged in and not the wiring or the TV mount. PROBABLY! A low level short might only trip when any other load is added. I would feel the wall where the new mount is screwed in for warmth. |
Electricity problem
On Sun, 11 Jan 2009 08:02:07 -0330, "Realist"
wrote: I can't say for sure if that happened or not. I thought about that. There as an outlet below the mounted TV and three feet to the left so I assumed the wiring would have been along that height. The outlets worked for a day or so after the first trip, would they work if I in fact screwed into a wire? They could. Depends on how badly you nipped the wire. I'd back out the screws and see what happens (one at a time) and if one is causing the problem I'd open the wall and repair it. The patch will be behind the TV so if it doesn't match 100% it will be fine untill the room needs repainting again. |
Electricity problem
On Sun, 11 Jan 2009 07:27:29 -0800 (PST), "
wrote: On Jan 11, 9:01?am, "Realist" wrote: I unplugged everything from all outlets on this circuit and turned the breaker on this morning. It has been 2 1/2 hours now and it has not tripped. Would it trip anyway if I were screwed into a wire? We'll see, if it happens again I'll call an electrician. Thanks take each item you unplugged and plug into a different circuit. sounds like you ran your new mount into a wire in wall. bad things happen:( Plug in the TV first and see what happens. The TV is grounded (in all likelihood) so if you nipped the wire plugging in the TV COULD trip either the GFI or the breaker. |
Electricity problem
wrote in message ... On Jan 11, 11:51?am, "RBM" wrote: "Realist" wrote in message ... I unplugged everything from all outlets on this circuit and turned the breaker on this morning. It has been 2 1/2 hours now and it has not tripped. Would it trip anyway if I were screwed into a wire? We'll see, if it happens again I'll call an electrician. Thanks If the breaker trips with things plugged in, and doesn't trip with things NOT plugged in, the problem is obviously with one of the things you had plugged in and not the wiring or the TV mount. PROBABLY! A low level short might only trip when any other load is added. I would feel the wall where the new mount is screwed in for warmth. Nonsense |
Electricity problem
I cut a hole in the wall to see if I in fact hit a wire when mounting the TV
and I didn't hit one. Now I am really stumped. On a bright note now I will put an outlet where I cut the hole. LOL |
Electricity problem
In article ,
"Realist" wrote: I cut a hole in the wall to see if I in fact hit a wire when mounting the TV and I didn't hit one. Now I am really stumped. On a bright note now I will put an outlet where I cut the hole. LOL What the hell are you stumped about? It's been 'splained to you in simple terms: something that you did have plugged into one of the outlets on the circuit has a short, or is drawing excess current for some reason. It would take you two minutes to isolate the faulty device. |
All times are GMT +1. The time now is 08:11 AM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter