Air compressor
 

-------------------------------------

I am putting in a new Rockworth air compressor. I have ran a 10/3
underground wire for power(30'). The motor is 5 HP running. I need a cord
to plug the motor in with. Should I use a 10 ga.or will 12 work for this.
I know where I was working at we ran 12 ga. wire (200')to a 1 hp motor
with 12 ga. plug 220 volts.


##-----------------------------------------------##
Delivered via http://www.thestuccocompany.com/
Building Construction and Maintenance Forum
Web and RSS access to your favorite newsgroup -
alt.home.repair - 329535 messages and counting!
##-----------------------------------------------##

Air compressor
 

HB wrote:

-------------------------------------

I am putting in a new Rockworth air compressor. I have ran a 10/3
underground wire for power(30'). The motor is 5 HP running. I need a cord
to plug the motor in with. Should I use a 10 ga.or will 12 work for this.
I know where I was working at we ran 12 ga. wire (200')to a 1 hp motor
with 12 ga. plug 220 volts.



220 volts, right? Then twelve will be fine. (assumes reasonable length
cord.) It's not easy finding a 20A plug that will accept #10 cord.

Bob

Air compressor
 

On Dec 14, 2:09*pm, zxcvbob wrote:
HB wrote:

-------------------------------------

I am putting in a new Rockworth air compressor. I have ran a 10/3
underground wire for power(30'). The motor is 5 HP running. I need a cord
to plug the motor in with. Should I use a 10 ga.or will 12 work for this.
I know where I was working at we ran 12 ga. wire (200')to a 1 hp motor
with 12 ga. plug 220 volts.

220 volts, right? *Then twelve will be fine. (assumes reasonable length
cord.) *It's not easy finding a 20A plug that will accept #10 cord.

Bob

If you get a NEMA 6-30R receptacle and 6-30P plug you won't have to
fight with it. If using stranded wire consider getting some crimp
fittings to make it easier. Easy to find at any place the pros hang
out.

Joe

Air compressor
 

On 14 Dec 2008 20:03:17 GMT,
(HB) wrote:



-------------------------------------

I am putting in a new Rockworth air compressor. I have ran a 10/3
underground wire for power(30'). The motor is 5 HP running. I need a cord
to plug the motor in with. Should I use a 10 ga.or will 12 work for this.
I know where I was working at we ran 12 ga. wire (200')to a 1 hp motor
with 12 ga. plug 220 volts.



That's a hefty motor. Use 10 ga for 120 volts, 12 ga for 220v.

Air compressor
 

On Dec 14, 2:03*pm, (HB) wrote:
-------------------------------------

I am putting in a new Rockworth air compressor. I have ran a 10/3
underground wire for power(30'). The motor is 5 HP running. I need a cord
to plug the motor in with. Should I use a 10 ga.or will 12 work for this.
I know where I was working at we ran 12 ga. wire (200')to a 1 hp motor
with 12 ga. plug 220 volts.

##-----------------------------------------------##
Delivered via *http://www.thestuccocompany.com/
Building Construction and Maintenance Forum
Web and RSS access to your favorite newsgroup -
alt.home.repair - 329535 messages and counting!
##-----------------------------------------------##

Rockworth, is that a chinese company trying to mimic the famed
Rockwell co.

Air compressor
 

Hb had written this in response to
http://www.thestuccocompany.com/main...or-348213-.htm
:
It is from the UK as best i can tell. They have a website. There is a
distributer in Rock Hill.SC. As far as the cord I am only going 4' to the
plud that is coming from the breaker with the 10/3 solid wire. It does not
have the cord to plug into the wall. so12/3 should be fine. Te weird part
is they do not have this one listed on their website. RW7580V2 80 gallon

-------------------------------------
ransley wrote:

On Dec 14, 2:03=A0pm, (HB) wrote:
-------------------------------------

I am putting in a new Rockworth air compressor. I have ran a 10/3
underground wire for power(30'). The motor is 5 HP running. I need
a cord
to plug the motor in with. Should I use a 10 ga.or will 12 work
for this.
I know where I was working at we ran 12 ga. wire (200')to a 1 hp
motor
with 12 ga. plug 220 volts.

##-----------------------------------------------##
Delivered via =A0http://www.thestuccocompany.com/
Building Construction and Maintenance Forum
Web and RSS access to your favorite newsgroup -
alt.home.repair - 329535 messages and counting!
##-----------------------------------------------##

Rockworth, is that a chinese company trying to mimic the famed
Rockwell co.





##-----------------------------------------------##
Delivered via http://www.thestuccocompany.com/
Building Construction and Maintenance Forum
Web and RSS access to your favorite newsgroup -
alt.home.repair - 329599 messages and counting!
##-----------------------------------------------##

Air compressor
 

Hb had written this in response to
http://www.thestuccocompany.com/main...or-348167-.htm
:

I just looked at the motor again and it says it draws 22 amps. Will this
be a problem with the 12 guage wire from the motor to the receptacle which
is a 250 volt plug -|. With 10/3 into it.
-------------------------------------
zxcvbob wrote:

HB wrote:

-------------------------------------

I am putting in a new Rockworth air compressor. I have ran a 10/3
underground wire for power(30'). The motor is 5 HP running. I need
a cord
to plug the motor in with. Should I use a 10 ga.or will 12 work
for this.
I know where I was working at we ran 12 ga. wire (200')to a 1 hp
motor
with 12 ga. plug 220 volts.



220 volts, right? Then twelve will be fine. (assumes reasonable length

cord.) It's not easy finding a 20A plug that will accept #10 cord.

Bob





##-----------------------------------------------##
Delivered via http://www.thestuccocompany.com/
Building Construction and Maintenance Forum
Web and RSS access to your favorite newsgroup -
alt.home.repair - 329689 messages and counting!
##-----------------------------------------------##

Air compressor
 

Hb wrote:
Hb had written this in response to
http://www.thestuccocompany.com/main...or-348167-.htm
:

I just looked at the motor again and it says it draws 22 amps. Will this
be a problem with the 12 guage wire from the motor to the receptacle which
is a 250 volt plug -|. With 10/3 into it.
-------------------------------------
zxcvbob wrote:

HB wrote:
-------------------------------------

I am putting in a new Rockworth air compressor. I have ran a 10/3
underground wire for power(30'). The motor is 5 HP running. I need
a cord
to plug the motor in with. Should I use a 10 ga.or will 12 work
for this.
I know where I was working at we ran 12 ga. wire (200')to a 1 hp
motor
with 12 ga. plug 220 volts.




According to table 400-5(A), the ampacity of all common types of flexible cords and cable
is 25A for 12 gauge with 2 current-carrying conductors (and the ampacity of the uncommon
types, like HPN, is 30A)

I might be tempted to use a dryer cord and a 10-30R outlet for this application.

What size breaker are you going to use, (20 or 30A) or are you going to use 25A fuses?
That really determines the proper plug configuration.

Bob

Air compressor
 

Hb had written this in response to
http://www.thestuccocompany.com/main...or-348349-.htm
:
30 amp Thanks for all the help. I think i got it.

-------------------------------------
zxcvbob wrote:

Hb wrote:
Hb had written this in response to

http://www.thestuccocompany.com/main...or-348167-.htm

:

I just looked at the motor again and it says it draws 22 amps.
Will this
be a problem with the 12 guage wire from the motor to the
receptacle which
is a 250 volt plug -|. With 10/3 into it.
-------------------------------------
zxcvbob wrote:

HB wrote:
-------------------------------------

I am putting in a new Rockworth air compressor. I have ran
a 10/3
underground wire for power(30'). The motor is 5 HP
running. I need
a cord
to plug the motor in with. Should I use a 10 ga.or will 12
work
for this.
I know where I was working at we ran 12 ga. wire (200')to
a 1 hp
motor
with 12 ga. plug 220 volts.




According to table 400-5(A), the ampacity of all common types of
flexible cords
and cable
is 25A for 12 gauge with 2 current-carrying conductors (and the
ampacity of the
uncommon
types, like HPN, is 30A)

I might be tempted to use a dryer cord and a 10-30R outlet for this
application.

What size breaker are you going to use, (20 or 30A) or are you going to
use 25A
fuses?
That really determines the proper plug configuration.

Bob





##-----------------------------------------------##
Delivered via http://www.thestuccocompany.com/
Building Construction and Maintenance Forum
Web and RSS access to your favorite newsgroup -
alt.home.repair - 329778 messages and counting!
##-----------------------------------------------##