DIYbanter

DIYbanter (https://www.diybanter.com/)
-   Home Repair (https://www.diybanter.com/home-repair/)
-   -   paint problem (https://www.diybanter.com/home-repair/262500-paint-problem.html)

Chris October 12th 08 09:17 PM

paint problem
 
I just finished a painting project on some old plaster that was
patched and restored. It turned out fine. However, there are a few
areas that look like they could have been sanded a little better. The
areas look rough, and if the light hits it right, it really sticks
out. I did two coats. Is there a way to hide the coarse texture? Or,
is that just the way it will look no matter how many coats goes on? I
was thinking of slapping some paint with a brush and work it in, and
then back roll it with a dry roller. The lady of the house says she
can live with it.. it is just that one area is at eye level with I go
up and down the steps and it sort of bothers me..

Kenneth October 12th 08 10:32 PM

paint problem
 
On Sun, 12 Oct 2008 13:17:18 -0700 (PDT), Chris
wrote:

I just finished a painting project on some old plaster that was
patched and restored. It turned out fine. However, there are a few
areas that look like they could have been sanded a little better. The
areas look rough, and if the light hits it right, it really sticks
out. I did two coats. Is there a way to hide the coarse texture? Or,
is that just the way it will look no matter how many coats goes on? I
was thinking of slapping some paint with a brush and work it in, and
then back roll it with a dry roller. The lady of the house says she
can live with it.. it is just that one area is at eye level with I go
up and down the steps and it sort of bothers me..


Howdy,

I would let it dry completely, then sand the area down to
the plaster, and repaint.

All the best,
--
Kenneth

If you email... Please remove the "SPAMLESS."

Edwin Pawlowski October 12th 08 11:06 PM

paint problem
 

"Chris" wrote in message
...
I just finished a painting project on some old plaster that was
patched and restored. It turned out fine. However, there are a few
areas that look like they could have been sanded a little better. The
areas look rough, and if the light hits it right, it really sticks
out. I did two coats. Is there a way to hide the coarse texture? Or,
is that just the way it will look no matter how many coats goes on? I
was thinking of slapping some paint with a brush and work it in, and
then back roll it with a dry roller. The lady of the house says she
can live with it.. it is just that one area is at eye level with I go
up and down the steps and it sort of bothers me..


About 10 or 15 coats will do it. Or just take the time to sand it smooth and
put two coats over it.



SteveBell October 13th 08 04:49 AM

paint problem
 
Chris wrote:

The lady of the house says she can live with it.


Do you really need to know anything more than this?

--
Steve Bell
New Life Home Improvement
Arlington, TX

Phisherman[_2_] October 13th 08 05:37 PM

paint problem
 
On Sun, 12 Oct 2008 13:17:18 -0700 (PDT), Chris
wrote:

I just finished a painting project on some old plaster that was
patched and restored. It turned out fine. However, there are a few
areas that look like they could have been sanded a little better. The
areas look rough, and if the light hits it right, it really sticks
out. I did two coats. Is there a way to hide the coarse texture? Or,
is that just the way it will look no matter how many coats goes on? I
was thinking of slapping some paint with a brush and work it in, and
then back roll it with a dry roller. The lady of the house says she
can live with it.. it is just that one area is at eye level with I go
up and down the steps and it sort of bothers me..


It may need spackling. A nice painter's trick is to hold a lamp/work
light against the wall and view at a low angle. An excellent paint
job starts with a lot of preparation and re-inspections. A gloss
paint needs more fuss.

DerbyDad03 October 13th 08 06:02 PM

paint problem
 
On Oct 12, 4:17*pm, Chris wrote:
I just finished a painting project on some old plaster that was
patched and restored. It turned out fine. However, there are a few
areas that look like they could have been sanded a little better. The
areas look rough, and if the light hits it right, it really sticks
out. I did two coats. Is there a way to hide the coarse texture? Or,
is that just the way it will look no matter how many coats goes on? I
was thinking of slapping some paint with a brush and work it in, and
then back roll it with a dry roller. The lady of the house says she
can live with it.. it is just that one area is at eye level with I go
up and down the steps and it sort of bothers me..


Hang a picture over it. g

[email protected] October 14th 08 04:00 AM

paint problem
 
On Mon, 13 Oct 2008 03:49:00 +0000 (UTC), "SteveBell"
wrote:

Chris wrote:

The lady of the house says she can live with it.


Do you really need to know anything more than this?



The man is a perfectionist and just as I take pride in the work I do,
so does he. If I only installed 95% of the screws back when working on
a car, well you know the rest.


Chris October 14th 08 07:41 PM

paint problem
 
speaking about that-- there was a little area of a corner that I
missed with the second coat, and I can see it from the bottom of the
stairs.. damn.. gotta get out the extention ladder again!


All times are GMT +1. The time now is 06:55 AM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter