CAN DOWNSPOUT ELBOWS BE BENT ???
 

I just picked up a 10 foot length of 2 X 3 downspout, and a couple of "A" & "B"
90 degree elbows. I have to extend one of my downspouts away from the
house to eliminate water coming in under 1 of my garage doors. I need an angle
of about 120 degrees on one of the elbows. Can I sort of "stretch it out from 90
to 120 degrees" or will the elbow distort and kink ??? Many of the elbows on my
house are straighter than 90 degrees, but the only ones I saw in HD were 90's.


Thanks,


RON
================================================== ======
Remove the ZZZ from my E-mail address to send me E-mail.

CAN DOWNSPOUT ELBOWS BE BENT ???
 

Ron in NY wrote:
I just picked up a 10 foot length of 2 X 3 downspout, and a couple of "A" & "B"
90 degree elbows. I have to extend one of my downspouts away from the
house to eliminate water coming in under 1 of my garage doors. I need an angle
of about 120 degrees on one of the elbows. Can I sort of "stretch it out from 90
to 120 degrees" or will the elbow distort and kink ??? Many of the elbows on my
house are straighter than 90 degrees, but the only ones I saw in HD were 90's.

That's kinda' unusual I'd think to not have anything but a full 90--most
use a 90 rather than horizontal for the return to the downspout from a
gutter.

Probably easier to find them than do the work to modify one, though
ime(stimation)...

--

CAN DOWNSPOUT ELBOWS BE BENT ???
 

Ron in NY wrote:
I just picked up a 10 foot length of 2 X 3 downspout, and a couple of "A" & "B"
90 degree elbows. I have to extend one of my downspouts away from the
house to eliminate water coming in under 1 of my garage doors. I need an angle
of about 120 degrees on one of the elbows. Can I sort of "stretch it out from 90
to 120 degrees" or will the elbow distort and kink ??? Many of the elbows on my
house are straighter than 90 degrees, but the only ones I saw in HD were 90's.


Thanks,


RON
================================================== ======
Remove the ZZZ from my E-mail address to send me E-mail.

Try a real hardware store. I needed something similar and the local
hardware store had a selection of elbows. I don't exactly remember but I
think the one I bought was 110 degrees.

CAN DOWNSPOUT ELBOWS BE BENT ???
 

George wrote:

Try a real hardware store. I needed something similar and the local
hardware store had a selection of elbows. I don't exactly remember but I
think the one I bought was 110 degrees.
================================================== ==========
Unfortunately, there are no "real hardware stores" left around here. They all
closed up within the last 5 years.


RON
================================================== ======
Remove the ZZZ from my E-mail address to send me E-mail.

CAN DOWNSPOUT ELBOWS BE BENT ???
 

On Aug 29, 3:27 pm, (Ron in NY) wrote:
I just picked up a 10 foot length of 2 X 3 downspout, and a couple of "A" & "B"
90 degree elbows. I have to extend one of my downspouts away from the
house to eliminate water coming in under 1 of my garage doors. I need an angle
of about 120 degrees on one of the elbows. Can I sort of "stretch it out from 90
to 120 degrees" or will the elbow distort and kink ??? Many of the elbows on my
house are straighter than 90 degrees, but the only ones I saw in HD were 90's.

Thanks,

RON
================================================== ======
Remove the ZZZ from my E-mail address to send me E-mail.

You can use a 2x4 in each side of the elbow to pry it open to whatever
angle you need. It wouldn't hurt to have a helper, and you might
damage the first one you try this on.

The last time I did this, it was on bigger elbows, so you might need
something slightly smaller than a 2 x4 to do this properly. Best of
luck.

JK

CAN DOWNSPOUT ELBOWS BE BENT ???
 

I need an angle of about 120 degrees on one of the elbows.
Can I sort of "stretch it out from 90
to 120 degrees" or will the elbow distort and kink ???

They make a vinyl elbow that if flexable and can be bent to any angle
you need. Try that.

CAN DOWNSPOUT ELBOWS BE BENT ???
 

Ron in NY wrote:
I just picked up a 10 foot length of 2 X 3 downspout, and a couple of "A" & "B"
90 degree elbows. I have to extend one of my downspouts away from the
house to eliminate water coming in under 1 of my garage doors. I need an angle
of about 120 degrees on one of the elbows. Can I sort of "stretch it out from 90
to 120 degrees" or will the elbow distort and kink ??? Many of the elbows on my
house are straighter than 90 degrees, but the only ones I saw in HD were 90's.


Thanks,


RON
================================================== ======
Remove the ZZZ from my E-mail address to send me E-mail.

Would this work? http://www.homedepot.com/SKU #663430 - "Flex Elbow"
(If not, sorry, I don't know anything about gutters, except that I got a
plastic downspout extension at Home Depot, and noticed these sitting
beside them).