Replacing kitchen faucet
We have an el cheapo kitchen faucet that came with the house (6 years
old). It's a stainless steel one piece with a handle to adjust hot/ cold. It also has a plastic sprayer that's very confused. Never worked as it was intended for. Anyway, these days if we lift the handle, it's coming off. Does it mean we have to replace the faucet or can we replace any part within that will fix it? The faucet still works. We have to be careful not to pull it too hard. Since I'm a newbie I want to find out how easy/hard it is to replace a kitchen faucet. We have replaced cartridges in our bath tubs before. Is replacing a kitchen faucet considerably more complicated than replacing a cartridge? Should the old faucet be thrown away in the trash or will any freecycler have any use for it? Sorry for naive questions. Thanks. |
Replacing kitchen faucet
On 27 Jun, 14:12, wrote:
We have an el cheapo kitchen faucet that came with the house (6 years old). It's a stainless steel one piece with a handle to adjust hot/ cold. It also has a plastic sprayer that's very confused. Never worked as it was intended for. Anyway, these days if we lift the handle, it's coming off. Does it mean we have to replace the faucet or can we replace any part within that will fix it? The faucet still works. We have to be careful not to pull it too hard. Since I'm a newbie I want to find out how easy/hard it is to replace a kitchen faucet. We have replaced cartridges in our bath tubs before. Is replacing a kitchen faucet considerably more complicated than replacing a cartridge? Should the old faucet be thrown away in the trash or will any freecycler have any use for it? Sorry for naive questions. Thanks. Not sure what you mean by "lift the handle" but if it's something like the faucet shown he http://www.efaucets.com/images/moen/large/7423-lg.jpg then look for a set screw on the bottom of the handle, like where the red dot in the picture is. If the set screw is still there, try tightening it, perhaps with an allen wrench. If your faucet isn't anything like the one in the picture, find one on the net, post the link and we'll see what we can do. |
Replacing kitchen faucet
On Jun 27, 2:03 pm, DerbyDad03 wrote:
On 27 Jun, 14:12, wrote: We have an el cheapo kitchen faucet that came with the house (6 years old). It's a stainless steel one piece with a handle to adjust hot/ cold. It also has a plastic sprayer that's very confused. Never worked as it was intended for. Anyway, these days if we lift the handle, it's coming off. Does it mean we have to replace the faucet or can we replace any part within that will fix it? The faucet still works. We have to be careful not to pull it too hard. Since I'm a newbie I want to find out how easy/hard it is to replace a kitchen faucet. We have replaced cartridges in our bath tubs before. Is replacing a kitchen faucet considerably more complicated than replacing a cartridge? Should the old faucet be thrown away in the trash or will any freecycler have any use for it? Sorry for naive questions. Thanks. Not sure what you mean by "lift the handle" but if it's something like the faucet shown he http://www.efaucets.com/images/moen/large/7423-lg.jpg then look for a set screw on the bottom of the handle, like where the red dot in the picture is. If the set screw is still there, try tightening it, perhaps with an allen wrench. If your faucet isn't anything like the one in the picture, find one on the net, post the link and we'll see what we can do. OP here. Thanks for your reply. Here's a link for the faucet. http://www.moen.com/buymoen/buyparts...u_refno=308978 |
Replacing kitchen faucet
|
Replacing kitchen faucet
On Jun 27, 5:17?pm, Rick Blaine wrote:
wrote: Since I'm a newbie I want to find out how easy/hard it is to replace a kitchen faucet. Generally, it's pretty easy. A few things to watch out for: - If you do not have shutoff valves under the sink for both hot & cold, you'll need to find the master water shutoff valve for the house. This valve typically does not get used much and can be fragile. - Clearance between the sink and the back wall under the countertop can be tight. This can make getting a wrench up there difficult. - Some faucets require the use of a sleeve type wrench. -- "Tell me what I should do, Annie." "Stay. Here. Forever." - Life On Mars I just finished relacing my bathroom faucet, the trouble with these jobs is access, and having to do so much by feel only mine had a burst bubble in the flexible line and replacing the fixture was easier than just the lines. The hardware that holds everything in place was all rusty, its been in 10 years. I might save the faucet its a delta and never had a problem but today I didnt want to mess around......... |
Replacing kitchen faucet
On Wed, 27 Jun 2007 12:43:48 -0700, Oren wrote:
On Wed, 27 Jun 2007 12:13:37 -0700, wrote: OP here. Thanks for your reply. Here's a link for the faucet. http://www.moen.com/buymoen/buyparts...u_refno=308978 Step 1 on this page has a link for the illustrated parts list. The top cap will lift off. Going by the exploded view there, it looks like it would be about 1000 times easier to repair the faucet than to replace it. The screw is probably lying right there under the cap -- put it in if necessary and tighten it -- and the cap probably comes right off with a non-serrated steak knife. Plug the sink drain first. |
All times are GMT +1. The time now is 06:26 PM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter