Home |
Search |
Today's Posts |
|
Home Repair (alt.home.repair) For all homeowners and DIYers with many experienced tradesmen. Solve your toughest home fix-it problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
|
#1
Posted to alt.home.repair
|
|||
|
|||
Replace sliding doors with bi-fold
I want to remove existing sliding doors (bedroom closet) and replace
with 2 pair of bi-fold. The opening is very wide, so I need to put in a "T" frame, with each pair of bi-folds installed on each side of the "T". There is no set of bi-folds wide enough to cover the 86" opening. Can I just nail the frame onto existing drywall on sides/ceiling, or should drywall be removed to get a more secure fastening? |
#2
Posted to alt.home.repair
|
|||
|
|||
Replace sliding doors with bi-fold
"Pat Coghlan" wrote in message ... I want to remove existing sliding doors (bedroom closet) and replace with 2 pair of bi-fold. The opening is very wide, so I need to put in a "T" frame, with each pair of bi-folds installed on each side of the "T". There is no set of bi-folds wide enough to cover the 86" opening. Can I just nail the frame onto existing drywall on sides/ceiling, or should drywall be removed to get a more secure fastening? If I am not mistaken you will need to reduce the opening to 72" in order to use bifolds. Maybe a 36 and 48 would work. By-pass is so much more friendly. Are you sure you want to do this? I have owned and installed both and would always choose by-pass. Bi-folds work on pivot pins at the top and bottom. No support at the sides is required. |
#3
Posted to alt.home.repair
|
|||
|
|||
Replace sliding doors with bi-fold
"Pat Coghlan" wrote I want to remove existing sliding doors (bedroom closet) and replace with 2 pair of bi-fold. The opening is very wide, so I need to put in a "T" frame, with each pair of bi-folds installed on each side of the "T". There is no set of bi-folds wide enough to cover the 86" opening. Can I just nail the frame onto existing drywall on sides/ceiling, or should drywall be removed to get a more secure fastening? My closet is 90" wide. It has 3 pairs of bi-folds. There is no framing. There is a metal groove (guide?) all along the top. On the bottom, each pair has an L shaped bracket. The doors all meet each other when they are closed. No framework separates them. Clear as mud? nancy |
#4
Posted to alt.home.repair
|
|||
|
|||
Replace sliding doors with bi-fold
Interesting. Never saw that done before. Must be tricky to get
perfectly aligned. It's hard enough keeping just one set of bifolds aligned. Nancy Young wrote: "Pat Coghlan" wrote I want to remove existing sliding doors (bedroom closet) and replace with 2 pair of bi-fold. The opening is very wide, so I need to put in a "T" frame, with each pair of bi-folds installed on each side of the "T". There is no set of bi-folds wide enough to cover the 86" opening. Can I just nail the frame onto existing drywall on sides/ceiling, or should drywall be removed to get a more secure fastening? My closet is 90" wide. It has 3 pairs of bi-folds. There is no framing. There is a metal groove (guide?) all along the top. On the bottom, each pair has an L shaped bracket. The doors all meet each other when they are closed. No framework separates them. Clear as mud? nancy |
#5
Posted to alt.home.repair
|
|||
|
|||
Replace sliding doors with bi-fold
"Pat Coghlan" wrote Nancy Young wrote: My closet is 90" wide. It has 3 pairs of bi-folds. There is no framing. There is a metal groove (guide?) all along the top. On the bottom, each pair has an L shaped bracket. The doors all meet each other when they are closed. No framework separates them. Interesting. Never saw that done before. Must be tricky to get perfectly aligned. It's hard enough keeping just one set of bifolds aligned. Personally, I think it would be far more difficult to try framing them in. The way mine look, it would seem they'd be hung from that metal track at the top and you would then align the L brackets at the bottom. The bracket just keeps them from swaying in and out like curtains, really. nancy |
#6
Posted to alt.home.repair
|
|||
|
|||
Replace sliding doors with bi-fold
Pat Coghlan wrote:
Interesting. Never saw that done before. Must be tricky to get perfectly aligned. It's hard enough keeping just one set of bifolds aligned. No, it isn't hard. Each bifold door section has pivot points at the top and bottom edges near the outside vertical edge. The doors have metal studs that fit into holes in carriers in the top track and on the floor. The carriers are moveable laterally. That means you can move the door sections a bit horizontally and you can tip them off vertical if needed. To line them up, start with one section nearest a wall and align it vertically, leaving enough space next to the wall so it can open. Then set the next section in place, aligning it to the first and leaving enough space between the two so it can open. Repeat with all other sections. You may have to increase the space between sections to avoid a large gap between the last section and the wall. If there is too little space for the last section you either have to get the sections closer together or cut off a little. Once all are to your liking, you lock the moveable carriers in place with the integral bolts. There will always be a space between the outboard doors and the walls as they must rotate to open...that space can be covered with a small board attached to the wall. The next job is to lock the doors into the carriers so they can't jump out. That is done by screwing out the bottom stud of each door with a small, thin, included wrench. You need to raise the doors so they will be above any carpeting. While doing that, keep an eye on the tops of the doors and align them horizontally. -- dadiOH ____________________________ dadiOH's dandies v3.06... ....a help file of info about MP3s, recording from LP/cassette and tips & tricks on this and that. Get it at http://mysite.verizon.net/xico |
#7
Posted to alt.home.repair
|
|||
|
|||
Replace sliding doors with bi-fold
Well, even with the one pair I have on the downstairs closet, the bottom
pivot always seems to jump over 1-2 notches, putting the doors out of alignment. I'd rather T-frame the opening and install 2 sets of bifolds, but I'm just not sure whether it's okay to nail 2x4s right onto the existing drywall on the sides and celing. Would this be secure enough? dadiOH wrote: Pat Coghlan wrote: Interesting. Never saw that done before. Must be tricky to get perfectly aligned. It's hard enough keeping just one set of bifolds aligned. No, it isn't hard. Each bifold door section has pivot points at the top and bottom edges near the outside vertical edge. The doors have metal studs that fit into holes in carriers in the top track and on the floor. The carriers are moveable laterally. That means you can move the door sections a bit horizontally and you can tip them off vertical if needed. To line them up, start with one section nearest a wall and align it vertically, leaving enough space next to the wall so it can open. Then set the next section in place, aligning it to the first and leaving enough space between the two so it can open. Repeat with all other sections. You may have to increase the space between sections to avoid a large gap between the last section and the wall. If there is too little space for the last section you either have to get the sections closer together or cut off a little. Once all are to your liking, you lock the moveable carriers in place with the integral bolts. There will always be a space between the outboard doors and the walls as they must rotate to open...that space can be covered with a small board attached to the wall. The next job is to lock the doors into the carriers so they can't jump out. That is done by screwing out the bottom stud of each door with a small, thin, included wrench. You need to raise the doors so they will be above any carpeting. While doing that, keep an eye on the tops of the doors and align them horizontally. |
#8
Posted to alt.home.repair
|
|||
|
|||
Replace sliding doors with bi-fold
Patrick Coghlan wrote:
Well, even with the one pair I have on the downstairs closet, the bottom pivot always seems to jump over 1-2 notches, putting the doors out of alignment. Then you need to tighten the bottom carrier so it can't move. ____________________ I'd rather T-frame the opening and install 2 sets of bifolds, but I'm just not sure whether it's okay to nail 2x4s right onto the existing drywall on the sides and celing. Would this be secure enough? No. Not unless there is wood behind the drywall. If not, you'd have to use molly bolts. Or toggle bolts. Or similar. -- dadiOH ____________________________ dadiOH's dandies v3.06... ....a help file of info about MP3s, recording from LP/cassette and tips & tricks on this and that. Get it at http://mysite.verizon.net/xico |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Replacing bi-fold doors with conventional doors | Home Repair | |||
Convert Bi-Fold Doors to Small French Doors | Woodworking | |||
Bi-Fold doors | UK diy | |||
Replace patio sliding doors | Home Ownership | |||
Bi-Fold Doors | Home Ownership |