Wall boxes for sconces
 

I was in the process of mounting the boxes for sconce lights and I noticed
that the boxes are rather imprecise and difficult to mount. I'm reasonably
sure I didn't have cheap boxes and when I looked around I only found them in
this style, or some facimile thereof.

http://www.lowes.com/lowes/lkn?actio...20H&lpage=none

That's a good estimate of what I figured would work. NOPE, the nails are
difficult to drive in because they go in at an angle, the box is tough to
position properly because there is no markings on it, and it doesn't even
lay flat against the stud.

Are there better choices for mounting sconces? I would prefer non-metallic,
as then it would have to be grounded as well. Small job, but it adds to the
tasks.

Wall boxes for sconces
 

You can use bar boxes, which are more easily adjustable


"Eigenvector" wrote in message
. ..
I was in the process of mounting the boxes for sconce lights and I noticed
that the boxes are rather imprecise and difficult to mount. I'm reasonably
sure I didn't have cheap boxes and when I looked around I only found them
in this style, or some facimile thereof.

http://www.lowes.com/lowes/lkn?actio...20H&lpage=none

That's a good estimate of what I figured would work. NOPE, the nails are
difficult to drive in because they go in at an angle, the box is tough to
position properly because there is no markings on it, and it doesn't even
lay flat against the stud.

Are there better choices for mounting sconces? I would prefer
non-metallic, as then it would have to be grounded as well. Small job,
but it adds to the tasks.

Wall boxes for sconces
 

When I installed a wall lighting fixture I used the rectangular "J-box"
usually used for outlets and switches.

Wall boxes for sconces
 

"RBM" rbm2(remove wrote in message
...
You can use bar boxes, which are more easily adjustable

You're talking about those fan-stabilizer bar boxes. I wasn't sure if those
would fit a normal wall stud spacing or not


"Eigenvector" wrote in message
. ..
I was in the process of mounting the boxes for sconce lights and I noticed
that the boxes are rather imprecise and difficult to mount. I'm
reasonably sure I didn't have cheap boxes and when I looked around I only
found them in this style, or some facimile thereof.

http://www.lowes.com/lowes/lkn?actio...20H&lpage=none

That's a good estimate of what I figured would work. NOPE, the nails are
difficult to drive in because they go in at an angle, the box is tough to
position properly because there is no markings on it, and it doesn't even
lay flat against the stud.

Are there better choices for mounting sconces? I would prefer
non-metallic, as then it would have to be grounded as well. Small job,
but it adds to the tasks.

Wall boxes for sconces
 

"John Gilmer" wrote in message
...
When I installed a wall lighting fixture I used the rectangular "J-box"
usually used for outlets and switches.


Those don't have screws holes for the mounting plate though(???)

Wall boxes for sconces
 

On Thu, 9 Nov 2006 17:13:43 -0800, "Eigenvector"
wrote:

I was in the process of mounting the boxes for sconce lights and I noticed
that the boxes are rather imprecise and difficult to mount. I'm reasonably
sure I didn't have cheap boxes and when I looked around I only found them in
this style, or some facimile thereof.

http://www.lowes.com/lowes/lkn?actio...20H&lpage=none

That's a good estimate of what I figured would work. NOPE, the nails are
difficult to drive in because they go in at an angle, the box is tough to
position properly because there is no markings on it, and it doesn't even
lay flat against the stud.

Are there better choices for mounting sconces? I would prefer non-metallic,
as then it would have to be grounded as well. Small job, but it adds to the
tasks.


See if you can find these at a local electrical distributor:

http://www.smartboxinc.com/

HTH,

Paul

Wall boxes for sconces
 

No, I'm referring to standard fixture mounting bar boxes. They're made for
16 and 24 inch openings



"Eigenvector" wrote in message
...

"RBM" rbm2(remove wrote in message
...
You can use bar boxes, which are more easily adjustable

You're talking about those fan-stabilizer bar boxes. I wasn't sure if
those would fit a normal wall stud spacing or not


"Eigenvector" wrote in message
. ..
I was in the process of mounting the boxes for sconce lights and I
noticed that the boxes are rather imprecise and difficult to mount. I'm
reasonably sure I didn't have cheap boxes and when I looked around I only
found them in this style, or some facimile thereof.

http://www.lowes.com/lowes/lkn?actio...20H&lpage=none

That's a good estimate of what I figured would work. NOPE, the nails
are difficult to drive in because they go in at an angle, the box is
tough to position properly because there is no markings on it, and it
doesn't even lay flat against the stud.

Are there better choices for mounting sconces? I would prefer
non-metallic, as then it would have to be grounded as well. Small job,
but it adds to the tasks.

Wall boxes for sconces
 

Those don't have screws holes for the mounting plate though(???)


Seemed to me that the "mounting plate" (actually a steel strip about 3/4"
wide) had holes or slots to mount on the J-box. The mounting arrangements
for light fixtures are pretty flexible. There are TWO common sizes of
round boxes, for example. If you already have the fixture in hand you can
quickly check whether a J-box screw spacing is OK. If you don't have a
J-box lying about, just take the cover plate off anyout and measure the
screw spacing.

Wall boxes for sconces
 

"Paul Franklin" wrote in message
...
On Thu, 9 Nov 2006 17:13:43 -0800, "Eigenvector"
wrote:

I was in the process of mounting the boxes for sconce lights and I noticed
that the boxes are rather imprecise and difficult to mount. I'm
reasonably
sure I didn't have cheap boxes and when I looked around I only found them
in
this style, or some facimile thereof.

http://www.lowes.com/lowes/lkn?actio...20H&lpage=none

That's a good estimate of what I figured would work. NOPE, the nails are
difficult to drive in because they go in at an angle, the box is tough to
position properly because there is no markings on it, and it doesn't even
lay flat against the stud.

Are there better choices for mounting sconces? I would prefer
non-metallic,
as then it would have to be grounded as well. Small job, but it adds to
the
tasks.


See if you can find these at a local electrical distributor:

http://www.smartboxinc.com/

HTH,

Paul


Those look pretty slick, can't find a distributor in Canada though, pity.

PV

Wall boxes for sconces
 

Eigenvector wrote:

http://www.lowes.com/lowes/lkn?actio...20H&lpage=none

The nails are
difficult to drive in because they go in at an angle, the box is tough to
position properly because there is no markings on it, and it doesn't even
lay flat against the stud.

Are there better choices for mounting sconces? I would prefer non-metallic,
as then it would have to be grounded as well. Small job, but it adds to the
tasks.

Ev:

I like steel boxes, and would use a 4" octagon with a TS bracket, but
that's another
story.

The regular Carlon boxes can certainly be used, but perhaps a more
rigid
plastic box like the Carlon Super Blue would deform less and hold its
position better:

http://www.carlon.com/scripts/emAlbu...es&img=59&tn=1

I have used the device boxes in this line. They are very nice (for
plastic boxes).
I'm just a material bigot, it seems.

To help your box position properly, try cutting a small square of your
drywall, then holding
it against the stud, and holding the box flush with that.

Tap both nails in a bit before driving either one all the way home.

I assume that this is all new work.

Cordially yours:
G P

Wall boxes for sconces
 

wrote in message
oups.com...

Eigenvector wrote:

http://www.lowes.com/lowes/lkn?actio...20H&lpage=none

The nails are
difficult to drive in because they go in at an angle, the box is tough to
position properly because there is no markings on it, and it doesn't even
lay flat against the stud.

Are there better choices for mounting sconces? I would prefer
non-metallic,
as then it would have to be grounded as well. Small job, but it adds to
the
tasks.

Ev:

I like steel boxes, and would use a 4" octagon with a TS bracket, but
that's another
story.

The regular Carlon boxes can certainly be used, but perhaps a more
rigid
plastic box like the Carlon Super Blue would deform less and hold its
position better:

http://www.carlon.com/scripts/emAlbu...es&img=59&tn=1

I have used the device boxes in this line. They are very nice (for
plastic boxes).
I'm just a material bigot, it seems.

To help your box position properly, try cutting a small square of your
drywall, then holding
it against the stud, and holding the box flush with that.

Tap both nails in a bit before driving either one all the way home.

I assume that this is all new work.

Cordially yours:
G P


Well I went with the wall brace style. They seem to hold fine and having
two locations to mount helps me keep it level.