My fiancé and I just moved into our home, and my future father-in-law and I
are going to be redoing the wiring, due to the fact that a microwave or a
baby monitor will trip the breakers.

The way the main feed into the panel is cut, I am unable to see the amperage
of the line. Is there any way to tell the amperage from looking on the
meter outside of the house? Or possibly some other way?

Thanks

Ray

You should be able to tell by the size of the entrance conductors


"Ray DeVoe" wrote in message
. ..
My fiancé and I just moved into our home, and my future father-in-law and
I
are going to be redoing the wiring, due to the fact that a microwave or a
baby monitor will trip the breakers.

The way the main feed into the panel is cut, I am unable to see the
amperage
of the line. Is there any way to tell the amperage from looking on the
meter outside of the house? Or possibly some other way?

Thanks

Ray

"Ray DeVoe" wrote in message
. ..
My fiancé and I just moved into our home, and my future father-in-law and
I
are going to be redoing the wiring, due to the fact that a microwave or a
baby monitor will trip the breakers.

The way the main feed into the panel is cut, I am unable to see the
amperage
of the line. Is there any way to tell the amperage from looking on the
meter outside of the house? Or possibly some other way?

Takes a lot of guts to do your own wiring when you have to ask a question
like this.
Good luck!

On Thu, 20 Jul 2006 21:18:49 -0400, with neither quill nor qualm, "Ray
DeVoe" quickly quoth:

My fiancé and I just moved into our home, and my future father-in-law and I
are going to be redoing the wiring, due to the fact that a microwave or a
baby monitor will trip the breakers.

I can see the nuker popping a breaker but a baby monitor?!? What kind
of draw do those little radios take, maybe twenty watts? (It'll be on
the label underneath, like "120vac 20w") If a light load like that
pops the breaker, there's a real problem.


The way the main feed into the panel is cut, I am unable to see the amperage
of the line. Is there any way to tell the amperage from looking on the
meter outside of the house? Or possibly some other way?

I'm not an electrician, but here's how I'd go about tracing it down.

Find your circuit breaker box. Plug a lamp into the outlet in
question. One of you can switch off circuits until the other says the
lights went off for the circuit you wanted to check. You'll then know
which size breaker controls it, but it's probably a 20A. Now you or
your FIL can use a micrometer or calipers to measure the diameter of
the romex wire going to that circuit. It's probably 12ga (0.080") or
14ga (0.064"). If it's smaller, it's new wiring time!

Now check every outlet and light switch in the house while you see how
many appliances/outlets share the one circuit. Mapping the house like
that can be very beneficial in troubleshooting electrical problems in
the future, too.

Chances are that something with a heavy load is also connected there.
To keep from blowing the circuit, you can move some of the appliances
off it or rewire a heavily loaded outlet to a less heavily loaded
circuit.

If nothing else heavy is on the circuit, go to the electrical supply
store and get a good commercial duty breaker. They're about $17 vs. $6
for a consumer duty breaker. Replace the guilty breaker and see if it
still gives you problems. When you replace it, note any loose wires to
the breaker. If there is a loose connection, big loads will turn into
resistance and heat up the wire at the breaker, making it think it's
overloaded. That can also trip it.

If you still have problems, pull the wiring to that circuit and check
it closely. You'll probably see a problem. Replace that romex.

G'luck!

--
Heard of the Frisbee Religion? They believe that when you die,
your soul goes up on the roof and you can't get it down.
----
http://diversify.com Comprehensive Website Development

"Ray DeVoe" wrote in message
. ..
My fiancé and I just moved into our home, and my future father-in-law and
I
are going to be redoing the wiring, due to the fact that a microwave or a
baby monitor will trip the breakers.

It is unlikely that a baby monitor would trip a breaker all by itself.
The problem could be

(1) faulty breaker
(2) another high drain device being used at the same time as the baby
monitor/microwave
(3) faulty wiring (e.g. some sort of semi-short circuit) (unlikely)
(4) faulty baby monitor (unlikely)

I suggest you fully investigate the problem before you redo the wiring.

Larry Jaques wrote:
On Thu, 20 Jul 2006 21:18:49 -0400, with neither quill nor qualm, "Ray
DeVoe" quickly quoth:

...

I can see the nuker popping a breaker but a baby monitor?!? What kind
of draw do those little radios take, maybe twenty watts? (It'll be on
the label underneath, like "120vac 20w") If a light load like that
pops the breaker, there's a real problem.


My guess is it's a GFI tripping not a circuit breaker (unless they are
combined) If I am right, I sure hope the OP chooses to go with a
professional for this work as there is a major lack of general knowledge
about wiring among those who are planning to do the work.

--
Joseph Meehan

Dia duit