Can I use a diamond hole saw on wood?
 

I need to cut a 3/4" hole in a piece of engineered flooring. The hole needs
to have very clean and sharp edges.

Harbor Freight sells a diamond hole saw set for 6.99 (# 32399). Will a
diamond hole saw make clean cuts in wood, or will it chew up the edges of
the hole?

Is there anything that would work better than a diamond hole saw? An auger
bit or a Forstner bit?

Thanks

--
Walter
www.rationality.net
-

Can I use a diamond hole saw on wood?
 

On 2006-07-17, Walter R. wrote:

I need to cut a 3/4" hole in a piece of engineered flooring. The
hole needs to have very clean and sharp edges. Harbor Freight sells
a diamond hole saw set for 6.99 (# 32399). Will a diamond hole saw
make clean cuts in wood, or will it chew up the edges of the hole?

I'm not expert, but I'm pretty sure that diamonds are used on
materials that need to be abraded (e.g. metal, stone), while wood
needs to be cut for a clean edge. I think your best bet is a sharp
Forstner bit.

Cheers, Wayne

Can I use a diamond hole saw on wood?
 

Walter R. wrote:
I need to cut a 3/4" hole in a piece of engineered flooring. The hole needs
to have very clean and sharp edges.

Harbor Freight sells a diamond hole saw set for 6.99 (# 32399). Will a
diamond hole saw make clean cuts in wood, or will it chew up the edges of
the hole?

Is there anything that would work better than a diamond hole saw? An auger
bit or a Forstner bit?

Thanks

--
Walter
www.rationality.net

a diamond bit will burn a hole. i think a regular hole saw will work
better. a forstner bit would be the thing, but only if you have a
drill press. A brad point is another good option. even a spade bit,
the kind with the leader points on the sides would probably work OK.
-

Can I use a diamond hole saw on wood?
 

As others said a forester bit would work well or even a spade bit. Key is
keeping the drill motionless.


"Walter R." wrote in message
...
I need to cut a 3/4" hole in a piece of engineered flooring. The hole needs
to have very clean and sharp edges.

Harbor Freight sells a diamond hole saw set for 6.99 (# 32399). Will a
diamond hole saw make clean cuts in wood, or will it chew up the edges of
the hole?

Is there anything that would work better than a diamond hole saw? An
auger bit or a Forstner bit?

Thanks

--
Walter
www.rationality.net
-

Can I use a diamond hole saw on wood?
 

I just did a bunch of flooring.
I used a new spade bit and the holes look fine.

A forstner or even a wood boring bit would work too.

I wouldn't use a hole saw because they tend to walk until the saw part
starts to actually cut.

I don't know if they make one in 3/4", but a plug cutter could work.

Can I use a diamond hole saw on wood?
 

Walter R. wrote:

I need to cut a 3/4" hole in a piece of engineered flooring. The hole needs
to have very clean and sharp edges.

Harbor Freight sells a diamond hole saw set for 6.99 (# 32399). Will a
diamond hole saw make clean cuts in wood, or will it chew up the edges of
the hole?

Is there anything that would work better than a diamond hole saw? An auger
bit or a Forstner bit?

Thanks


Use a good Forstner. It cuts and won't walk on you. The diamond hole saw
just grinds and will burn your hole, that's if it gets through the
flooring before smoking you out.

--
Grandpa

What is that dripping from my fingers?
Why it looks like time.

Can I use a diamond hole saw on wood?
 

"Walter R." wrote in message
...
I need to cut a 3/4" hole in a piece of engineered flooring. The hole needs
to have very clean and sharp edges.

Harbor Freight sells a diamond hole saw set for 6.99 (# 32399). Will a
diamond hole saw make clean cuts in wood, or will it chew up the edges of
the hole?

Is there anything that would work better than a diamond hole saw? An
auger bit or a Forstner bit?

Thanks

--
Walter
www.rationality.net

Do you really expect anything from Harbor Freight to give you a perfect
hole? I wouldn't.
A diamond saw will not work well in wood. Go to Lee Valley's website and
order yourself either a
3/4" Forstner or brad point bit. The forstner will mandate a much steadier
hand (or drill press) but should give
you a superior hole.
Cheers,
cc

Can I use a diamond hole saw on wood?
 

Walter R. wrote:
I need to cut a 3/4" hole in a piece of engineered flooring. The hole
needs to have very clean and sharp edges.

But, over time, the hole won't stay that way. Consider an ordinary hole with
a plastic, cable access, shim/plug.

Can I use a diamond hole saw on wood?
 

In article ,
says...
On 2006-07-17, Walter R. wrote:

I need to cut a 3/4" hole in a piece of engineered flooring. The
hole needs to have very clean and sharp edges. Harbor Freight sells
a diamond hole saw set for 6.99 (# 32399). Will a diamond hole saw
make clean cuts in wood, or will it chew up the edges of the hole?

I'm not expert, but I'm pretty sure that diamonds are used on
materials that need to be abraded (e.g. metal, stone), while wood
needs to be cut for a clean edge. I think your best bet is a sharp
Forstner bit.

I agree with Wayne. A Forstner bit is the right tool for the job.
I used one to drill 1" holes in my bamboo floor for water lines
(dishwasher and ice maker) and power (stove). It made a nice sharp
hole in the bamboo (which is harder than any domestic hardwood).

--
Keith

Can I use a diamond hole saw on wood?
 

In article .com,
says...

Walter R. wrote:
I need to cut a 3/4" hole in a piece of engineered flooring. The hole needs
to have very clean and sharp edges.

Harbor Freight sells a diamond hole saw set for 6.99 (# 32399). Will a
diamond hole saw make clean cuts in wood, or will it chew up the edges of
the hole?

Is there anything that would work better than a diamond hole saw? An auger
bit or a Forstner bit?

Thanks

--
Walter
www.rationality.net

a diamond bit will burn a hole. i think a regular hole saw will work
better. a forstner bit would be the thing, but only if you have a
drill press. A brad point is another good option. even a spade bit,
the kind with the leader points on the sides would probably work OK.

You don't need a drill press for a 3/4" Forstner bit. A cordless
drill will work fine. ;-)

--
Keith

Can I use a diamond hole saw on wood?
 

If you're lucky, the flooring is not yet down. No matter what type of
drill bit you use, drill only half way down and then flip the board over
and finish the cut. This will avoid splintering as the bit completes
the cut.

HeyBub wrote:
Walter R. wrote:
I need to cut a 3/4" hole in a piece of engineered flooring. The hole
needs to have very clean and sharp edges.

But, over time, the hole won't stay that way. Consider an ordinary hole with
a plastic, cable access, shim/plug.

Can I use a diamond hole saw on wood?
 

"James "Cubby" Culbertson" wrote in message
. ..

"Walter R." wrote in message
...
I need to cut a 3/4" hole in a piece of engineered flooring. The hole
needs to have very clean and sharp edges.

Harbor Freight sells a diamond hole saw set for 6.99 (# 32399). Will a
diamond hole saw make clean cuts in wood, or will it chew up the edges of
the hole?

Is there anything that would work better than a diamond hole saw? An
auger bit or a Forstner bit?

Thanks

--
Walter
www.rationality.net

Do you really expect anything from Harbor Freight to give you a perfect
hole? I wouldn't.
A diamond saw will not work well in wood. Go to Lee Valley's website and
order yourself either a
3/4" Forstner or brad point bit. The forstner will mandate a much
steadier hand (or drill press) but should give
you a superior hole.
Cheers,
cc

I bought the HF Forstners in a weak moment. They didn't even have an edge
or any sharpness to the lead edge of the tooth. Save yourself the headache
and follow the suggestions of the others - especially the suggestion to
drill half way and then, complete the hole from the other side. You will
need to have your drill straight so the the intersection of the 'two' holes
is accurate or you will have a ridge in the center.

Can I use a diamond hole saw on wood?
 

"C & E" wrote in message
...
I bought the HF Forstners in a weak moment. They didn't even have an edge
or any sharpness to the lead edge of the tooth.

That's why I recommended buying a quality bit from Lee Valley. I will buy a
bunch of stuff from HF for the stuff I don't need precision or long life.
In fact, all my vehicles have a set of tools by HF. I won't buy stuff
where I need precision or quality results (ie. drill bits, chisels, etc...).
Cheers,
cc

Can I use a diamond hole saw on wood?
 

I've used a diamond hole saw on wood and it does work, but slowly (about 1 minute for 3/4" pine. The top of the hole was cleanly cut, but there was black scorching inside the hole, and a rough exit hole. I made a video of all of this on youtube. You can watch it he https://www.youtube.com/watch?v=n6cMfDtzQu8

Can I use a diamond hole saw on wood?
 

On Tue, 20 Jun 2017 14:12:33 -0700 (PDT), wrote:

I've used a diamond hole saw on wood and it does work, but slowly (about 1 minute for 3/4" pine. The top of the hole was cleanly cut, but there was black scorching inside the hole, and a rough exit hole. I made a video of all of this on youtube. You can watch it he https://www.youtube.com/watch?v=n6cMfDtzQu8

It's possible to get the saw so hot that it weakens the braze that holds the diamonds in place.
In other words, it could be a quick trick for cleaning the diamonds off the saw... ;-)

--
croy

Can I use a diamond hole saw on wood?
 

On 6/21/2017 2:14 PM, croy wrote:
On Tue, 20 Jun 2017 14:12:33 -0700 (PDT), wrote:

I've used a diamond hole saw on wood and it does work, but slowly (about 1 minute for 3/4" pine. The top of the hole was cleanly cut, but there was black scorching inside the hole, and a rough exit hole. I made a video of all of this on youtube. You can watch it he https://www.youtube.com/watch?v=n6cMfDtzQu8

It's possible to get the saw so hot that it weakens the braze that holds the diamonds in place.
In other words, it could be a quick trick for cleaning the diamonds off the saw... ;-)


That was my thinking too.

Can I use a diamond hole saw on wood?
 

On Wed, 21 Jun 2017 11:14:56 -0700, croy
wrote:

On Tue, 20 Jun 2017 14:12:33 -0700 (PDT), wrote:

I've used a diamond hole saw on wood and it does work, but slowly (about 1 minute for 3/4" pine. The top of the hole was cleanly cut, but there was black scorching inside the hole, and a rough exit hole. I made a video of all of this on youtube. You can watch it he https://www.youtube.com/watch?v=n6cMfDtzQu8

It's possible to get the saw so hot that it weakens the braze that holds the diamonds in place.
In other words, it could be a quick trick for cleaning the diamonds off the saw... ;-)
The big question is WHY WOULD YOU?????

Can I use a diamond hole saw on wood?
 

replying to clare, ThriftyTani wrote:
Someone wanted to drill a hole in marble, but also needed to cut a hole
through the wood that was underneath it. He wanted to know if he needed spend
an extra $10-25 on a wood hole saw just to cut 1 or 2 holes.

--
for full context, visit https://www.homeownershub.com/mainte...od-129203-.htm