DIYbanter

DIYbanter (https://www.diybanter.com/)
-   Home Repair (https://www.diybanter.com/home-repair/)
-   -   Condensation in dryer vent line (https://www.diybanter.com/home-repair/147441-condensation-dryer-vent-line.html)

DL March 4th 06 04:11 AM

Condensation in dryer vent line
 
I noticed the other day that when my wife was doing a considerable amount of
drying, that there was condensation in the dryer vent piping.

The piping comes from the upper floor, down through the main level into the
basement and then goes to an exterior wall and exits our home.

I noticed dripping from the vent piping at the 90 degree turn in the
basement where it comes from the upper levels.

Is this normal? Don't know that I have ever noticed this before, mainly
because it is not something have ever looked for.

David



RBM March 4th 06 12:14 PM

Condensation in dryer vent line
 
Sounds like the vent pipe may be to long. Check with the dryer manufacturer
as to the maximum length and bends allowable for the machine. You have
hot,moist air flowing through it, and the longer it is, the more opportunity
it has to cool and condense



"DL" wrote in message
news:Rr8Of.28419$2c4.23147@dukeread11...
I noticed the other day that when my wife was doing a considerable amount
of drying, that there was condensation in the dryer vent piping.

The piping comes from the upper floor, down through the main level into
the basement and then goes to an exterior wall and exits our home.

I noticed dripping from the vent piping at the 90 degree turn in the
basement where it comes from the upper levels.

Is this normal? Don't know that I have ever noticed this before, mainly
because it is not something have ever looked for.

David




John Grabowski March 4th 06 12:58 PM

Condensation in dryer vent line
 

"DL" wrote in message
news:Rr8Of.28419$2c4.23147@dukeread11...
I noticed the other day that when my wife was doing a considerable amount

of
drying, that there was condensation in the dryer vent piping.

The piping comes from the upper floor, down through the main level into

the
basement and then goes to an exterior wall and exits our home.

I noticed dripping from the vent piping at the 90 degree turn in the
basement where it comes from the upper levels.

Is this normal? Don't know that I have ever noticed this before, mainly
because it is not something have ever looked for.

David



I had a similar problem with my dryer vent passing through the attic. I
insulated the duct with duct wrap and it has been fine since. You might
want to make sure that your vent pipe is clean. Too much lint will absorb
moisture and restrict air flow.


DL March 4th 06 01:26 PM

Condensation in dryer vent line
 
Good point. I will look into it.

The day she was doing the laundry and I noticed the condensation, it was a
very very cold day, which makes me think that I need to check the outside
vent to see if any cold air could be getting in.

I am also thinking about purchasing a dryer vent cleaning kit to make sure
that there is no major buildup of lint so that the dryer is able to properly
vent.

David

"RBM" rbm2(remove wrote in message
...
Sounds like the vent pipe may be to long. Check with the dryer
manufacturer as to the maximum length and bends allowable for the machine.
You have hot,moist air flowing through it, and the longer it is, the more
opportunity it has to cool and condense



"DL" wrote in message
news:Rr8Of.28419$2c4.23147@dukeread11...
I noticed the other day that when my wife was doing a considerable amount
of drying, that there was condensation in the dryer vent piping.

The piping comes from the upper floor, down through the main level into
the basement and then goes to an exterior wall and exits our home.

I noticed dripping from the vent piping at the 90 degree turn in the
basement where it comes from the upper levels.

Is this normal? Don't know that I have ever noticed this before, mainly
because it is not something have ever looked for.

David






DL March 4th 06 01:32 PM

Condensation in dryer vent line
 
Thanks for the advice.

Being in a heated basement, I am not sure the duct wrap is necessary, though
I did see a very lousy / non-existent attempt to tape the joints between the
sections of vent pipe. I agree that I should make sure that the ducts have
been cleaned.

David

"John Grabowski" wrote in message
...

"DL" wrote in message
news:Rr8Of.28419$2c4.23147@dukeread11...
I noticed the other day that when my wife was doing a considerable amount

of
drying, that there was condensation in the dryer vent piping.

The piping comes from the upper floor, down through the main level into

the
basement and then goes to an exterior wall and exits our home.

I noticed dripping from the vent piping at the 90 degree turn in the
basement where it comes from the upper levels.

Is this normal? Don't know that I have ever noticed this before, mainly
because it is not something have ever looked for.

David



I had a similar problem with my dryer vent passing through the attic. I
insulated the duct with duct wrap and it has been fine since. You might
want to make sure that your vent pipe is clean. Too much lint will absorb
moisture and restrict air flow.




EXT March 4th 06 02:43 PM

Condensation in dryer vent line
 
In my own situation, while I did not have moisture dripping, I found that
aluminium pipe draws the heat out causing condensation. The moisture inside
the pipe quickly gathers lint, so much that I was having to clean out the
pipes every 3 months. The 4 inch diameter tubes had about 1/2 to 3/4" of
lint stuck to the tube walls.

I replaced the run (this is for an electric dryer, do not do this for a gas
dryer) with 4" PVC sewer/drain pipe. I have not had to clean it out for the
past 12 years. The plastic pipe holds the heat in and prevents or reduces
any condensation. My idea to use PVC was based on seeing furnaces that used
ABS or PVC drain pipe as a vent.


"DL" wrote in message
news:tFgOf.28426$2c4.22227@dukeread11...
Thanks for the advice.

Being in a heated basement, I am not sure the duct wrap is necessary,

though
I did see a very lousy / non-existent attempt to tape the joints between

the
sections of vent pipe. I agree that I should make sure that the ducts

have
been cleaned.

David

"John Grabowski" wrote in message
...

"DL" wrote in message
news:Rr8Of.28419$2c4.23147@dukeread11...
I noticed the other day that when my wife was doing a considerable

amount
of
drying, that there was condensation in the dryer vent piping.

The piping comes from the upper floor, down through the main level into

the
basement and then goes to an exterior wall and exits our home.

I noticed dripping from the vent piping at the 90 degree turn in the
basement where it comes from the upper levels.

Is this normal? Don't know that I have ever noticed this before,

mainly
because it is not something have ever looked for.

David



I had a similar problem with my dryer vent passing through the attic. I
insulated the duct with duct wrap and it has been fine since. You might
want to make sure that your vent pipe is clean. Too much lint will

absorb
moisture and restrict air flow.






whodat March 4th 06 02:43 PM

Condensation in dryer vent line
 

your dryer vent is definatly too long, no doubt about it.


--
whodat
------------------------------------------------------------------------
whodat's Profile: http://www.HomeOutfit.com/member.php?userid=35
View this thread: http://www.HomeOutfit.com/showthread.php?t=67674


DL March 4th 06 02:57 PM

Condensation in dryer vent line
 
Really good idea. though it would be major surgery to replace the 16' run
from the dryer upstairs (3rd level) to the basement.the basement run would
be simple. How did you connect from the dryer to the PVC?

I am almost scared as to what I will find in the vent ducts when I clean
them.

David

"EXT" etonks@sunstormADD-DOT-COM wrote in message
anews.com...
In my own situation, while I did not have moisture dripping, I found that
aluminium pipe draws the heat out causing condensation. The moisture
inside
the pipe quickly gathers lint, so much that I was having to clean out the
pipes every 3 months. The 4 inch diameter tubes had about 1/2 to 3/4" of
lint stuck to the tube walls.

I replaced the run (this is for an electric dryer, do not do this for a
gas
dryer) with 4" PVC sewer/drain pipe. I have not had to clean it out for
the
past 12 years. The plastic pipe holds the heat in and prevents or reduces
any condensation. My idea to use PVC was based on seeing furnaces that
used
ABS or PVC drain pipe as a vent.


"DL" wrote in message
news:tFgOf.28426$2c4.22227@dukeread11...
Thanks for the advice.

Being in a heated basement, I am not sure the duct wrap is necessary,

though
I did see a very lousy / non-existent attempt to tape the joints between

the
sections of vent pipe. I agree that I should make sure that the ducts

have
been cleaned.

David

"John Grabowski" wrote in message
...

"DL" wrote in message
news:Rr8Of.28419$2c4.23147@dukeread11...
I noticed the other day that when my wife was doing a considerable

amount
of
drying, that there was condensation in the dryer vent piping.

The piping comes from the upper floor, down through the main level
into
the
basement and then goes to an exterior wall and exits our home.

I noticed dripping from the vent piping at the 90 degree turn in the
basement where it comes from the upper levels.

Is this normal? Don't know that I have ever noticed this before,

mainly
because it is not something have ever looked for.

David



I had a similar problem with my dryer vent passing through the attic.
I
insulated the duct with duct wrap and it has been fine since. You
might
want to make sure that your vent pipe is clean. Too much lint will

absorb
moisture and restrict air flow.








EXT March 4th 06 04:46 PM

Condensation in dryer vent line
 
I used a short length of flexible vinyl tubing, just enough to allow me to
make the connection and move the dryer that last few inches against the wall
after I had extracted myself. Had to reduce the diameter of the PVC sewer
pipe slightly to fit the vinyl tubing over it. Used a heat gun to soften the
pipe and a tightened large gear clamp to shrink the diameter until it was
the right size. Worked like a charm.

"DL" wrote in message
news:7VhOf.28448$2c4.11702@dukeread11...
Really good idea. though it would be major surgery to replace the 16' run
from the dryer upstairs (3rd level) to the basement.the basement run would
be simple. How did you connect from the dryer to the PVC?

I am almost scared as to what I will find in the vent ducts when I clean
them.

David

"EXT" etonks@sunstormADD-DOT-COM wrote in message
anews.com...
In my own situation, while I did not have moisture dripping, I found

that
aluminium pipe draws the heat out causing condensation. The moisture
inside
the pipe quickly gathers lint, so much that I was having to clean out

the
pipes every 3 months. The 4 inch diameter tubes had about 1/2 to 3/4" of
lint stuck to the tube walls.

I replaced the run (this is for an electric dryer, do not do this for a
gas
dryer) with 4" PVC sewer/drain pipe. I have not had to clean it out for
the
past 12 years. The plastic pipe holds the heat in and prevents or

reduces
any condensation. My idea to use PVC was based on seeing furnaces that
used
ABS or PVC drain pipe as a vent.


"DL" wrote in message
news:tFgOf.28426$2c4.22227@dukeread11...
Thanks for the advice.

Being in a heated basement, I am not sure the duct wrap is necessary,

though
I did see a very lousy / non-existent attempt to tape the joints

between
the
sections of vent pipe. I agree that I should make sure that the ducts

have
been cleaned.

David

"John Grabowski" wrote in message
...

"DL" wrote in message
news:Rr8Of.28419$2c4.23147@dukeread11...
I noticed the other day that when my wife was doing a considerable

amount
of
drying, that there was condensation in the dryer vent piping.

The piping comes from the upper floor, down through the main level
into
the
basement and then goes to an exterior wall and exits our home.

I noticed dripping from the vent piping at the 90 degree turn in the
basement where it comes from the upper levels.

Is this normal? Don't know that I have ever noticed this before,

mainly
because it is not something have ever looked for.

David



I had a similar problem with my dryer vent passing through the attic.
I
insulated the duct with duct wrap and it has been fine since. You
might
want to make sure that your vent pipe is clean. Too much lint will

absorb
moisture and restrict air flow.










CDET 14 March 4th 06 05:58 PM

Condensation in dryer vent line
 
16' is not too long for a dryer vent, although the shorter the better.
Have you considered terminating the vent to the exterior near the
dryer?
If you need help with the cleanout, which is clearly needed, visit
http://CleanYourOwnDryerVent.com


DL wrote:
Really good idea. though it would be major surgery to replace the 16' run
from the dryer upstairs (3rd level) to the basement.the basement run would
be simple. How did you connect from the dryer to the PVC?

I am almost scared as to what I will find in the vent ducts when I clean
them.

David

"EXT" etonks@sunstormADD-DOT-COM wrote in message
anews.com...
In my own situation, while I did not have moisture dripping, I found that
aluminium pipe draws the heat out causing condensation. The moisture
inside
the pipe quickly gathers lint, so much that I was having to clean out the
pipes every 3 months. The 4 inch diameter tubes had about 1/2 to 3/4" of
lint stuck to the tube walls.

I replaced the run (this is for an electric dryer, do not do this for a
gas
dryer) with 4" PVC sewer/drain pipe. I have not had to clean it out for
the
past 12 years. The plastic pipe holds the heat in and prevents or reduces
any condensation. My idea to use PVC was based on seeing furnaces that
used
ABS or PVC drain pipe as a vent.


"DL" wrote in message
news:tFgOf.28426$2c4.22227@dukeread11...
Thanks for the advice.

Being in a heated basement, I am not sure the duct wrap is necessary,

though
I did see a very lousy / non-existent attempt to tape the joints between

the
sections of vent pipe. I agree that I should make sure that the ducts

have
been cleaned.

David

"John Grabowski" wrote in message
...

"DL" wrote in message
news:Rr8Of.28419$2c4.23147@dukeread11...
I noticed the other day that when my wife was doing a considerable

amount
of
drying, that there was condensation in the dryer vent piping.

The piping comes from the upper floor, down through the main level
into
the
basement and then goes to an exterior wall and exits our home.

I noticed dripping from the vent piping at the 90 degree turn in the
basement where it comes from the upper levels.

Is this normal? Don't know that I have ever noticed this before,

mainly
because it is not something have ever looked for.

David



I had a similar problem with my dryer vent passing through the attic.
I
insulated the duct with duct wrap and it has been fine since. You
might
want to make sure that your vent pipe is clean. Too much lint will

absorb
moisture and restrict air flow.








All times are GMT +1. The time now is 07:56 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter