need a little help in configuring a combination of Trane xl1800 (X) and Climatouch
Thermostat (CT) in S.Florida
The CT is model CT03TS32H (3H+2C+HUM)

the X is a heatpump and it's currently defined in the CT Advanced Settings as "Heat
Pump" and not as a 2-stage Heat Pump (I will assume that is correct for now although
the X is a dual-compressor unit)

my goal is to keep humidity below 60% and temp below 78F and both functions to be
independent of each other

in the CT Main Menu, the Humidify/Dehumidify setting is set to "Dehumidify" and Temp
Control Mode to "Cool"
there was a setting for "Heat/Cool" but as I never need heat (not even when temp in
S.Florida drops below 45F) I have it only on "Cool"

under CT Advanced Settings the following settings are giving me some trouble

Hum Fam (HF) is set to OFF
DH Fan (DF) is set to ON
DH Reverse (DR) is set to OFF
DH Control Comp (DCC) is set to OFF

Target "Cool" setting is set to 78F and Dehumidify to 60%

Problem is that if I change DR to ON, the unit runs continuously (the low side
compressor) even when humidity reaches below 60% and currently S.Florida outside temps
are in the 60's so only the dehumidify function should be running. If I change DR to
OFF, the low side compressor turns off but I lose the Dehumidify function and the X
will not come on even when inside humidity goes above 60%

I have the green wire on the CT going from right side contact point 7 to left side
contact point 4

in the CT manual the explanation for the DR settings states:
ON: DH relay is normally closed when relative humidity is above DH set point
OFF: DH relay is normally open when relative humidity is above DH set point

the DCC explanation shows that OFF setting means the DH relay is independent (which I
do want) of compressor activity

"lvc" wrote in message
...
need a little help in configuring a combination of Trane xl1800 (X) and
Climatouch Thermostat (CT) in S.Florida
The CT is model CT03TS32H (3H+2C+HUM)

the X is a heatpump and it's currently defined in the CT Advanced Settings
as "Heat Pump" and not as a 2-stage Heat Pump (I will assume that is
correct for now although the X is a dual-compressor unit)

my goal is to keep humidity below 60% and temp below 78F and both
functions to be independent of each other

in the CT Main Menu, the Humidify/Dehumidify setting is set to
"Dehumidify" and Temp Control Mode to "Cool"
there was a setting for "Heat/Cool" but as I never need heat (not even
when temp in S.Florida drops below 45F) I have it only on "Cool"

under CT Advanced Settings the following settings are giving me some
trouble

Hum Fam (HF) is set to OFF
DH Fan (DF) is set to ON
DH Reverse (DR) is set to OFF
DH Control Comp (DCC) is set to OFF

Target "Cool" setting is set to 78F and Dehumidify to 60%

Problem is that if I change DR to ON, the unit runs continuously (the low
side compressor) even when humidity reaches below 60% and currently
S.Florida outside temps are in the 60's so only the dehumidify function
should be running. If I change DR to OFF, the low side compressor turns
off but I lose the Dehumidify function and the X will not come on even
when inside humidity goes above 60%

I have the green wire on the CT going from right side contact point 7 to
left side contact point 4

in the CT manual the explanation for the DR settings states:
ON: DH relay is normally closed when relative humidity is above DH set
point
OFF: DH relay is normally open when relative humidity is above DH set
point

the DCC explanation shows that OFF setting means the DH relay is
independent (which I do want) of compressor activity





Where did you go to school, boy? You need to develop skills in sentences
structure, grammar, and punctuation.

If you can't even speak English properly, how the hell do you think you can
handle complex machinery?