Home |
Search |
Today's Posts |
|
Home Repair (alt.home.repair) For all homeowners and DIYers with many experienced tradesmen. Solve your toughest home fix-it problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
|
#1
|
|||
|
|||
Bathroom Exhaust Fan Conduit
Is it wise to use metallic tubing as the exhaust (4 inch diamter) conduit for a Panasonic model FV-08VQL3 ? Would metal tubing be prone to producing more noise than a plastic-covered ring tubing ? |
#2
|
|||
|
|||
If you're referring to MET tubing,you're way over the top. Just use 4 inch
steel duct or even flex duct "Vince" wrote in message ... Is it wise to use metallic tubing as the exhaust (4 inch diamter) conduit for a Panasonic model FV-08VQL3 ? Would metal tubing be prone to producing more noise than a plastic-covered ring tubing ? |
#3
|
|||
|
|||
that would be EMT
"RBM" rbm2(remove wrote in message ... If you're referring to MET tubing,you're way over the top. Just use 4 inch steel duct or even flex duct "Vince" wrote in message ... Is it wise to use metallic tubing as the exhaust (4 inch diamter) conduit for a Panasonic model FV-08VQL3 ? Would metal tubing be prone to producing more noise than a plastic-covered ring tubing ? |
#4
|
|||
|
|||
Is that 4 inch steel duct found at Home Depot ? The term "MET" is not part of my volcabulary. On Mon, 27 Jun 2005 20:06:08 -0400, "RBM" rbm2(remove wrote: If you're referring to MET tubing,you're way over the top. Just use 4 inch steel duct or even flex duct "Vince" wrote in message .. . Is it wise to use metallic tubing as the exhaust (4 inch diamter) conduit for a Panasonic model FV-08VQL3 ? Would metal tubing be prone to producing more noise than a plastic-covered ring tubing ? |
#5
|
|||
|
|||
I hit the spell check and it changed EMT to MET, which is electrical
metallic tubing. Which is much heavier than you'd want for duct. Depot sells standard steel 4 inch duct in three or four foot lengths, they also sell a pretty nice smooth interior flex duct. I've seen plastic dryer duct used, and as you indicated, condensation filled low, sagging areas with water "Vince" wrote in message ... Is that 4 inch steel duct found at Home Depot ? The term "MET" is not part of my volcabulary. On Mon, 27 Jun 2005 20:06:08 -0400, "RBM" rbm2(remove wrote: If you're referring to MET tubing,you're way over the top. Just use 4 inch steel duct or even flex duct "Vince" wrote in message . .. Is it wise to use metallic tubing as the exhaust (4 inch diamter) conduit for a Panasonic model FV-08VQL3 ? Would metal tubing be prone to producing more noise than a plastic-covered ring tubing ? |
#6
|
|||
|
|||
On Mon, 27 Jun 2005 23:35:38 GMT, Vince
wrote: Is it wise to use metallic tubing as the exhaust (4 inch diamter) conduit for a Panasonic model FV-08VQL3 ? Yes. Would metal tubing be prone to producing more noise than a plastic-covered ring tubing ? No, assuming the fan is installed correctly. -- Luke __________________________________________________ ____________________ "For bureaucratic reasons, we settled on one issue, weapons of mass destruction [as justification for invading Iraq], because it was the one reason everyone could agree on." -- Paul Wolfowitz, May 28, 2003 |
#7
|
|||
|
|||
On Mon, 27 Jun 2005 23:35:38 GMT, Vince wrote:
Is it wise to use metallic tubing as the exhaust (4 inch diamter) conduit for a Panasonic model FV-08VQL3 ? Would metal tubing be prone to producing more noise than a plastic-covered ring tubing ? Vince, I'm also planning to install a panasonic fan in my bathroom. Venting thru unheated attic to an outside wall. I'm thinking about using pvc pipe. I'm also looking for a way to insulate it! If you come up with any ideas please let me know. Have you bought the fan yet? I found what look like pretty good prices at www.rewci.com. They sell the fan you listed for $145 w/free shipping. Not sure if thats a good price, as the fan I'm looking at is a different model. I'm also planning to use a nice, push-button timer switch: http://www.smarthome.com/4253.HTML Again, if you get any good ideas or sources for insulating the 4" duct please let me know. |
#8
|
|||
|
|||
On Wed, 29 Jun 2005 22:20:28 -0700, Lee wrote:
On Mon, 27 Jun 2005 23:35:38 GMT, Vince wrote: Is it wise to use metallic tubing as the exhaust (4 inch diamter) conduit for a Panasonic model FV-08VQL3 ? Would metal tubing be prone to producing more noise than a plastic-covered ring tubing ? Vince, I'm also planning to install a panasonic fan in my bathroom. Venting thru unheated attic to an outside wall. I'm thinking about using pvc pipe. I'm also looking for a way to insulate it! If you come up with any ideas please let me know. Have you bought the fan yet? I found what look like pretty good prices at www.rewci.com. They sell the fan you listed for $145 w/free shipping. Not sure if thats a good price, as the fan I'm looking at is a different model. I'm also planning to use a nice, push-button timer switch: http://www.smarthome.com/4253.HTML Again, if you get any good ideas or sources for insulating the 4" duct please let me know. Hello Lee: I read in another post the suggestion of using PVC pipe as the conduit, and gave that some thought. I think steel conduit would work just as well as PVC. The problem that I might have here is that this ranch type house has a hip line roof, and there might not be enough room to angle the conduit to the vent opening that is already located in the soffit area on the house. I have been concentrating on using Owens-Corning Fiberglass Duct Wrap http://www.owenscorning.com/comminsu...erviceDuct.pdf as the insulating material, if I can easily obtain it w/o going crazy. I think Type 75 in 4 inch thickness will be OK. However, I have not as yet found where to buy and do not know pricing info. eBay has a couple of sellers for the Panasonic model FV-08VQL3 that I am keyed onto. Pricing is at about $142 with free shipping. Thanks for the tip; very much appreciated since I was thinking that I need a fixed timer for 20 mins or 30 mins. I will consider the count-down timer shown at http://www.smarthome.com/4253.HTML . I think that I must be careful of which model to select, because the FV-08VQL3 fan (rated at 0.7 SONE) includes two fluorescent bulbs and a socket for an incandescent night light. I don't need the night light, so I wont bother with a separate switch for it. The count-down timer, Leviton model 4254/4255-Ivory, will likely handle the fan motor and the fluorescent bulb loads. Or, I might want to go with a separate (normal) switch for the fluorescent load. Regards, de ~ Vince ~ |
#9
|
|||
|
|||
On Thu, 30 Jun 2005 12:08:16 GMT, Vince wrote:
Hello Lee: I read in another post the suggestion of using PVC pipe as the conduit, and gave that some thought. I think steel conduit would work just as well as PVC. The problem that I might have here is that this ranch type house has a hip line roof, and there might not be enough room to angle the conduit to the vent opening that is already located in the soffit area on the house. I have been concentrating on using Owens-Corning Fiberglass Duct Wrap http://www.owenscorning.com/comminsu...erviceDuct.pdf as the insulating material, if I can easily obtain it w/o going crazy. I think Type 75 in 4 inch thickness will be OK. However, I have not as yet found where to buy and do not know pricing info. eBay has a couple of sellers for the Panasonic model FV-08VQL3 that I am keyed onto. Pricing is at about $142 with free shipping. Thanks for the tip; very much appreciated since I was thinking that I need a fixed timer for 20 mins or 30 mins. I will consider the count-down timer shown at http://www.smarthome.com/4253.HTML . I think that I must be careful of which model to select, because the FV-08VQL3 fan (rated at 0.7 SONE) includes two fluorescent bulbs and a socket for an incandescent night light. I don't need the night light, so I wont bother with a separate switch for it. The count-down timer, Leviton model 4254/4255-Ivory, will likely handle the fan motor and the fluorescent bulb loads. Or, I might want to go with a separate (normal) switch for the fluorescent load. Regards, de ~ Vince ~ On the switch, in case you shop locally, the actual Leviton "Decora" number is 612-6230M. The number I previously provided must the the Smarthome catalog number of this switch. The Smarthome price beat what I could find locally however. |
#10
|
|||
|
|||
On Thu, 30 Jun 2005 12:08:16 GMT, Vince wrote:
Hello Lee: I read in another post the suggestion of using PVC pipe as the conduit, and gave that some thought. I think steel conduit would work just as well as PVC. The problem that I might have here is that this ranch type house has a hip line roof, and there might not be enough room to angle the conduit to the vent opening that is already located in the soffit area on the house. I have been concentrating on using Owens-Corning Fiberglass Duct Wrap http://www.owenscorning.com/comminsu...erviceDuct.pdf as the insulating material, if I can easily obtain it w/o going crazy. I think Type 75 in 4 inch thickness will be OK. However, I have not as yet found where to buy and do not know pricing info. eBay has a couple of sellers for the Panasonic model FV-08VQL3 that I am keyed onto. Pricing is at about $142 with free shipping. Thanks for the tip; very much appreciated since I was thinking that I need a fixed timer for 20 mins or 30 mins. I will consider the count-down timer shown at http://www.smarthome.com/4253.HTML . I think that I must be careful of which model to select, because the FV-08VQL3 fan (rated at 0.7 SONE) includes two fluorescent bulbs and a socket for an incandescent night light. I don't need the night light, so I wont bother with a separate switch for it. The count-down timer, Leviton model 4254/4255-Ivory, will likely handle the fan motor and the fluorescent bulb loads. Or, I might want to go with a separate (normal) switch for the fluorescent load. Regards, de ~ Vince ~ Vince, I forgot to mention that I found insulation that might work to cover ducting, at Home Depot. It was in the duct area, near the foil tape and such. Its foil backed sleeves of insulation for 6" ducts and smaller. Take a look. Its about $5.40 for 5 ft. Also thanks for the info on the duct wrap insulation. I'll check it out. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Bathroom Exhaust Fan | Home Repair | |||
Replacing Bathroom Ceiling Exhaust Fans... | Home Repair | |||
Bathroom Exhaust Fans to | Home Repair | |||
bathroom exhaust fan/heater | Home Repair | |||
Bathroom exhaust fan and dryer fan | Home Ownership |