Kenwood TM-V71A Transceiver Locked Up in Cross Band Repeater Mode
 

Hi,

I have a Kenwood TM-V71A 144/440mhz transceiver that is "locked up" in
CBR ("Cross Band Repeater") mode. Note: In this mode, the Kenwood radio
"acts" like a repeater.

When this transceiver is set for CBR mode, most other functions are
disabled. I am unable to get it out of CBR mode. Note: I have used
CBR mode many times, and I never had a problem getting the radio our of CBR
mode until recently.

I have the SM (.pdf) and tried the "Full Reset" procedure and the
"Adjustment Mode" procedure, but nothing happens. CBR mode
prevents these other procedures from taking "effect".

This transceiver does not use an internal battery to hold memory
settings, etc. Instead, it uses an eeprom.

I searched the web for a solution, but found none. I also used "contact
us" at Kenwood's web site, but I have not received a response to the problem,
only an acknowledgement they received my message.

Thank You in advance, John N3AOF

Kenwood TM-V71A Transceiver Locked Up in Cross Band RepeaterMode
 

On 10/09/2013 14:45, wrote:
Hi,

I have a Kenwood TM-V71A 144/440mhz transceiver that is "locked up" in
CBR ("Cross Band Repeater") mode. Note: In this mode, the Kenwood radio
"acts" like a repeater.

When this transceiver is set for CBR mode, most other functions are
disabled. I am unable to get it out of CBR mode. Note: I have used
CBR mode many times, and I never had a problem getting the radio our of CBR
mode until recently.

I have the SM (.pdf) and tried the "Full Reset" procedure and the
"Adjustment Mode" procedure, but nothing happens. CBR mode
prevents these other procedures from taking "effect".

This transceiver does not use an internal battery to hold memory
settings, etc. Instead, it uses an eeprom.

I searched the web for a solution, but found none. I also used "contact
us" at Kenwood's web site, but I have not received a response to the problem,
only an acknowledgement they received my message.

Thank You in advance, John N3AOF





factory reset procedure?
stuck switch?
bad ribbon/contact ?

Kenwood TM-V71A Transceiver Locked Up in Cross Band Repeater Mode
 

On Tue, 10 Sep 2013 09:45:31 -0400, wrote:

Hi,

I have a Kenwood TM-V71A 144/440mhz transceiver that is "locked up" in
CBR ("Cross Band Repeater") mode. Note: In this mode, the Kenwood radio
"acts" like a repeater.
SNIP

PROBLEM SOLVED:

I just received an email from Kenwood and was told to try holding the
"REV" button (alternate to "TONE" button), then turn on the power.
By golly, it worked!!!

John

Kenwood TM-V71A Transceiver Locked Up in Cross Band RepeaterMode
 

On 11/09/2013 15:15, wrote:
On Tue, 10 Sep 2013 09:45:31 -0400, wrote:

Hi,

I have a Kenwood TM-V71A 144/440mhz transceiver that is "locked up" in
CBR ("Cross Band Repeater") mode. Note: In this mode, the Kenwood radio
"acts" like a repeater.
SNIP

PROBLEM SOLVED:

I just received an email from Kenwood and was told to try holding the
"REV" button (alternate to "TONE" button), then turn on the power.
By golly, it worked!!!

John



so that nugget is now out in wwwland
factory reset different to "full reset" ?

Kenwood TM-V71A Transceiver Locked Up in Cross Band RepeaterMode
 

On 09/11/2013 07:15 AM, wrote:
On Tue, 10 Sep 2013 09:45:31 -0400, wrote:

Hi,

I have a Kenwood TM-V71A 144/440mhz transceiver that is "locked up" in
CBR ("Cross Band Repeater") mode. Note: In this mode, the Kenwood radio
"acts" like a repeater.
SNIP

PROBLEM SOLVED:

I just received an email from Kenwood and was told to try holding the
"REV" button (alternate to "TONE" button), then turn on the power.
By golly, it worked!!!

John


Youtube could have told you that.

Kenwood TM-V71A Transceiver Locked Up in Cross Band RepeaterMode
 

On 09/11/2013 07:20 AM, N_Cook wrote:
On 11/09/2013 15:15, wrote:
On Tue, 10 Sep 2013 09:45:31 -0400, wrote:

Hi,

I have a Kenwood TM-V71A 144/440mhz transceiver that is "locked
up" in
CBR ("Cross Band Repeater") mode. Note: In this mode, the Kenwood radio
"acts" like a repeater.
SNIP

PROBLEM SOLVED:

I just received an email from Kenwood and was told to try
holding the
"REV" button (alternate to "TONE" button), then turn on the power.
By golly, it worked!!!

John



so that nugget is now out in wwwland
factory reset different to "full reset" ?

Not a reset, just a change of mode. Cross Band Repeater locks all the
controls, for obvious reasons.