Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to sci.electronics.repair
|
|||
|
|||
Roland Cube distortion
On "octave bass" setting only , which of course is the one used.
A sort of auto-wah effect at the flanger rate but with the effects controls turned to off position. Alternate peaks of a 200 Hz input signal are attenuated. Thats with the gain pot at about 60 percent but above 70 percent then a cross-over type distortion moves into the attenuated traces as well. No response to twizzle stick or ribbon connector movement,SM IC pushing etc. Not fully taken apart yet , but any ideas ? -- Diverse Devices, Southampton, England electronic hints and repair briefs , schematics/manuals list on http://home.graffiti.net/diverse:graffiti.net/ |
#2
Posted to sci.electronics.repair
|
|||
|
|||
Roland Cube distortion
N Cook wrote in message
... On "octave bass" setting only , which of course is the one used. A sort of auto-wah effect at the flanger rate but with the effects controls turned to off position. Alternate peaks of a 200 Hz input signal are attenuated. Thats with the gain pot at about 60 percent but above 70 percent then a cross-over type distortion moves into the attenuated traces as well. No response to twizzle stick or ribbon connector movement,SM IC pushing etc. Not fully taken apart yet , but any ideas ? -- Diverse Devices, Southampton, England electronic hints and repair briefs , schematics/manuals list on http://home.graffiti.net/diverse:graffiti.net/ Should have said Roland Cube 30. Looks now more like a no goer. Any known problems with the system of pots (nothing ohmically wrong) turning to 0 ohm to switch off digital effects?, the LED goes out but it is as though the micro doesn't know that. Good sine signals through both sides of dual opamps IC1 and IC2, distorted signal at both sides of same IC , IC3. +/-8V supplies to the opamps good and clean as is 3.3V rail for the following. Tracing signal back it seems to go to IC4 an AKM4552VT no data found but AKM4550VT is an Asahi ADC/DAC of same 0.65mm format 16 pin but slightly different pinning. Good sine in but distorted signal out so presumably the digital processing is buggered somehow. I doubt if a schematic would help if its a corrupt micro. -- Diverse Devices, Southampton, England electronic hints and repair briefs , schematics/manuals list on http://home.graffiti.net/diverse:graffiti.net/ |
#3
Posted to sci.electronics.repair
|
|||
|
|||
Roland Cube distortion
N Cook wrote in message
... N Cook wrote in message ... On "octave bass" setting only , which of course is the one used. A sort of auto-wah effect at the flanger rate but with the effects controls turned to off position. Alternate peaks of a 200 Hz input signal are attenuated. Thats with the gain pot at about 60 percent but above 70 percent then a cross-over type distortion moves into the attenuated traces as well. No response to twizzle stick or ribbon connector movement,SM IC pushing etc. Not fully taken apart yet , but any ideas ? -- Diverse Devices, Southampton, England electronic hints and repair briefs , schematics/manuals list on http://home.graffiti.net/diverse:graffiti.net/ Should have said Roland Cube 30. Looks now more like a no goer. Any known problems with the system of pots (nothing ohmically wrong) turning to 0 ohm to switch off digital effects?, the LED goes out but it is as though the micro doesn't know that. Good sine signals through both sides of dual opamps IC1 and IC2, distorted signal at both sides of same IC , IC3. +/-8V supplies to the opamps good and clean as is 3.3V rail for the following. Tracing signal back it seems to go to IC4 an AKM4552VT no data found but AKM4550VT is an Asahi ADC/DAC of same 0.65mm format 16 pin but slightly different pinning. Good sine in but distorted signal out so presumably the digital processing is buggered somehow. I doubt if a schematic would help if its a corrupt micro. -- Diverse Devices, Southampton, England electronic hints and repair briefs , schematics/manuals list on http://home.graffiti.net/diverse:graffiti.net/ Looks like a pot problem Tracing the lines back to the 48 pin IC8 Roland chip then pin 22 goes to the LED and the wiper of the effects pot goes to pin 4 via 100R.I don't understand why with a few ohms left on the pot at "zero" the LED goes out but the effect does not stop. Rather than trying to change the sub miniature pot I'll add in a switch to ground on the pin4 side of the 100R, as the owner never uses the effects anyway. The crossover problem was not realising I was on the wrong sig gen attenuator setting. -- Diverse Devices, Southampton, England electronic hints and repair briefs , schematics/manuals list on http://home.graffiti.net/diverse:graffiti.net/ |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Roland Cube 30 Bass or: Putting a sock in it. | Electronics Repair | |||
ice macker crushed the cube and dot fall cube | Home Repair | |||
Zip drive in Roland VS-840 | Electronics Repair | |||
Roland MC505 - LCD PWB delaminated. Need Help | Electronics Repair | |||
Schematics for Roland TR-505 | Electronics Repair |