Hi, I am new to this so any help would be appreciated. I have a circuit
with relay, some resistors and capacitors, diodes and a transistor. The
circuit has problem as the relay doesnt click and the dehumidifier
doesnt start. I tried the relay on this circuit on another one and the
relay works fine, so its not the relay that has issue. Diode seem to be
ok they conduct one way (could there still be some potential problem
even though they show working ?)

I am not sure how to test the other components, I tried testing the
resistors and they all seem fine and show me a value on digital
multimeter. How do you test all the components on a circuit, i read it
suggested that the components be tested outside the circuit, certainly
with so many components they cant all be taken out of the board and
tested ? what else should I check and what could be wrong here...

thanks

On 20 Oct 2006 08:51:43 -0700, wrote:

Hi, I am new to this so any help would be appreciated. I have a circuit
with relay, some resistors and capacitors, diodes and a transistor. The
circuit has problem as the relay doesnt click and the dehumidifier
doesnt start. I tried the relay on this circuit on another one and the
relay works fine, so its not the relay that has issue. Diode seem to be
ok they conduct one way (could there still be some potential problem
even though they show working ?)

I am not sure how to test the other components, I tried testing the
resistors and they all seem fine and show me a value on digital
multimeter. How do you test all the components on a circuit, i read it
suggested that the components be tested outside the circuit, certainly
with so many components they cant all be taken out of the board and
tested ? what else should I check and what could be wrong here...

thanks

Humidity sensors are difficult to check, as the sensor element is
often a capcitive device that is driven by an AC voltage which is
generated on the controller board. Without an oscilloscope to check
for the AC waveform and/or a service document that specifies the
expected voltages, this is hard to test.

This board has no humidity sensor. that is external and a mechanical
one. what this board does or is suppose to do when you turn the knob on
humidistat this waits for a couple of mins and then relay clicks and
the dehumidifier starts. this doesnt click at all. I moved the relay to
another board and tested and that is good. any other reference material
or site/forum to get additional help would be appreciated.



John wrote:
On 20 Oct 2006 08:51:43 -0700, wrote:

Hi, I am new to this so any help would be appreciated. I have a circuit
with relay, some resistors and capacitors, diodes and a transistor. The
circuit has problem as the relay doesnt click and the dehumidifier
doesnt start. I tried the relay on this circuit on another one and the
relay works fine, so its not the relay that has issue. Diode seem to be
ok they conduct one way (could there still be some potential problem
even though they show working ?)

I am not sure how to test the other components, I tried testing the
resistors and they all seem fine and show me a value on digital
multimeter. How do you test all the components on a circuit, i read it
suggested that the components be tested outside the circuit, certainly
with so many components they cant all be taken out of the board and
tested ? what else should I check and what could be wrong here...

thanks

Humidity sensors are difficult to check, as the sensor element is
often a capcitive device that is driven by an AC voltage which is
generated on the controller board. Without an oscilloscope to check
for the AC waveform and/or a service document that specifies the
expected voltages, this is hard to test.

wrote in message
ups.com...

This board has no humidity sensor. that is external and a mechanical
one. what this board does or is suppose to do when you turn the knob on
humidistat this waits for a couple of mins and then relay clicks and
the dehumidifier starts. this doesnt click at all. I moved the relay to
another board and tested and that is good. any other reference material
or site/forum to get additional help would be appreciated.

Then it is a time delay, designed to prevent quick restart of the
compressor. You need a circuit diagram, service manual or several years of
experience to repair it.

Homer J Simpson wrote:
wrote in message
ups.com...

This board has no humidity sensor. that is external and a mechanical
one. what this board does or is suppose to do when you turn the knob on
humidistat this waits for a couple of mins and then relay clicks and
the dehumidifier starts. this doesnt click at all. I moved the relay to
another board and tested and that is good. any other reference material
or site/forum to get additional help would be appreciated.

Then it is a time delay, designed to prevent quick restart of the
compressor. You need a circuit diagram, service manual or several years of
experience to repair it.

Yes, or if youre lucky posting the cct diag for us to see might get you
somewhere. No circuit, forget it.


NT

Homer J Simpson wrote:

Then it is a time delay, designed to prevent quick restart of the
compressor. You need a circuit diagram, service manual or several years of
experience to repair it.

Yes, or if youre lucky posting the cct diag for us to see might get you
somewhere. No circuit, forget it.

Forgot to mention, if its a time delay you could likely run the system
without it, if necessary.


NT

wrote in message
ps.com...

Forgot to mention, if its a time delay you could likely run the system
without it, if necessary.

If you replace it with a manual switch and don't quickly restart the
compressor. But even then there may be an anti freeze or overflow switch.