Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
|
#2
Posted to sci.electronics.repair
|
|||
|
|||
UPDATE: RCA TV 27F530T, ch ITC008KC3 Width Problem
Quite happy to help out! That's what this group is for. Rono.
Brad wrote: Hi, Thanks to Rono and Art for your help. I soldered the three wires (1 blue and 2 brown) direct after I removed the connectors and pins. That solved the problem. Note: I also soldered some other joints on the PCC board that looked like they could use more solder. Brad On Sun, 26 Mar 2006 05:48:09 GMT, (Jason D.) wrote: On Sat, 25 Mar 2006 17:07:26 -0500, "Art" wrote: Also, if attempts to repair the PCC board are a quandry, RCA did supply the complete item as a replacment part. I'm sure that someone with Parts Finder may give you the P/N for the whole PCC Board. "Rono" wrote in message groups.com... On larger sets with the same chassis, you have to solder the connectors going from the main board to the EW pincushion board. You MAY have to cut the wires, & solder them directly to the board. The wires are blue, & also brown. Otherwise you MAY have a failing part on the mainboard, or on the little pincushion board. The RCA/GE B2B site is down, the last two days so I can't give you any more info. Hope this helps. Dani. Do this asap or the HOT fails, this is diffcult one to trace, it is the 3 thick (two brown and blue) wires harness with 2 connectors the problem, connectors are either milky clear or black. This goes between chassis just by the fly and the small pincushion board. Cut connectors off, pull pins (melt the solder while doing so,) and solder these wires in directly. This fixes the problem. Cheers, Wizard ORIGINAL POST: On Sat, 25 Mar 2006 19:39:33 GMT, (Brad) wrote: Hi, An RCA TV, model 27F530T, ch ITC008KC3 (mfg. 11/03) came into my service shop with a width problem. There is a little too much width (overscan), and the width is constantly fluctuating a little. I do not have a service manual for this model TV. Anyone run into a problem like this with this or a similar model? Thanks in advance, Brad Before you type your password, credit card number, etc., be sure there is no active key logger (spyware) in your PC. |
#3
Posted to sci.electronics.repair
|
|||
|
|||
UPDATE: RCA TV 27F530T, ch ITC008KC3 Width Problem
Good Job, Congrats!
"Geri" wrote in message oups.com... Quite happy to help out! That's what this group is for. Rono. Brad wrote: Hi, Thanks to Rono and Art for your help. I soldered the three wires (1 blue and 2 brown) direct after I removed the connectors and pins. That solved the problem. Note: I also soldered some other joints on the PCC board that looked like they could use more solder. Brad On Sun, 26 Mar 2006 05:48:09 GMT, (Jason D.) wrote: On Sat, 25 Mar 2006 17:07:26 -0500, "Art" wrote: Also, if attempts to repair the PCC board are a quandry, RCA did supply the complete item as a replacment part. I'm sure that someone with Parts Finder may give you the P/N for the whole PCC Board. "Rono" wrote in message groups.com... On larger sets with the same chassis, you have to solder the connectors going from the main board to the EW pincushion board. You MAY have to cut the wires, & solder them directly to the board. The wires are blue, & also brown. Otherwise you MAY have a failing part on the mainboard, or on the little pincushion board. The RCA/GE B2B site is down, the last two days so I can't give you any more info. Hope this helps. Dani. Do this asap or the HOT fails, this is diffcult one to trace, it is the 3 thick (two brown and blue) wires harness with 2 connectors the problem, connectors are either milky clear or black. This goes between chassis just by the fly and the small pincushion board. Cut connectors off, pull pins (melt the solder while doing so,) and solder these wires in directly. This fixes the problem. Cheers, Wizard ORIGINAL POST: On Sat, 25 Mar 2006 19:39:33 GMT, (Brad) wrote: Hi, An RCA TV, model 27F530T, ch ITC008KC3 (mfg. 11/03) came into my service shop with a width problem. There is a little too much width (overscan), and the width is constantly fluctuating a little. I do not have a service manual for this model TV. Anyone run into a problem like this with this or a similar model? Thanks in advance, Brad Before you type your password, credit card number, etc., be sure there is no active key logger (spyware) in your PC. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Sad update on P61310JX4 blanking out problem. | Electronics Repair | |||
Update: Toshiba TV CE27C15, ch TAC9345 Sound Balance Problem | Electronics Repair | |||
Printed Board update, problem solved for now | Woodturning | |||
Printed Board update, problem solved for now | Woodworking |