On 21/08/2020 19:47:15, Jim GM4 DHJ ... wrote:
On 21/08/2020 18:23, Fredxx wrote:
On 21/08/2020 16:38:28, Jim GM4 DHJ ... wrote:
On 16/08/2020 18:17, Jim GM4DHJ ... wrote:
On 16/08/2020 18:13, Jim GM4DHJ ... wrote:
On 16/08/2020 11:09, Fredxx wrote:
On 15/08/2020 23:28:45, Jim GM4DHJ ... wrote:
On 15/08/2020 23:22, Jim GM4DHJ ... wrote:
On 15/08/2020 21:35, Fredxx wrote:
On 09/08/2020 12:48:50, Jim GM4DHJ ... wrote:
The boiler at the van here has started acting up
today.....sometimes when you turn the hot water off the flame
stays on and you can hear it boiling the now static water with
all sorts of boiling and gurgling and rattling
noises......must be the flow sensor not turning the boiler
flame off.....The problem is intermittant but a pain to listen
to and I am sure it is not doing the boiler any good....any
ideas? .....before I get a man in
Given you don't seem able to lookup up its flow switch assembly
you will definitely need to get someone in to replace this or
diagnose the problem.
https://lmgtfy.com/?q=worcester+24i+parts
had it apart couldn't find it smart arse .....
https://ibb.co/KDQddmF
https://ibb.co/BVT6vxw
https://ibb.co/zS8xB3r
https://ibb.co/gjDXFVC
https://ibb.co/tz6KsLJ
https://ibb.co/7vMGKtD
https://ibb.co/wgMdcrQ
https://ibb.co/Lg2K7HN
https://ibb.co/BykTskr
https://ibb.co/b6JpchH
https://ibb.co/0GRFZYw
https://ibb.co/gMBrbsC
https://ibb.co/wRzqWcB
https://ibb.co/yytjmLv
https://ibb.co/sHr1vJY
https://ibb.co/S6v6MMV
https://ibb.co/sjGVky2
https://ibb.co/qRWpS2Z
https://ibb.co/KDDZgWT
https://ibb.co/FB6CbTK
https://ibb.co/zF0FG1D
so...where is it?
If you can't recognise it then definitely get a man in.
going to....
The part is most likely:
Â*Â* https://ibb.co/gMBrbsC
nah that is some kind of temperature sensor clamped around the pipe
Assuming you are taking a photo from below?
Â*Â*https://www.plumbase.co.uk/flow-swit...000043-3529181
that will be it but I cant find it........
As another poster has said I would check using a meter before
replacing.
I would if I could find it.....
oh wait... the thing on the right of the photo...yes that will be
it.....
just been back down because the gas safe man couldn't come until next
week...took the valve off ...dead easy just got a exact replacement
for £41 at heat spares Govan... fitting it tomorrow.....wish me luck
Have you inspected the unit? Does it use a rotating vane to check for
water flow?
Or is flow sensed by pressure difference in which case there will be 2
holes either side. One could be blocked.
they seem to have a bit of plastic inside which is hinged and I assume
makes a contact to turn on the flame when the water is flowing and
breaks when the flow stops.....there are four screws on the unit so I
will take the old one apart tomorrow ...
If it now moves freely then refit it and it may well work trouble free
for a few more years.
Why can't you test the contacts with a multimeter? You do have one?