Stormin' Norman wrote in
:

On 29 Jun 2017 17:44:12 GMT, KenK wrote:

Stormin' Norman wrote in
m:

On 28 Jun 2017 17:55:21 GMT, KenK wrote:

Stormin' Norman wrote in
m:

On 28 Jun 2017 16:34:59 GMT, KenK wrote:

Stormin' Norman wrote in
news:h7k7lc1hh7co2oe9jia5mkr87qs7vfhk22@4ax. com:

On 28 Jun 2017 13:56:37 GMT, KenK wrote:

I have three phones - two in the house, one in a separate
office building. The two in my home don't work. I traced
signal to the box and barrier strips where the line is split
and goes to the two phones. Signal ok at that point. Phone in
kichen has signal from the splitter to a connector that goes
between bare phone line and female phone connector. Have
signal there where line is connected with an old repairman's
test phone with alligator clips. Phone doesn't work. Tried the
other phone. Doesn't work. Tried a spare phone that works
IIRC. Doesn't work. Only place for a problem is between bare
line connection and female connector. Not likely but that is
what I find. Afraid to test with working phone - don't want to
damage my only working phone by messing with connection or
plugging in a possibly bad phone. The other splitter line goes
to an answering machine. It doesn't answer the phone if I call
it on my cell. No convenient place there to use alligator clip
repair phone - all phone line standard connectors.

Doesn't make any sense.

Any theories to try?

TIA

Are you saying you have three, wired, extension phones all on
the same number? The one in the out building works but the
other two do not?

Yes.

If the above describes the problem, take one of the phones that
doesn't work and, as a test, connect it to the jack in the out
building. If the phone works when connected to that jack, then
you have a wiring problem in the house.

As I said, I'm reluctant to do that. I hate to mess with the only
phone line that works. Also, it's my internet connection line. I
don't think it's a phone, or at least one of them, where the
answering machine doesn't work either. After all, an answering
machine is just a specialized phone.


Take the above working phone and start by connecting it to the
jacks in the house from the beginning of the circuit to the end.
You should be able to isolate the two points between where the
circuit has gone dead.

I tried that. Doesn't work as far back towards the splitter as I
can get. Odd that both sides of the splitter should fail, but
there is a signal in and out of the splitter. The ho,emade
'splitter' is a metal box with a barrier circuit strip. The line
from the phone company box goes to two screws on the strip where
it branches to four other screws on the barrier strip, which in
turn feed the lines to the two phones. All those screw pairs in
the splitter show a dial tone. This is about 20 - 30 years old and
has worked with no problem up until now.

Odds are, you have a bad splitter or a loose / broken wire at a
jack. You could also have a defective jack.

It would have to be two jacks as there are none before the
splitter. Seems unlikely but you never know.

You can use your test set if you like, but you are not going to
damage a regular telephone by plugging it into a miss wired
jack.

Other questions?

It is a simple two wire system. You have a loose / corroded /
broken wire / connection somewhere in the circuit.

I would start with the home made splitter and inspect / tighten /
clean all of the connections.

Also, your description doesn't make a lot of sense, if the twisted
pair from the street is going to your home made splitter, and then
branches off to two extension, just how is the third extension in
the out building connected to the circuit?


There are two lines leaving the telephone company's box - one to the
splitter for the two phones in my home, the other a single line to
my 'office'. The signal successfully, according to my
alligator-clipped phone, gets to the splitter. The problem is after
that point, but that's where I get confused. If signal is ok when
arriving at the splitter, how could a problem after the splitter on
one output affect the other splitter output? Or just coincidence
that two problems arose at the same time? Hard to believe. I'm more
confused than usual. Or maybe the alligator phone is misleading me
somehow?

You need to unscrew the terminals in the splitter and inspect those
wires, it is really quite simple.

From what you are writing, it appears you really don't know if the
signal is "leaving" the splitter, you simply know that the signal is
present in the splitter.

If you post a picture of the internals of the splitter, it might
help me help you.

Stormin' et al:

Got a chance to work on it yesterday afternoon - in the 114 heat!

Got both phones working. One phone turned out to be bad. Replaced it
with an amcient spare. Working now. The other turned out to be a bad
splitter- to-phone line. Replaced it outside on the ground. Will bury
it or put it under the home when the weather cools off this fall. Now
both phones work but both really should be replacrd.

It always pays to test the questionable devices, as I had suggested.

Glad you resolved your problem. You might save yourself some
aggravation and purchase a multi-handset cordless phone. Connect the
base station to your working jack and forget about repairing the other
jacks and wiring. The cordless phone are quite reliable, just keep
handy one working corded phone in the event of power failure.


I'll take a look at them at Walmart when I go grocery shopping Saturday,
Thanks for the suggestion.


--
I love a good meal! That's why I don't cook.