"Ed Huntress" wrote in message
...
"stu" no where just yet wrote in message
...
"Ed Huntress" wrote in message
...
"Ed Huntress" wrote in message news:...
wrote in message
...
On Sun, 14 Mar 2010 00:55:03 +1100, "stu" no where just yet
wrote:
wrote in message
news:cu3np5la85p48d0vchp58tos9do4fun5me@4ax. com...
On Sat, 13 Mar 2010 20:55:17 +1100, "stu" no where just yet
wrote:
I've just posted a picture in http://www.metalworking.com/Dropbox
called
"stusplate"(is it the done thing to put a direct link here?)
As you can see from the reflection of newpaper, the surface has a
very
fine
finish like no surface plate I have ever seen. It comes in a felt
lined
lockable box. Does anyone have any idea what this sort of plate is?
Could be an optical flat. Your jpg doesn't show the size.
Inspection grade optical flats are typically 5 or 6" dia and
polished flat to within a fraction of the wavelength of green
light.
Jim
So that would be pretty flat then lol
I have two, one is 170mm(7inches) x 35mm(1.5inches) thick. The other
is
220mm(9inches) x 35mm(1.5inches)they are labeled "precison plate"
I thought about optical flats but I thought they were made from
glass?(although I'm not even sure I've ever seen an optical flat)
Most optical flats are glass or quartz. I have a 6"dia x 1/2"
glass flat. Although your flats are opaque, bearing in mind the
polish, the thickness and the careful packaging, I still think
they are likely to be flat to optical precision standard
Jim.
Stu has a couple of toolmaker's flats. They're made with a surface that
allows a gage block to be wrung to the surface, so that clamps aren't
needed. It's frequently used in gage labs for qualifying and certifying
instruments. Standard sizes are 2" and 4", so Stu's are something
pretty special. I've seen them that big, though, in Mitutoyo's
qualification lab.
If you keep that surface scratch-free, there's no better way to set up
a stack of gage blocks to extreme, certifiable, transferable accuracy.
--
Ed Huntress
BTW, I should mention that their original purpose, which is now about 30
or 40 years out of date, was to qualify custom gages that were used in
production manufacturing -- go/no-go snap gages and so on.
--
Ed Huntress
Thanks Ed (and others)
There are some light scratches in the small one, just behind the person
it the photo. I didn't do a very good job cleaning the block as I wasn't
sure what to use. I'm yet to clean the large one, I'll try to get onto it
this evening, but what to use? I'm guessing "kero and a rag" aren't the
done thing.
Kero and a rag isn't bad at all. Don't use anything the least bit abrasive
or corrosive to steel. No Windex. Then lightly oil it with a rag and put
it away. Wipe the oil off before using. If you're going to try wringing
gage blocks against them, clean with a solvent on the working surface,
really well, first. Paint thinner should do it.
I believe you are right about the "production manufacturing ", they have
a name plate from a wire company where I am guessing they were used, but
they have no other name on them.
I'm try and get some more info on here tonight.
thanks again
Stu
You're welcome, Stu. They're interesting tools and they don't take up much
room. With scratches, you probably won't get much for them, so you'd might
as well keep them.
Do you have a set of gage blocks?
--
Ed Huntress
I've uploaded a couple of pictures of the large plate after a quick clean
wipe of kero.
http://www.metalworking.com/Dropbox/stusplatelarge.jpg
http://www.metalworking.com/Dropbox/stusplatelargeb.jpg
as you can see the isnt as good as the small one. I would think that it is
still plenty good enough for me. It will be nice to have something "flat" in
the shed, even if it is a little over the top.
I dont have gauge blocks yet although I am keeping an eye out for some, I
cant really think of an excuse to buy a new set.