On Thu, 09 Feb 2006 19:08:25 -0500, mm
wrote:

On 9 Feb 2006 04:26:35 -0800, "
wrote:

My Washers spray fresh water on the clothes during the spin cycle. I
believe its to minimize wrinkling but dont really know. first time I

It's to rinse the clothes a few extra times, when most of the wash
water is rinsed away so the tub doesn't have to be filled again.

After that part of the spin cycle is done, the second half of the spin
cycle does nothing but remove water.

FTR, I think this has been the standard way for more than 50 years,
certainly more than 30.

OK, I have a weird problem though. When that injector is in place,
the water drips out of the holes in the side of it. But here's the
weird part. I have a well. My pressure switch is set to go ON at
30lbs, and OFF at 50lbs +/- a few pounds.
Whenever my pump kicks in, thats when the water squirts out that darn
thing. I took it apart and soaked it in LimeAway to be sure it was
clean. It still does that, and nothing is cracked. The machine is
inside the house, not a a cement floor and if i let it drip my floor
is going to rot out. That's why I replaced it with a standard barbed
fitting. The machine still rinses, the water just pours into the tub
harder, rather than a finer spray. What that matters, I dont know,
because I do not see any difference in the end result. However, I
stopped the water on the floor and also the machine initially fills in
2 minutes instead of 5, so the laundry gets done faster.

I should note, this machine was originally used in the city where the
water pressure is 70 to 80 lbs. Go figure ????
It just seems that the pump makes it go bonkers. I did remove the
screens from the fill valve because they were clogged with lime, and I
replaced them with the hose-washer filters that go on the end of the
supply hoses, so in the end, I have the same thing. It just seems to
not want to function on my well pump without dripping.....

I tried to call Maytag. That was a waste of time. First they wanted
to know so much personal information, just short of asking about my
sex life. I finally told them I am not placing an order and they dont
need anything beyond my name and zipcode. Because I refused to give
them my (unlisted) phone number, they told me they could not assist me
without my answering their questions. I finally gave them all they
wanted (just not the correct phone number and address). Ten minutes
of that annoyance, they finally came back and told me that there is no
such model number. I took the phone behind the machine, put on my
reading glasses and told them exactly every letter and number on the
ID tag. They told me no such model exists. About that time I got a
tad bit ****ed and said "this IS a Maytag, I have given you every
possible number and letter on the ID tag, what the heck more do you
want?". That's when they asked me the age of the machine, and I told
them I am guessing about 30 years old. Thats when they told me that
they do not keep records older than 5 or 6 years.

Why the F**k they couldn't tell me that right from the start, and not
waste a half hour of my time....

What really ****ed me off, is that after all of this, the person asked
me why the phone number I gave is different from the one my caller ID
showed. I think the whole time they were checking on my identity
rather than even bothering to look for the model of my machine. Even
more strange, Today I got a telemarketing call selling appliances.
Like I said, my number is UNLISTED, and I an on the DO NOT CALL list,
and have not gotten a telemarketing call in at least a year.
I was certain to threaten the telemarketer for not checking to see if
I am on the DNC list, and told them if they call again, they pay the
fine.

After this incident, I will be sure to never buy a new appliance from
Maytag. (Not that I'd want one, from looking on the web, it seems
their newer machines are really poorly made and have lots of recalls
and problems). My machine may be 25 to 30 years old, but it's built
like a battleship. I found that out when I had to move it up a flight
of stairs. There's a good 300 lbs or more of steel...

Mark



saw it thought the fill valve or timer were bad.

have to trip out the door switch to see this.

of course mine is a top loader


Remove NOPSAM to email me. Please let
me know if you have posted also.