Tablesaw question - followup
Well, I got the old flex drive Sears tablesaw fully adjusted today and cut
some wood with it. I managed to reduce the runout of the arbor to about 1/4 that of the blade itself using a cheap dial indicator that I bought from Harbor Freight for, IIRC, $13.00. I drilled a hole in the end of a 1X3 and mounted the dial indicator to it with a pan head screw. My saw has a hold-down on the miter gauge so I clamped the board/dial indicator assembly to it and -- using the marked tooth technique -- managed to reduce the arbor error to .003 inch. My first cut was another 1X3 and was not perfectly square but off a fraction of a degree. It turns out that the stops on the miter gauge are not perfectly adjusted (yet) so I held my speed square against the fence and the miter gauge and tightened it down. The next cut produced an end that rivalled that of my very-well-adjusted power miter box. The small off-cut stayed right where it stopped and was not kicked back by the spinning blade, nor did the end of the oak stock scorch. I had previously adjusted the rip fence to the best of my ability and one of my questions (posted 11/4/04) concerned acceptable error for a fence. It turns out that mine has a total error of about .015 inch, .007 in one direction and about .008 in the other. Some have said that's an acceptable number. I haven't tried using the fence yet...that'll be next. Oh, I did adjust the ruler on the fence rail and it is now spot on. In a day or two, I'll finish removing the surface rust, which I'm doing with a large, flat block and 220 grit sandpaper. I'll get some rust remover to clean up other parts of the machine and do the table surface with Top Cote or something similar. I also probably need to disassemble the flex drive and lubricate it. It vibrates heavily when starting but then settles down and runs smoothly and quietly. I'm pretty pleased with the old girl so far. Once I've finished the restoration I'll make some jigs like a crosscut sled, etc. Then it'll be time to do some real work... |
Chuck Hoffman wrote:
rivalled that of my very-well-adjusted power miter box. The small off-cut stayed right where it stopped and was not kicked back by the spinning blade, nor did the end of the oak stock scorch. Sweet innit? The only down side of having a dial indicator, and then seeing how much of a difference it makes lining up something REALLLLLLLY close, is that you become a precision freak. It's easy to get hung up on precision. -- Michael McIntyre ---- Silvan Linux fanatic, and certified Geek; registered Linux user #243621 http://www.geocities.com/Paris/Rue/5407/ http://rosegarden.sourceforge.net/tutorial/ |
Aye, sweet it is, mate.
My cheap dial indicator probably does every bit as good a job of aligning my tablesaw as the precision ground flat plate and expensive dial indicator advertised in the US woodworking mags. "Silvan" wrote in message ... Chuck Hoffman wrote: rivalled that of my very-well-adjusted power miter box. The small off-cut stayed right where it stopped and was not kicked back by the spinning blade, nor did the end of the oak stock scorch. Sweet innit? The only down side of having a dial indicator, and then seeing how much of a difference it makes lining up something REALLLLLLLY close, is that you become a precision freak. It's easy to get hung up on precision. -- Michael McIntyre ---- Silvan Linux fanatic, and certified Geek; registered Linux user #243621 http://www.geocities.com/Paris/Rue/5407/ http://rosegarden.sourceforge.net/tutorial/ |
On Sun, 07 Nov 2004 01:24:03 GMT, "Chuck Hoffman"
wrote: Aye, sweet it is, mate. My cheap dial indicator probably does every bit as good a job of aligning my tablesaw as the precision ground flat plate and expensive dial indicator advertised in the US woodworking mags. cheap dial indicators are plenty good enough for setting up woodworking equipment. the flat plate blade replacement things are sorta stupid, if you ask me. |
Chuck Hoffman wrote:
Aye, sweet it is, mate. My cheap dial indicator probably does every bit as good a job of aligning my tablesaw as the precision ground flat plate and expensive dial indicator advertised in the US woodworking mags. 'Course I paid waaaaaaaaaaaaay too much ($30 IIRC) for a Merikun one. -- Michael McIntyre ---- Silvan Linux fanatic, and certified Geek; registered Linux user #243621 http://www.geocities.com/Paris/Rue/5407/ http://rosegarden.sourceforge.net/tutorial/ |
All times are GMT +1. The time now is 03:33 PM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter