holes plugged...
 

I only got one suggestion on that thread, and it wasn't very applicable.
I'm surprised at you, Wreck. Fourteen metric buttloads of political
diatribe, and a real woodworking question went virtually ignored. pout

Well, who needs you anyway! :) I finally came up with a workable plan.

I trued up the (rectangular) holes as best I could, which wound up being
pretty darn close. Then I used my handy dandy dial calipers to measure,
then marked off a slightly oversized rectangle on a piece of scrap 4/4 soft
maple. I left about a 1/4" margin all around the edge.

I measured the thickness of the wood I was plugging with the dial calipers,
then scratched off a line with my, um, ?? marking gauge? I took it over to
my handy dandy new Crapsman contractor's saw, set the fence so that the
working end of the piece would only barely be kissed by the blade, then I
ooched the blade up until it juuuust kissed the line.

I used a combination of fence and miter gauge to hog off all the waste, then
cleaned up the little divots left by the ATB blade with a chisel. Next, I
carefully pared off just enough here and there to get it to be a perfect
fit for the hole. It looked a bit like this at that point:

[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[
[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[
[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[
[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%


Finally, I chucked it up in my electrolytic rust rescue Morgan 10A hunk of
cast iron from hell face vise. I dragged out my #6, my #5, my #4, my #3
and my block plane at one point or another planing the protruding part to a
perfect fit, planing the thick bit down, and then rounding everything over
by hand with the planes, yielding something like this:

/[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[\
/----------------------------------------------\
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%

Then I glued the sucker in the hole for a perfect fit. Backed up by that
flange integrated into the wood, it should be plenty strong enough to
anchor a screw for a latch.

Lather, rinse, repeat. It took about three hours to make two of these
little parts. All of it was spent working too. The last time I used any
of these tools, I put them away sharp, so I didn't have any
sharpening/fiddling to do.

Pretty nice little afternoon jaunt, and I figured it out all by my widdle
self, so nyah.

--
Michael McIntyre ---- Silvan
Linux fanatic, and certified Geek; registered Linux user #243621
http://www.geocities.com/Paris/Rue/5407/
http://rosegarden.sourceforge.net/tutorial/

On Wed, 03 Nov 2004 20:56:23 -0500, Silvan
wrote:
I might help a bit to give a hint about the original post...

probably just me and my alcohol level, but I haven't got a glue what
friggin' hole you fixed...

I only got one suggestion on that thread, and it wasn't very applicable.
I'm surprised at you, Wreck. Fourteen metric buttloads of political
diatribe, and a real woodworking question went virtually ignored. pout

Well, who needs you anyway! :) I finally came up with a workable plan.

I trued up the (rectangular) holes as best I could, which wound up being
pretty darn close. Then I used my handy dandy dial calipers to measure,
then marked off a slightly oversized rectangle on a piece of scrap 4/4 soft
maple. I left about a 1/4" margin all around the edge.

I measured the thickness of the wood I was plugging with the dial calipers,
then scratched off a line with my, um, ?? marking gauge? I took it over to
my handy dandy new Crapsman contractor's saw, set the fence so that the
working end of the piece would only barely be kissed by the blade, then I
ooched the blade up until it juuuust kissed the line.

I used a combination of fence and miter gauge to hog off all the waste, then
cleaned up the little divots left by the ATB blade with a chisel. Next, I
carefully pared off just enough here and there to get it to be a perfect
fit for the hole. It looked a bit like this at that point:

[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[
[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[
[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[
[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%


Finally, I chucked it up in my electrolytic rust rescue Morgan 10A hunk of
cast iron from hell face vise. I dragged out my #6, my #5, my #4, my #3
and my block plane at one point or another planing the protruding part to a
perfect fit, planing the thick bit down, and then rounding everything over
by hand with the planes, yielding something like this:

/[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[[\
/----------------------------------------------\
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%

Then I glued the sucker in the hole for a perfect fit. Backed up by that
flange integrated into the wood, it should be plenty strong enough to
anchor a screw for a latch.

Lather, rinse, repeat. It took about three hours to make two of these
little parts. All of it was spent working too. The last time I used any
of these tools, I put them away sharp, so I didn't have any
sharpening/fiddling to do.

Pretty nice little afternoon jaunt, and I figured it out all by my widdle
self, so nyah.

Good job!
Work at your leisure!