DIYbanter

DIYbanter (https://www.diybanter.com/)
-   Woodworking (https://www.diybanter.com/woodworking/)
-   -   MLCS Track Saw - Worth $160? (https://www.diybanter.com/woodworking/687159-mlcs-track-saw-worth-%24160.html)

DerbyDad03 June 14th 21 04:59 AM

MLCS Track Saw - Worth $160?
 
The MLCS track saw is currently on sale for $160. I know
it's entry level, but it might be good enough for the limited
amount of sheet goods breakdown that I do.

With the soon-to-be-installed inverter in my van, I could
use it to break down sheet goods in the big box parking
lot instead of using my 18V circular saw.

Any thoughts from the track saw experts? Pros, but more
importantly, cons.

https://www.mlcswoodworking.com/shop...track_saw.html

Thanks!

Brian Welch June 14th 21 02:19 PM

MLCS Track Saw - Worth $160?
 
On Sunday, June 13, 2021 at 10:59:08 PM UTC-4, DerbyDad03 wrote:
The MLCS track saw is currently on sale for $160. I know
it's entry level, but it might be good enough for the limited
amount of sheet goods breakdown that I do.

With the soon-to-be-installed inverter in my van, I could
use it to break down sheet goods in the big box parking
lot instead of using my 18V circular saw.

Any thoughts from the track saw experts? Pros, but more
importantly, cons.

https://www.mlcswoodworking.com/shop...track_saw.html

Thanks!

I am not familiar with this system, but I might question the large number of short sections of track, and the ability to keep them perfectly straight...but that's just me...

DerbyDad03 June 14th 21 02:50 PM

MLCS Track Saw - Worth $160?
 
On Monday, June 14, 2021 at 8:19:03 AM UTC-4, Brian Welch wrote:
On Sunday, June 13, 2021 at 10:59:08 PM UTC-4, DerbyDad03 wrote:
The MLCS track saw is currently on sale for $160. I know
it's entry level, but it might be good enough for the limited
amount of sheet goods breakdown that I do.

With the soon-to-be-installed inverter in my van, I could
use it to break down sheet goods in the big box parking
lot instead of using my 18V circular saw.

Any thoughts from the track saw experts? Pros, but more
importantly, cons.

https://www.mlcswoodworking.com/shop...track_saw.html

Thanks!

I am not familiar with this system, but I might question the large number of short sections of track, and the ability to keep them perfectly straight...but that's just me...


I had the same thought.

G Ross[_2_] June 14th 21 06:29 PM

MLCS Track Saw - Worth $160?
 
DerbyDad03 wrote:
The MLCS track saw is currently on sale for $160. I know
it's entry level, but it might be good enough for the limited
amount of sheet goods breakdown that I do.

With the soon-to-be-installed inverter in my van, I could
use it to break down sheet goods in the big box parking
lot instead of using my 18V circular saw.

Any thoughts from the track saw experts? Pros, but more
importantly, cons.

https://www.mlcswoodworking.com/shop...c/store/html/d sdsmarthtml/pages/track_saw.html

Thanks!

I never had a track saw, but I built my own for my "skil" saw. I cut
two pieces of thin plywood or door skin 8 inches wide, One is 4 ft
long, the other 8 ft long. From Lowes I bought two pieces of aluminum
U channel about 1/2 inches deep and wide in 4' and 8' length. These I
fastened 2 inches from the edge of each board using counter-sunk bolts
with the nuts inside the channel, about every foot. I then laid them
on saw horses and ran the skil saw down each one on the wide side and
holding the saw against the aluminum channel.
To cut a marked line I clamp the finished guide with the wide side
against the marked line and clamped the guide to the workpiece using
small C-clamps on the skinny side of the guide, put the saw on the
wide side and saw the cut. Just remember the guide side of the
workpiece is the "saved" side and the other side is the waste piece.
I have used these for years. When not used they hang over the shop
door on nails
through holes drilled in the board.
Total cost much less than for a bought guide.

--
G Ross

DerbyDad03 June 14th 21 07:09 PM

MLCS Track Saw - Worth $160?
 
On Monday, June 14, 2021 at 12:29:48 PM UTC-4, G Ross wrote:
DerbyDad03 wrote:
The MLCS track saw is currently on sale for $160. I know
it's entry level, but it might be good enough for the limited
amount of sheet goods breakdown that I do.

With the soon-to-be-installed inverter in my van, I could
use it to break down sheet goods in the big box parking
lot instead of using my 18V circular saw.

Any thoughts from the track saw experts? Pros, but more
importantly, cons.

https://www.mlcswoodworking.com/shop...c/store/html/d sdsmarthtml/pages/track_saw.html

Thanks!

I never had a track saw, but I built my own for my "skil" saw. I cut
two pieces of thin plywood or door skin 8 inches wide, One is 4 ft
long, the other 8 ft long. From Lowes I bought two pieces of aluminum
U channel about 1/2 inches deep and wide in 4' and 8' length. These I
fastened 2 inches from the edge of each board using counter-sunk bolts
with the nuts inside the channel, about every foot. I then laid them
on saw horses and ran the skil saw down each one on the wide side and
holding the saw against the aluminum channel.
To cut a marked line I clamp the finished guide with the wide side
against the marked line and clamped the guide to the workpiece using
small C-clamps on the skinny side of the guide, put the saw on the
wide side and saw the cut. Just remember the guide side of the
workpiece is the "saved" side and the other side is the waste piece.
I have used these for years. When not used they hang over the shop
door on nails
through holes drilled in the board.
Total cost much less than for a bought guide.

--
G Ross


Yes, I have been using all wood versions of that type of guide for years.

Still curious about the advantages of that inexpensive track saw over
some other options. Place and cut - no clamps - is enticing. The short
pieces of track could make it more convenient than even the 4' guide
is some situations.

Bob D[_2_] June 15th 21 12:55 AM

MLCS Track Saw - Worth $160?
 
On Sunday, June 13, 2021 at 9:59:08 PM UTC-5, DerbyDad03 wrote:
The MLCS track saw is currently on sale for $160. I know
it's entry level, but it might be good enough for the limited
amount of sheet goods breakdown that I do.

With the soon-to-be-installed inverter in my van, I could
use it to break down sheet goods in the big box parking
lot instead of using my 18V circular saw.

Any thoughts from the track saw experts? Pros, but more
importantly, cons.

https://www.mlcswoodworking.com/shop...track_saw.html

Thanks!


I think the tiny motor and 4 1/2" blade will be challenged by anything heavier than 1/2" plywood. I imagine it will cut thicker stock pretty slowly. The smaller blade will be challenged to stay straight when working, even with the track. I think your money would be better spent on a decent full sized circular saw and making your own guide out of wood.

DerbyDad03 June 15th 21 04:13 AM

MLCS Track Saw - Worth $160?
 
On Monday, June 14, 2021 at 6:55:12 PM UTC-4, Bob D wrote:
On Sunday, June 13, 2021 at 9:59:08 PM UTC-5, DerbyDad03 wrote:
The MLCS track saw is currently on sale for $160. I know
it's entry level, but it might be good enough for the limited
amount of sheet goods breakdown that I do.

With the soon-to-be-installed inverter in my van, I could
use it to break down sheet goods in the big box parking
lot instead of using my 18V circular saw.

Any thoughts from the track saw experts? Pros, but more
importantly, cons.

https://www.mlcswoodworking.com/shop...track_saw.html

Thanks!

I think the tiny motor and 4 1/2" blade will be challenged by anything heavier than 1/2" plywood. I imagine it will cut thicker stock pretty slowly. The smaller blade will be challenged to stay straight when working, even with the track. I think your money would be better spent on a decent full sized circular saw and making your own guide out of wood.


I have all the full sized circular saws (corded and battery) that I need. I have homemade
wooden guides, clamp on aluminum guides, 6' levels and all sorts of straight edges.

Thank you for your comments on the motor and blade size of the MLCS track saw. Your
material thickness concerns are noted. I am, however, curious as to how the blade would
wander when the saw is contained within the track. What might cause that to happen?

Bob D[_2_] June 16th 21 12:53 AM

MLCS Track Saw - Worth $160?
 
On Monday, June 14, 2021 at 9:13:52 PM UTC-5, DerbyDad03 wrote:
On Monday, June 14, 2021 at 6:55:12 PM UTC-4, Bob D wrote:
On Sunday, June 13, 2021 at 9:59:08 PM UTC-5, DerbyDad03 wrote:
The MLCS track saw is currently on sale for $160. I know
it's entry level, but it might be good enough for the limited
amount of sheet goods breakdown that I do.

With the soon-to-be-installed inverter in my van, I could
use it to break down sheet goods in the big box parking
lot instead of using my 18V circular saw.

Any thoughts from the track saw experts? Pros, but more
importantly, cons.

https://www.mlcswoodworking.com/shop...track_saw.html

Thanks!

I think the tiny motor and 4 1/2" blade will be challenged by anything heavier than 1/2" plywood. I imagine it will cut thicker stock pretty slowly. The smaller blade will be challenged to stay straight when working, even with the track. I think your money would be better spent on a decent full sized circular saw and making your own guide out of wood.

I have all the full sized circular saws (corded and battery) that I need. I have homemade
wooden guides, clamp on aluminum guides, 6' levels and all sorts of straight edges.

Thank you for your comments on the motor and blade size of the MLCS track saw. Your
material thickness concerns are noted. I am, however, curious as to how the blade would
wander when the saw is contained within the track. What might cause that to happen?


If the blade binds or has a tendency to drift, it can cause the track to slip sideways on the stock. The track is only clamped at each end and it is not an immovable object. A good track saw or circular saw works well, only if the saw cuts cleanly and straight by itself.


All times are GMT +1. The time now is 10:24 AM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter