Protect Metal Surfaces
My woodworking tools get rust.
My tables gets rust. What is the best protective stuff to apply to the table saw, bandsaw table etc. |
Protect Metal Surfaces
On Friday, February 7, 2020 at 3:47:51 PM UTC-5, OtterGuy wrote:
My woodworking tools get rust. My tables gets rust. What is the best protective stuff to apply to the table saw, bandsaw table etc. Apply a dehumidifier to the room. |
Protect Metal Surfaces
OtterGuy writes:
My woodworking tools get rust. My tables gets rust. What is the best protective stuff to apply to the table saw, bandsaw table etc. First, you must determine _why_ they get "rust". If the environment they're stored in is quite humid, get a dehumidifier; surface coatings will likely be insufficient. If someone is setting beer mugs on the table saw, and the condensate is being left behind, don't let them into your shop. If the shop is subject to wide temperature swings and humidity, get some rigid dense foam, cut/glue it to make a cover for the saw (so long as it completely covers the top and is 100% in contact with the top, moisture in the air can't condense on the cold metal surface) Otherwise, a thin coat of paste wax is the most efficacious method. Or you can spend money on various commercial surface coatings, topcoat and dry coat come to mind. |
Protect Metal Surfaces
OtterGuy wrote:
My woodworking tools get rust. My tables gets rust. What is the best protective stuff to apply to the table saw, bandsaw table etc. https://www.homedepot.com/p/100154748 |
Protect Metal Surfaces
My workshop is in the garage so not able to control humidity. I have been told that paste wax does not work. OtterGuy wrote: My woodworking tools get rust. My tables gets rust. What is the best protective stuff to apply to the table saw, bandsaw table etc. |
Protect Metal Surfaces
On 2/7/2020 4:36 PM, Scott Lurndal wrote:
OtterGuy writes: My woodworking tools get rust. My tables gets rust. What is the best protective stuff to apply to the table saw, bandsaw table etc. First, you must determine _why_ they get "rust". If the environment they're stored in is quite humid, get a dehumidifier; surface coatings will likely be insufficient. If someone is setting beer mugs on the table saw, and the condensate is being left behind, don't let them into your shop. If the shop is subject to wide temperature swings and humidity, get some rigid dense foam, cut/glue it to make a cover for the saw (so long as it completely covers the top and is 100% in contact with the top, moisture in the air can't condense on the cold metal surface) Otherwise, a thin coat of paste wax is the most efficacious method. Or you can spend money on various commercial surface coatings, topcoat and dry coat come to mind. I agree with the above. While I can not say my old table saw table looks like it did when it came from the store 50 years ago, my father in law, from whom I inherited the saw, would be proud of the way I have keep it up. Every time I am doodling around the saw I put on a coat of a good car wax. Periodically I use a cleaner polishing compound on the table so the wax does not build up. When rust spots do appear I carefully remove them with a very fine piece of sand paper. Special attention must be made to keep the miter slots clean. I don't use dense foam for a cover, but a piece of 3/8" plywood. In my case the plywood works better because it is less prone to damage. It will not be damaged if a tools falls on the saw. It repels glue, paint, oils or other solvents that would harm the saw, OR penetrate the foam and cause a larger mess. |
Protect Metal Surfaces
On 2/7/2020 5:21 PM, knuttle wrote: On 2/7/2020 4:36 PM, Scott Lurndal wrote: OtterGuy writes: My woodworking tools get rust. My tables gets rust. What is the best protective stuff to apply to the table saw, bandsaw table etc. First, you must determine _why_ they get "rust". If the environment they're stored in is quite humid, get a dehumidifier; surface coatings will likely be insufficient. If someone is setting beer mugs on the table saw, and the condensate is being left behind, don't let them into your shop. If the shop is subject to wide temperature swings and humidity, get some rigid dense foam, cut/glue it to make a cover for the saw (so long as it completely covers the top and is 100% in contact with the top, moisture in the air can't condense on the cold metal surface) Otherwise, a thin coat of paste wax is the most efficacious method. Or you can spend money on various commercial surface coatings, topcoat and dry coat come to mind. I agree with the above. While I can not say myÂ* old table saw table looks like it did when it came from the store 50 years ago, my father in law, from whom I inherited the saw, would be proud of the way I have keep it up. Every time I am doodling around the saw I put on a coat of a good car wax. Periodically I use a cleaner polishing compound on the table so the wax does not build up.Â*Â* When rust spots do appear I carefully remove them with a very fine piece of sand paper. Special attention must be made to keep the miter slots clean. I don't use dense foam for a cover, but a piece of 3/8" plywood. In my case the plywood works better because it is less prone to damage. It will not be damaged if a tools falls on the saw.Â* It repels glue, paint, oils or other solvents that would harm the saw, OR penetrate the foam and cause a larger mess. PS: My work shop is in my garage, and I use the same technique on my handsaw, bandsaw, drill press, metal rulers, t squares, and all tools that are p |
Protect Metal Surfaces
I use Butcher's Bowling Alley Wax. Easy to apply (but with all such products, you reapply as needed) but does not contain any silicone (which causes fish-eye with finishes). Other waxes will do as long as you avoid any that contain silicone (i.e. most "car" waxes) |
Protect Metal Surfaces
knuttle writes:
On 2/7/2020 4:36 PM, Scott Lurndal wrote: OtterGuy writes: My woodworking tools get rust. My tables gets rust. What is the best protective stuff to apply to the table saw, bandsaw table etc. First, you must determine _why_ they get "rust". If the environment they're stored in is quite humid, get a dehumidifier; surface coatings will likely be insufficient. If someone is setting beer mugs on the table saw, and the condensate is being left behind, don't let them into your shop. If the shop is subject to wide temperature swings and humidity, get some rigid dense foam, cut/glue it to make a cover for the saw (so long as it completely covers the top and is 100% in contact with the top, moisture in the air can't condense on the cold metal surface) Otherwise, a thin coat of paste wax is the most efficacious method. Or you can spend money on various commercial surface coatings, topcoat and dry coat come to mind. I agree with the above. While I can not say my old table saw table looks like it did when it came from the store 50 years ago, my father in law, from whom I inherited the saw, would be proud of the way I have keep it up. Every time I am doodling around the saw I put on a coat of a good car wax. Periodically I use a cleaner polishing compound on the table so the wax does not build up. When rust spots do appear I carefully remove them with a very fine piece of sand paper. Watch out for the car waxes that contain silicone - silicone may transfer to work causing finishing defects. |
Protect Metal Surfaces
On Friday, February 7, 2020 at 5:13:49 PM UTC-5, OtterGuy wrote:
My workshop is in the garage so not able to control humidity. I have been told that paste wax does not work. OtterGuy wrote: My woodworking tools get rust. My tables gets rust. What is the best protective stuff to apply to the table saw, bandsaw table etc. Please do not top post in your replies. It is not the standard in this forum. Thanks! I don't know where you heard that paste wax doesn't work. DAGS - will paste wax prevent rust - Just don't use anything that contains silicone. Silicone can transfer to the wood and will affect many finishes. finishes |
Protect Metal Surfaces
On 2/7/2020 3:47 PM, OtterGuy wrote:
My woodworking tools get rust. My tables gets rust. What is the best protective stuff to apply to the table saw, bandsaw table etc. I've had good results with Boeshield T9 https://boeshield.com/ |
Protect Metal Surfaces
On Fri, 7 Feb 2020 21:22:49 -0500, Ed Pawlowski wrote:
On 2/7/2020 3:47 PM, OtterGuy wrote: My woodworking tools get rust. My tables gets rust. What is the best protective stuff to apply to the table saw, bandsaw table etc. I've had good results with Boeshield T9 https://boeshield.com/ As have I. It seems to last forever and works exceptionally well. Just don't put it on too thick or the wood doesn't slide well. |
Protect Metal Surfaces
On Fri, 7 Feb 2020 12:47:46 -0800, OtterGuy
wrote: My woodworking tools get rust. My tables gets rust. What is the best protective stuff to apply to the table saw, bandsaw table etc. BoeShield - or much cheaper and easier to get your paws on - fluid film. |
Protect Metal Surfaces
On Fri, 7 Feb 2020 17:21:24 -0500, knuttle
wrote: On 2/7/2020 4:36 PM, Scott Lurndal wrote: OtterGuy writes: My woodworking tools get rust. My tables gets rust. What is the best protective stuff to apply to the table saw, bandsaw table etc. First, you must determine _why_ they get "rust". If the environment they're stored in is quite humid, get a dehumidifier; surface coatings will likely be insufficient. If someone is setting beer mugs on the table saw, and the condensate is being left behind, don't let them into your shop. If the shop is subject to wide temperature swings and humidity, get some rigid dense foam, cut/glue it to make a cover for the saw (so long as it completely covers the top and is 100% in contact with the top, moisture in the air can't condense on the cold metal surface) Otherwise, a thin coat of paste wax is the most efficacious method. Or you can spend money on various commercial surface coatings, topcoat and dry coat come to mind. I agree with the above. While I can not say my old table saw table looks like it did when it came from the store 50 years ago, my father in law, from whom I inherited the saw, would be proud of the way I have keep it up. Every time I am doodling around the saw I put on a coat of a good car wax. Periodically I use a cleaner polishing compound on the table so the wax does not build up. When rust spots do appear I carefully remove them with a very fine piece of sand paper. Special attention must be made to keep the miter slots clean. I don't use dense foam for a cover, but a piece of 3/8" plywood. In my case the plywood works better because it is less prone to damage. It will not be damaged if a tools falls on the saw. It repels glue, paint, oils or other solvents that would harm the saw, OR penetrate the foam and cause a larger mess. My Myford lathe is in unheated garage and gets a light coating od Fluid Film and it does the job. |
Protect Metal Surfaces
On Fri, 07 Feb 2020 23:58:11 -0500, Clare Snyder
wrote: On Fri, 7 Feb 2020 12:47:46 -0800, OtterGuy wrote: My woodworking tools get rust. My tables gets rust. What is the best protective stuff to apply to the table saw, bandsaw table etc. BoeShield - or much cheaper and easier to get your paws on - fluid film. Boeshield is available at the Borg. Fluid film is about half the cost but isn't available at the local store. A can of Boeshield has lasted me several years. |
Protect Metal Surfaces
On 2/7/2020 2:47 PM, OtterGuy wrote:
My woodworking tools get rust. My tables gets rust. What is the best protective stuff to apply to the table saw, bandsaw table etc. EVERY Location is different. Temp and humidity have a great deal to do with rust. Wax is ok under very controlled environments. The biggest issue is condensing moisture. If you equipment gets cold and is sudden exposed to warm moist air hardly anything will help. I personally use GlideCote. Nothing else has lasted more than a day or two. And GlideCote is not perfect. Actually "USE" is the best for protection assuming there is no condensing moisture. AND FWIW if you actually use your tools your sweat will be an issue. You just have to experiment with what works best for you in your situation. |
Protect Metal Surfaces
On Sat, 8 Feb 2020 11:39:37 -0600, Leon lcb11211@swbelldotnet wrote:
On 2/7/2020 9:40 PM, wrote: On Fri, 7 Feb 2020 21:22:49 -0500, Ed Pawlowski wrote: On 2/7/2020 3:47 PM, OtterGuy wrote: My woodworking tools get rust. My tables gets rust. What is the best protective stuff to apply to the table saw, bandsaw table etc. I've had good results with Boeshield T9 https://boeshield.com/ As have I. It seems to last forever and works exceptionally well. Just don't put it on too thick or the wood doesn't slide well. Lasts for ever. ;~) I tried Boeshield on my brand new, 20 years ago, Jet TS. I had rust the next morning. I put it on my 10YO Unisaur. I think I've re-applied it once since. No rust. Put it my drill press about 8 years ago. I've never re-done it and no rust. I still have the original can. |
Protect Metal Surfaces
On 2/8/2020 1:52 PM, wrote:
On Sat, 8 Feb 2020 11:39:37 -0600, Leon lcb11211@swbelldotnet wrote: On 2/7/2020 9:40 PM, wrote: On Fri, 7 Feb 2020 21:22:49 -0500, Ed Pawlowski wrote: On 2/7/2020 3:47 PM, OtterGuy wrote: My woodworking tools get rust. My tables gets rust. What is the best protective stuff to apply to the table saw, bandsaw table etc. I've had good results with Boeshield T9 https://boeshield.com/ As have I. It seems to last forever and works exceptionally well. Just don't put it on too thick or the wood doesn't slide well. Lasts for ever. ;~) I tried Boeshield on my brand new, 20 years ago, Jet TS. I had rust the next morning. I put it on my 10YO Unisaur. I think I've re-applied it once since. No rust. Put it my drill press about 8 years ago. I've never re-done it and no rust. I still have the original can. No Doubt!!! As I mentioned in another post, it all depends on your location and conditions as to which product will be adequate. I still have my original 20 year old can of BoeShield too. :~) I wonder what else I could use it for... |
Protect Metal Surfaces
On 2/8/2020 5:11 PM, Leon wrote:
On 2/8/2020 1:52 PM, wrote: On Sat, 8 Feb 2020 11:39:37 -0600, Leon lcb11211@swbelldotnet wrote: On 2/7/2020 9:40 PM, wrote: On Fri, 7 Feb 2020 21:22:49 -0500, Ed Pawlowski wrote: On 2/7/2020 3:47 PM, OtterGuy wrote: My woodworking tools get rust. My tables gets rust. What is the best protective stuff to apply to the table saw, bandsaw table etc. I've had good results with Boeshield T9 https://boeshield.com/ As have I.Â* It seems to last forever and works exceptionally well. Just don't put it on too thick or the wood doesn't slide well. Lasts for ever.Â* ;~)Â* I tried Boeshield on my brand new, 20 years ago, Jet TS.Â* I had rust the next morning. I put it on my 10YO Unisaur.Â* I think I've re-applied it once since. No rust.Â* Put it my drill press about 8 years ago.Â* I've never re-done it and no rust.Â* I still have the original can. No Doubt!!!Â* As I mentioned in another post, it all depends on your location and conditions as to which product will be adequate. I still have my original 20 year old can of BoeShield too.Â* :~) I wonder what else I could use it for... Here is a thought, maybe Boeing could spray it on their grounded 737 Max airplanes and..... |
Protect Metal Surfaces
On Sat, 8 Feb 2020 17:11:34 -0600, Leon lcb11211@swbelldotnet wrote:
On 2/8/2020 1:52 PM, wrote: On Sat, 8 Feb 2020 11:39:37 -0600, Leon lcb11211@swbelldotnet wrote: On 2/7/2020 9:40 PM, wrote: On Fri, 7 Feb 2020 21:22:49 -0500, Ed Pawlowski wrote: On 2/7/2020 3:47 PM, OtterGuy wrote: My woodworking tools get rust. My tables gets rust. What is the best protective stuff to apply to the table saw, bandsaw table etc. I've had good results with Boeshield T9 https://boeshield.com/ As have I. It seems to last forever and works exceptionally well. Just don't put it on too thick or the wood doesn't slide well. Lasts for ever. ;~) I tried Boeshield on my brand new, 20 years ago, Jet TS. I had rust the next morning. I put it on my 10YO Unisaur. I think I've re-applied it once since. No rust. Put it my drill press about 8 years ago. I've never re-done it and no rust. I still have the original can. No Doubt!!! As I mentioned in another post, it all depends on your location and conditions as to which product will be adequate. Mine sat in the garage in the Auburn Alabama area for three years (the drill press in an unheated attic). Since 2011, they've been in my basement (unheated) in the Atlanta area. Not exactly controlled environments. I still have my original 20 year old can of BoeShield too. :~) I wonder what else I could use it for... |
Protect Metal Surfaces
On Sat, 8 Feb 2020 17:14:28 -0600, Leon lcb11211@swbelldotnet wrote:
On 2/8/2020 5:11 PM, Leon wrote: On 2/8/2020 1:52 PM, wrote: On Sat, 8 Feb 2020 11:39:37 -0600, Leon lcb11211@swbelldotnet wrote: On 2/7/2020 9:40 PM, wrote: On Fri, 7 Feb 2020 21:22:49 -0500, Ed Pawlowski wrote: On 2/7/2020 3:47 PM, OtterGuy wrote: My woodworking tools get rust. My tables gets rust. What is the best protective stuff to apply to the table saw, bandsaw table etc. I've had good results with Boeshield T9 https://boeshield.com/ As have I.* It seems to last forever and works exceptionally well. Just don't put it on too thick or the wood doesn't slide well. Lasts for ever.* ;~)* I tried Boeshield on my brand new, 20 years ago, Jet TS.* I had rust the next morning. I put it on my 10YO Unisaur.* I think I've re-applied it once since. No rust.* Put it my drill press about 8 years ago.* I've never re-done it and no rust.* I still have the original can. No Doubt!!!* As I mentioned in another post, it all depends on your location and conditions as to which product will be adequate. I still have my original 20 year old can of BoeShield too.* :~) I wonder what else I could use it for... Here is a thought, maybe Boeing could spray it on their grounded 737 Max airplanes and..... I don't think they actually use it on their airplanes. It would take thousands of cans. Coincidence? I think not! The 737 Max may be their undoing. ...and take SouthWest Airlines with it. |
Protect Metal Surfaces
On Saturday, February 8, 2020 at 10:07:43 PM UTC-6, wrote:
Mine sat in the garage in the Auburn Alabama area for three years (the drill press in an unheated attic). Since 2011, they've been in my basement (unheated) in the Atlanta area. Not exactly controlled environments. I still have my original 20 year old can of BoeShield too. :~) I wonder what else I could use it for... Whenever you speak of "unheated" as an "uncontrolled" location and its over 150 miles from the coast, you are different from what Leon is talking about. Get a location near the coast, where your controlled location has heating and cooling that is used *in the same 24 hour period* and you will see why some people have more trouble with humidity, condensation, and rust than you do. |
Protect Metal Surfaces
|
Protect Metal Surfaces
On 2/7/2020 7:14 PM, DerbyDad03 wrote:
On Friday, February 7, 2020 at 5:13:49 PM UTC-5, OtterGuy wrote: My workshop is in the garage so not able to control humidity. I have been told that paste wax does not work. I don't know where you heard that paste wax doesn't work. Paste wax works, but sucks compared to Bostik GlideCote (TopCote). I've use both and like most things, the product specifically designed for the task works best, in this case, way best. This stuff not only inhibits rust, but makes all your tool tops slick as wet ice. This makes it a safety factor as well as a rust inhibitor. Lasts a long time as well, longer than past wax and easy to use. I even use it on all my vice/clamp threads as it makes them spin freely and no rust. -- Jack Knowledge is knowing a tomato is a fruit; Wisdom is not putting it in a fruit salad. |
All times are GMT +1. The time now is 10:51 AM. |
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter